Wells G13 Quick start guide
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
OWNERS MANUAL
ELECTRIC
COUNTERTOP
GRIDDLES
MODELS
G13, G19,
G23, G24,
G60
Includes
INSTALLATION
USE & CARE
PARTS LISTS
WIRING DIAGRAMS
101
p/n 2M-303339 Rev. G M101 130409
Model G19
101 p/n 2M-303339 OpManual Countertop Electric Griddles
equipment manufactured by WELLS BLOOMFIELD, LLC is
for a period of one year from the date of original installation
or 18 months from the date of shipment from our factory,
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW
OR IN FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has
also does not apply if the serial nameplate has been
removed, or if service is performed by unauthorized
personnel. The prices charged by Wells
products are based upon the limitations in this warranty.
Seller’s obligation under this warranty is limited to the
factory authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
to the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
the Service Policy and Procedure Guide. Wells
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
directory, your foodservice equipment dealer or contact:
Wells Bloomeld, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (314) 678-6314 or fax (314) 781-2714
for information and other details concerning warranty.
LIMITED WARRANTY STATEMENT
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
NOTE: For your protection, please note that equipment
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3. CONCEALED LOSS OR DAMAGE: if damage is
“CONCEALED DAMAGE” claim with them. This should
delivery was made to you. Be sure to retain the
container for inspection.
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
SHIPPING DAMAGE CLAIM PROCEDURE
xi
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions
are the cause.
2. All problems due to operation at voltages or phase
other than specied on equipment nameplates
are not covered by this warranty. Conversion to
correct voltage and/or phase must be the customer’s
responsibility.
3. All problems due to electrical connections not made
in accordance with electrical code requirements
and wiring diagrams supplied with the equipment are
not covered by this warranty.
4. Replacement of items subject to normal wear, to
maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
to excessive heat are not covered by this warranty.
6. Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and
cleaning schedules, are customer responsibility. Those
miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures
will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an
Authorized Service Agency or one of its sub-service
agencies.
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted for
ninety (90) days from date of purchase on non-warranty
equipment. This parts warranty is limited only to
replacement of the defective part(s). Any use of non-
genuine Wells parts completely voids any warranty.
considered warranty and are thus not covered by this
warranty.
11. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technician’s ability to
perform service are not covered by warranty. This
includes institutional and correctional facilities.
101 p/n 2M-303339 OpManual Countertop Electric Griddles
WARRANTY xi
SPECIFICATIONS 1
FEATURES & OPERATING CONTROLS 2
PRECAUTIONS & GENERAL INFORMATION 3
AGENCY LISTING INFORMATION 4
INSTALLATION 4
OPERATION 6
CLEANING INSTRUCTIONS
Standard and Grooved Griddles 8
Chrome-Plated griddles 9
TROUBLESHOOTING SUGGESTIONS 10
EXPLODED VIEW & PARTS LIST 11
WIRING DIAGRAM 23
PARTS & SERVICE 29
CUSTOMER SERVICE DATA 29
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.
TABLE OF CONTENTS
SPECIFICATIONS
INTRODUCTION
1
MODEL VOLTS WATTS AMPS 3ø AMPS
L1 L2 L3 N 1ø
G13 208/240V 6,750 / 9,000 14.0 / 18.7 28.1 / 32.5 14.0 / 18.7 32.5 / 37.5
480 9,000 9.4 16.2 9.4 18.7
G13EU 380-415V 10,800 15 15 15 0
G19 208V 12,000 28.8 49.9 28.8 57.6
240V 12,000 25 43.3 25 50
480V 12,000 12.5 21.7 12.5 25
G19EU 380-415V 16,100 22.5 22.5 225 0
G23
208V 16,000 48.3 51.3 35 76.9
240V 16,000 41.7 44.4 30.4 66.6
208/240V 12,000 / 16,000 36.2 / 41.7 38.5 / 44.4 26.3 / 30.4 57.7 / 66.6
480V 16,000 20.9 22.2 15.5 33.3
G23EU 380-415V 16,000 15.8 31.6 19.2 38.6
G24 208V 21,500 63.4 67.1 45.8 103.3
240V 21,500 55 58.3 39.6 89.5
480V 21,500 27.1 28.9 19.9 43.8
G24EU 380-415V 21,000 20.8 41.7 25 50.6
G60 208V 32,000 48.3 51.3 35 76.9 x 2
240V 32,000 41.7 44.4 30.4 66.6 x 2
480V 32,000 20.9 22 15.1 33.3 x 2
FEATURES & OPERATING CONTROLS
2
Fig. 1 Countertop Griddle Features & Operating Controls
G19 Shown - G13, G23, G24 and G60 are Similar
101 p/n 2M-303339 OpManual Countertop Electric Griddles
101 p/n 2M-303339 OpManual Countertop Electric Griddles
TEMPERATURE CONTROL
Power is applied to the heating elements according to the control
knob position and the actual temperature sensed at the thermobulb.
When the element is energized the heating indicator will glow.
Each section of the griddle is individually controllable.
Dial position is an indication of the temperature setting. The actual
temperature at the griddle surface will vary, depending upon the initial
type and temperature of the product, and other variables.
GREASE TROUGH Extra-wide trough with radiused corners for easier cleaning. Trough
slopes toward a large waste hole that empties into the removable
grease drawer.
GREASE DRAWER Large-capacity drawer is removable through the front for easy
cleaning.
REMOVABLE SPLASH GUARD Stainless steel aplash guard simplies griddle maintenance and helps
to keep grease from splattering onto adjacent walls and equipment
ADJUSTABLE LEGS Adjustable for use in leveling the griddle. Allow for ventilation and
cleaning underneath.
NAMEPLATE Lists manufacturer’s information, model and serial number. Also lists
electrical specications.
SPLASHGUARD
GREASE TROUGH
GREASE DRAWER
TEMPERATURE
CONTROL
KNOB
HEATING
INDICATOR
NAMEPLATE
ADJUSTABLE LEG
350
450
400
IL2108
101 p/n 2M-303339 OpManual Countertop Electric Griddles
101 p/n 2M-303339 OpManual Countertop Electric Griddles
3
This appliance is intended for use in commercial establishments
only.
This appliance is intended
to prepare food for human consumption.
No other use is
recommended or authorized by the manufacturer or its
agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect this appliance from electrical power before performing any
maintenance or servicing.
DO NOT submerge this appliance in water. This appliance is not jet
stream approved. Do not direct water jet or steam jet at this appliance,
or at any control panel or wiring. Do not splash or pour water on, in or
over any controls, control panel or wiring.
Exposed surfaces of this appliance can be hot to the touch and may
cause burns.
The technical content of this manual, including any wiring diagrams,
Any procedure which requires the use of tools must be performed by a
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
CAUTION:
RISk OF
DAMAGE
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance will result if
these instructions are not
followed.
CAUTION:
HOT SURFACE
Exposed surfaces can be hot
to the touch and may cause
burns.
PRECAUTIONS AND GENERAL INFORMATION
DANGER: BURN HAZARD
and avoid contact with griddle surface.
WARNING: ELECTRIC SHOCk HAZARD
All servicing requiring access to non-insulated components must be performed by
AGENCY LISTING INFORMATION
STD 4
E6070
INSTALLATION
NOTE: DO NOT discard
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE
CLAIM PROCEDURE on the
inside front cover of this
manual.
IMPORTANT:
This installation must comply
with all applicable Federal,
Local and NFPA codes.
UNPACkING & INSPECTION
Carefully remove the appliance from the carton. Remove all protective
before connecting electrical power or otherwise performing any
installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet
installation.
Read and understand all labels and diagrams attached to the
appliance.
Carefully account for all components and accessories before
place for later use.
COMPONENTS
1 ea. GREASE DRAWER (2 ea. for G-60)
1 ea. SCRAPER (for grooved griddle plates, if ordered)
1 ea. SPLASHGUARD
4 ea. ADJUSTABLE LEGS (6 ea. for G-60)
SETUP
Verify local codes for requirements. Concrete, tile, terrazzo or metal
surfaces are recommended. Metal over combustible material may not
meet code for non-combustible surfaces.
Install one adjustable leg at each corner of the griddle by screwing the
ON ALL
FOUR LEGS.
contact the counter in order to prevent tipping.
Refer to the Installation Instruction Sheet for required clearances.
Maintain required clearances between the appliance and adjacent
combustible surfaces.
appliance.
This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied Installation Instructions and
maintained according to the instructions in this manual.
This appliance is UListed under UL File E6070 for 120V, 208V and
240V.
4
Fig. 2 Adjustable Legs
101 p/n 2M-303339 OpManual Countertop Electric Griddles
101 p/n 2M-303339 OpManual Countertop Electric Griddles
INSTALLATION (continued)
WARNING: ELECTRIC SHOCk HAZARD
All servicing requiring access to non-insulated electrical components must be performed by a
factory authorized technician.
DO NOT open any access panel which requires the use of tools. Failure to follow this warning
CAUTION:
RISk OF
DAMAGE
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance will result
if these instructions are not
followed.
CAUTION:
ELECTRICAL
SHOCk HAZARD
This griddle must be
electrically grounded.
“GND” or “ ” to a suitable
building ground.
IMPORTANT:
Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.
ELECTRICAL INSTALLATION
Refer to the nameplate. Verify the electrical service power. Voltage
griddle to the wrong voltage can severely damage the unit or cause
noticeably decreased performance.
IMPORTANT: Damage due to being connected to the wrong voltage is
NOT covered by warranty.
Use copper wire suitable for at least 90ºC for supply connections.
Griddles are factory wired three-phase (3ø).
For single-phase (1ø) wiring, refer to the wiring diagram attached to the
griddle.
This griddle is not fused. Protect the circuit with properly sized fuses or
An electrical disconnect must be installed readily accessible to the
operator of the griddle.
EQUIPMENT SETUP
grease trough.
Slide grease drawer into grease drawer sleeve in front of griddle.
OPERATION
6
PREPARING THE GRIDDLE SURFACE
SEASONING STANDARD AND GROOVED GRIDDLES
As manufactured, the steel surface of your Wells griddle has
d. Wipe griddle surface with clean damp cloth to remove all oil.
e. For new griddles, repeat this procedure 2-3 times until griddle
CHROME PLATED GRIDDLES
chrome plating, no seasoning of the griddle surface is required.
a. Thoroughly clean griddle surface using a soft clean cloth and a
small amount of mild detergent.
b. Rinse and dry thoroughly after cleaning.
c. The griddle is now ready to use.
USING THE GRIDDLE
indicator light will glow while the griddle is heating. When the indicator
For standard griddles:
Keep the griddle surface clean and well oiled during use.
For chrome plated griddles:
order.
DO NOT bang or tap pots, pans, spatulas or other metal utensils on
the griddle surface as this may damage the chrome plating.
NOTE:
Separate sections of griddle may be set to different temperatures.
This will allow a variety of products to be prepared at the same time,
and will allow prepared product to be held at serving temperature after
For best results, different temperatures should be set from coolest to
hottest sequentially across the width of the griddle. (Heat will migrate
over the entire griddle surface. Setting one section low, adjacent to a
thermostat tries to compensate for heat lost to the “low” section.)
•
•
•
•
•
CAUTION:
HOT SURFACE
Exposed surfaces can be
very hot and may cause
severe burns on contact.
IMPORTANT:
SCRATCHES WILL
DAMAGE THE SURFACE
OF CHROME-PLATED
GRIDDLES.
DO NOT use anything on
chrome griddle that could
scratch the surface.
DO NOT clean chrome
pumice stone or abrasive
cleansers.
101 p/n 2M-303339 OpManual Countertop Electric Griddles
101 p/n 2M-303339 OpManual Countertop Electric Griddles
7
OPERATION (continued)
RECOMMENDED GRILLING TIMES AND TEMPERATURES NOTE:
The times and temperatures
in this chart are suggestions
only.
Your own experience with
your own menu items will be
your best guide to achieving
the best food product.
PRODUCT TEMP ºF TIME
3 minutes
Bacon 2 - 3 minutes
Canadian Bacon 2 - 3 minutes
3 - 4 minutes
Broiled Ham 2 minutes
Beef Tenderloin 400º 3 - 4 minutes
400º 3 - 4 minutes
400º
Hamburgers 3 - 4 minutes
Cheeseburgers 3 - 4 minutes
Melted Cheese Sandwich 3 - 4 minutes
Hot Dogs 2 - 3 minutes
8
CLEANING INSTRUCTIONS - STANDARD AND GROOVED GRIDDLES
PREPARATION Set temperature control to 220ºF. Allow
griddle temperature to drop to 220ºF before
proceeding.
FREQUENCY Daily
TOOLS
Plastic Scouring Pad, Plastic Scraper
Contoured Scraper (grooved griddle)
Mild Detergent, Non-Abrasive Cleanser
Clean Soft Cloth / Sponge
CLEANING
Pour a small amount of water on the griddle surface and let it “sizzle”.
Clean the griddle surface:
scrape food waste. Clean the griddle surface down to bright
metal. Wipe off any remaining powder residue.
b. For grooved-surface griddles, use the supplied contoured
scraper to scrape food waste. Clean the griddle surface down
to bright metal.
remaining food particles.
Turn temperature control to OFF. Allow the griddle surface to cool,
then wipe the surface with a clean cloth. Dry the griddle surface
thoroughly.
IMPORTANT: SEASON THE COOKING SURFACE AFTER EACH
CLEANING. Refer to page 6.
At least once each day, the grease trough must be thoroughly cleaned.
Using a scraper, remove all grease and food waste from the grease
trough by pushing it down the waste hole and into the grease drawer.
dispose of all waste.
a. Clean drawer with hot water and a mild detergent.
b. Dry drawer thoroughly and reinstall in griddle.
or in the dishwasher. Rinse thoroughly and reinstall.
Wipe down exterior of griddle cabinet with a clean cloth and
non-abrasive cleanser. Rinse thoroughly with water and a clean cloth.
Dry with a soft clean cloth
Procedure is complete.
CAUTION:
BURN HAZARD
Griddle will be hot during
portions of this cleaning
procedure. Always heat-
protective gloves and apron.
CAUTION:
ELECTRIC SHOCk
HAZARD
Do not submerge griddle in
water.
IMPORTANT: DO NOT spill
or pour water into controls,
control panel or wiring.
DO NOT submerge griddle
in water. Damage to internal
components will occur.
Damage to internal
components from water
damage is not covered by
warranty.
IMPORTANT: NEVER USE
STEEL WOOL TO CLEAN
THE GRIDDLE SURFACE!
DO NOT use detergent or
oven cleaner to clean the
griddle surface.
IMPORTANT: DO NOT
use steel wool or abrasive
cleansers for cleaning the
griddle cabinet.
101 p/n 2M-303339 OpManual Countertop Electric Griddles
101 p/n 2M-303339 OpManual Countertop Electric Griddles
9
PREPARATION Set temperature control to 220ºF. Allow
griddle temperature to drop to 220ºF before
proceeding.
FREQUENCY Daily
TOOLS 4” Razor-Style Scraper, Soft Bristle Brush
Mild Detergent, Non-Abrasive Cleanser
Clean Soft Cloth / Sponge
CLEANING
Pour a small amount of water on the griddle surface and let it “sizzle”.
Use a 4” razor-style scraper to clean the remaining food particles from
the griddle surface
IMPORTANT: NEVER USE GRIDDLE BRICKS, PUMICE STONES
OR STEEL WOOL TO CLEAN THE GRIDDLE SURFACE!
DO NOT use detergent or oven cleaner to clean griddle surface.
IMPORTANT: NEVER BANG OR TAP METAL IMPLEMENTS,
SPATULAS, POTS, PANS, OR SCRAPERS ON THE GRIDDLE
SURFACE!
remaining food particles.
Turn temperature control to OFF. Allow the griddle surface to cool,
then wipe the surface with a clean cloth. Dry the griddle surface
thoroughly.
At least once each day, the grease trough must be thoroughly cleaned.
Using a scraper, remove all grease and food waste from the grease
trough by pushing it down the waste hole and into the grease drawer.
dispose of all waste.
a. Clean drawer with hot water and a mild detergent.
b. Dry drawer thoroughly and reinstall in griddle.
or in the dishwasher. Rinse thoroughly and reinstall.
Wipe down exterior of griddle cabinet with a clean cloth and
non-abrasive cleanser. Rinse thoroughly with water and a clean cloth.
Dry with a soft clean cloth
Procedure is complete.
CAUTION:
BURN HAZARD
Griddle will be hot during
portions of this cleaning
procedure.
Always heat-protective gloves
and apron.
CAUTION:
ELECTRIC
SHOCk HAZARD
Do not submerge griddle in
water.
IMPORTANT: DO NOT spill
or pour water into controls,
control panel or wiring.
DO NOT submerge griddle
in water. Damage to internal
components will occur.
Damage to internal
components from water
damage is not covered by
warranty.
IMPORTANT: DO NOT use
abrasive cleansers to clean
surface.
IMPORTANT: DO NOT
use steel wool or abrasive
cleansers for cleaning the
griddle cabinet .
IMPORTANT:
Never bang or tap metal
implements, spatulas, pots,
pans or scrapers on the
griddle surface.
CLEANING INSTRUCTIONS - CHROME PLATED GRIDDLES
10
TROUBLESHOOTING SUGGESTIONS
101 p/n 2M-303339 OpManual Countertop Electric Griddles
DESCRIPTION POSSIBLE PROBLEM SUGGESTED REMEDY
Griddle will not heat Circuit breaker off or tripped Reset circuit breaker
One section does not heat
Temperature control knobs not set to
desired temperature Set to desired temperature
Damaged internal component Contact WellsAuthorized Service
Agency for repairs
Griddle drips grease Grease drawer full or not installed Empty grease drawer. Install properly
Damaged internal component Contact WellsAuthorized Service
Agency for repairs
NOTE: There are no user serviceable components in the griddle. In all cases of damage or malfunction, contact
yourAuthorized Wells ServiceAgency for repairs.
101 p/n 2M-303339 OpManual Countertop Electric Griddles
EXPLODED VIEW & PARTS LIST
FIELD CONVERSION FROM 3-PHASE TO SINGLE-PHASE
Griddles are shipped from the factory wired for 3-phase power,
CONTROL kNOB CONFIGURATION
When the thermostat is OFF
*
*NOTE: G60
has 2 separate
electrical supplies
11
12
EXPLODED VIEW & PARTS LIST
101 p/n 2M-303339 OpManual Countertop Electric Griddles
COUNTERTOP ELECTRIC GRIDDLE
MODEL G13, PG13 - HEATING ELEMENTS
208/240V and 480V
COVER, GREASE DRW
G7-31995
CLIP, TIE-DOWN INSULATION
G7-33474
CLAMP, ELEMENT END
G7-31969
NUT, HEX 10-32
2C-35313
CLAMP, ELEMENT CENTER
G7-31968
JUMPER, ELEMENT SHORT
2E-32054
ELEMENT 2250W
240V, 2N-30496UL
480V, 2N-48904UL
NUT, 1/4-20 HEX NI
2C-31253
CLAMP, THERMO BULB
G7-32028
TUBE, THERMO BULB 18”
2A-31972
INSULATION PAD (2’X4’)
2H-36051
GRIDDLE (REF.)
shown inverted
FRONT
IL1918, Rev. A
Electric Griddle G13
HEATING ELEMENTS
208/240V 1ø
101 p/n 2M-303339 OpManual Countertop Electric Griddles
EXPLODED VIEW & PARTS LIST
13
COUNTERTOP ELECTRIC GRIDDLE
MODEL G13, PG13 - CABINET & ELECTRICAL
208/240V and 480V
IL1917, Rev F, 4/09/13
GRIDDLE PLATE ASSY
G13; DD-35663
PG13; DD37437
SPLASHGUARD, LEFT G7-35781
SPLASHGUARD, REAR G7-34437
SPLASHGUARD, RIGHT G7-35780
LIGHT, SIGNAL AMBER
208/240V 2J-30516
380/415V M3-WL0113
(2 ea)
KNOB
2R-30259
(2 ea)
TRIM RING
D8-30256(2 ea)
SHIELD, THERMO
2A-31974 (2ea)
SLEEVING, 5/16
1O-32040
(2 ea)
THERMO, CONTROL
2T-30257
G7-WL0335 (G13-300F only), (2ea)
(2ea)
DOMED LABEL
2M-300534
FEET, 4" ADJUSTABLE
2A-30586 (GREY PLASTIC)
2A-Z0314 (METAL)
SHROUD, GREASE
DRW WS-51989
SCREW, 8-32x3/8
2C-34285 (6 ea)
SCREW, 6-32x3/16
2C-31718 (4 ea)
SPLASHGUARD G-13
COMPLETE ASSY
5G-20632
HANDLE
2R-38668
TRAY FRONT
G7-Z12047
GREASE TRAY ASSY
COMPLETE WS-50279
SHELL ASSY (ref.)
FRONT PANEL
(ref.)
SCREW 6ABx5/16
2C-33935 (15 ea)
BUSHING, HEYCO
2K-31040 (2ea)
TERMINAL BLOCK 3P 85AMP
WS-50131
NUT, KEPS GREEN
2C-35736
G7-31990
NUT, ALUM 7/8” LONG
2C-41974 (2ea)
Electric Griddle G13, PG13
CABINET COMPONENTS
208/240V 1ø
EXPLODED VIEW: G19
101 p/n 2M-303339 OpManual Countertop Electric Griddles
14
COUNTERTOP ELECTRIC GRIDDLE
MODEL G19 - HEATING ELEMENTS
208V, 240V, 380-415V and 480V
IL1919, Rev. B
ELECTRIC GRIDDLE G19
HEATING ELEMENTS
20060 208V 1ø
20062 240V 1ø
GRIDDLE
SHOWN INVERTED
(ref.)
11
10
9
8
7
6
5
1
2
3
4
101 p/n 2M-303339 OpManual Countertop Electric Griddles
EXPLODED VIEW: G19
COUNTERTOP ELECTRIC GRIDDLE
MODEL G19 - CABINET & ELECTRICAL
208V, 240V, 380-415V and 480V
ELECTRIC GRIDDLE G19
CABINET COMPONENTS IL1920, Rev C
12
13
14
15
16
23
22
21
20
19
18
17
34 35
24
33
32
31 30
29
28
27
26
25
PARTS LIST: G19 208V, 240V, 380-415V and 480V
16
101 p/n 2M-303339 OpManual Countertop Electric Griddles
G19 COUNTERTOP ELECTRIC GRIDDLE
Fig No Part No Qty Description Application
1 2C-31253 AR NUT 1/4-20 FINISHED HEX
2 G7-31968 10 CLAMP ELEM CTR SMALLGRID
3G7-32038 8 CLAMP ELEM END LRG GRID
G7-46169 3 CLAMP ELEM EU ROHS 380/415V
4
2N-30511UL 4 ELEM 208V 3000W 208V
2N-30512UL 4 ELEM 240V 3000W 240V
2N-45922UL 3 ELEM 220V 4500 EU 380/415V
2N-48902UL 4 ELEM HEATING 480V 3000W 480V
5 2C-35313 8 NUT 10-32 HEX MS SS 208/240/480V
6 2E-32055 4 JUMPER, ELEMENT LONG 208V, 240V, 480V
7 2A-31972 2 TUBE THERMOW 18 LINE GRID
8G7-32028 4 CLAMP THERMO BULB GRIDDLE
G7-46178 3 CLAMP THERMO BULB GRIDLEU 380/415V
9 G7-33474 11 CLIPTIE DOWN INSUL GRIDDLE
12 380/415V
10 G7-31995 1COVER GREASE DRWR
G7-46180 CVR GREASE DRWR 380/415V
11 2H-36051 6 INSULFG 1X24X48
12 WS-20634 1 SPLASHGUARD G-196
13 G7-35781 1 SPLASHGUARD LF GRVD 24IN
14 G7-34436 1 SPLASHGUARD REARASSY
15 G7-35780 1 SPLASHGUARD RTGRVD 24IN
16 CALLFACTORY 1 G19, GRIDDLE ASSY
17 2R-30259 2 KNOB CONTROLASSY
2R-46164 3 KNOB THERMO JG246EU 380/415V
18 2C-31718 AR SCREW 6-32X3/16 PH RD HD
19 D8-30256 2TRIM RINGASSY
3 380/415V
20 2J-30516 2 LIGHT SIGNALAMBER 208V, 240V
M3-WL0113 2ASSY, PILOT LIGHTABMER 480V
3 380/415V
21 2A-31974 2SHIELD THERMO GRID
3 380/415V
22 2T-46162 3 THERMO JG246EU 380/415V
WS-50257 2 THERMO GRIDL SA157-36
23 IO-32040 6FT SLEEVING GLASS 5/16 I.D.
24 2K-31040 2 BUSHIGN HEYCO 7/8 O.D.
25 2E-40310 1TERM BLOCK 4 POLE 75AMP 380/415V
WS-37465 TERM BLOCK 3 POLE 115AMP 208V, 240V, 480V
26 2C-35736 AR NUT 8-32 HEX KEPS MS GREEN
27 2C-41974 2 NUT 8-32 HEX 7/8 LONGALU
28 2C-34285 AR SCREW 8-32X3/8 PH
29 2A-30586 4BLK PLASTIC LEF, 4 INCH
2A-Z0314 FOOT, 4” DIE CAST 380/415V
30 2C-33935 AR SCREW 6ABX5/16 PH PAN SMS
31 WS-50279 1 DRAWER GREASE W/HANDLE
32 G7-Z12047 1 PANEL FRONT - GREASE DR
33 2R-38668 1 HANDLE DOOR
34 2M-300534 1 TRADEMARK DOMES LABEL
35 WS-51989 1 SHROUD GREASE DRAWER
NI 2K-300102 1 STRAIN RELIEF 1NPT .375-1 380/415V
10
EXPLODED VIEW & PARTS LIST: G23
101 p/n 2M-303339 OpManual Countertop Electric Griddles
17
COUNTERTOP ELECTRIC GRIDDLE
MODEL G23 - HEATING ELEMENTS
208V, 240V and 480V
ELECTRIC GRIDDLE G23
HEATING ELEMENTS
20068 208V
20070 240V
HEATING ELEMENT
3800W / 208V 2N-30510UL
3800W / 240V 2N-30509UL
(DUAL VOLTAGE)
3800W / 480V 2N-31428UL
HEATING ELEMENT, PERIMETER
800W / 208/240V 2N-30508UL
800W / 480V WS-31495UL
(4 ea)
NUT, 10-32
HEX 2C-35313
(10 ea)
NUT, 1/4-20 HEX Ni
2C-31253 (36 ea)
CLAMP, ELEM CENTER
DD-32037 (10 ea)
CLAMP, ELEM END
G7-32038 (8 ea)
CLAMP, PERIMETER
ELEMENT RIGHT
G7-32026
CLAMP, PERIMETER
ELEMENT LEFT G7-32027
CLAMP, THERMO
G7-32028 (12 ea)
TUBE, THERMO
2A-31971 (4 ea)
CLIP, INSULATION
G7-33474 (12 ea)
COVER, GREASE
DRAWER G7-31995
INSULATION PAD
2H-36051 (pk 2'x4')
GRIDDLE
SHOWN INVERTED
(ref.)
CLAMP, PERIMETER
ELEMENT CENTER
(6 ea) G7-32025
IL1921, Rev A
EXPLODED VIEW & PARTS LIST
18
COUNTERTOP ELECTRIC GRIDDLE
MODEL G23 - CABINET & ELECTRICAL
208V, 240V and 480V
ELECTRIC GRIDDLE G23, PG23
CABINET COMPONENTS
GRIDDLE PLATE ASSY
WS-55666, G23
G7-G23-PL-NGR, PG23
LIGHT, SIGNAL AMBER
208 / 240V 2J-30516
380 / 480V M3-WL0113
(4 ea)
KNOB
2R-30259(4 ea)
TRIM RING
D8-30256(4 ea)
SHIELD, THERMO
2A-31974 (4 ea) SLEEVING, 5/16
1O-32040 (4 ea)
THERMO, CONTROL
2T-30257 (4 ea)
BUSHING, HEYCO
2K-31040(2 ea)
TERMINAL BLOCK
3P 115AMP (208/240V) WS-57465
3P 75A (480V) 2E-30412
NUT, KEPS GREEN
2C-35736
NUT, ALUM 7/8 LONG
2C-41974 (2ea)
BASE, SHELL ASSY
WS-51487
FRONT PANEL
G7-Z12109
SHROUD, GREASE
DRAWER WS-51989
SCREW, 8-32x3/8
2C-34285 (6 ea)
HANDLE
2R-38668
DOMED
LABEL
2M-300534
TRAY FRONT
G7-Z12047
SCREW 6ABx5/16
2C-33935 (15 ea)
GREASE DRAWER
COMPLETE ASSY
WS-50279
FEET, 4" ADJUSTABLE
2A-30586 (GRAY PLASTIC)
2A-Z0314 (METAL)
IL1922, Rev B
SPLASH GUARD ASSY, G-23
COMPLETE 5G-20635
SPLASHGUARD, LEFT
G7-35783
SPLASHGUARD, RIGHT
G7-35782
SPLASHGUARD, REAR
G7-34436
G7-31990
101 p/n 2M-303339 OpManual Countertop Electric Griddles
Other manuals for G13
1
This manual suits for next models
4
Table of contents
Other Wells Griddle manuals
Wells
Wells WVG-136 SERIES User manual
Wells
Wells G-136 User manual
Wells
Wells HDG Series User manual
Wells
Wells WVG-136 SERIES User manual
Wells
Wells WVG-136 SERIES Operating instructions
Wells
Wells WG-2424G User manual
Wells
Wells WG-2424G User manual
Wells
Wells HDTG-2430G User manual
Wells
Wells G-13EU User manual
Wells
Wells WV2HG Series User manual
