Wen BA1487 User manual

14-INCH TWO-SPEED
BAND SAW WITH STAND
Instruction Manual
IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability,
ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged,
trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use
your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
TECHSUPPOR[email protected]1-800-232-1195 (M-F 8AM-5PM CST)
For replacement parts and the most up-to-date instruction manuals, visit WENPRODUCTS.COM
MODEL BA1487

2
CONTENTS
WELCOME 3
Introduction ......................................................................................................3
Specifications................................................................................................... 3
SAFETY 4
General Safety Rules........................................................................................ 4
Specific Rules for Your Band Saw.................................................................... 6
Electrical Information....................................................................................... 8
9
Unpacking & Packing List................................................................................ 9
Know Your Band Saw..................................................................................... 10
Assembly & Adjustments............................................................................... 11
BEFORE OPERATING
OPERATION & MAINTENANCE 17
Operation ....................................................................................................... 17
Maintenance....................................................................................................20
Exploded View & Parts List............................................................................ 21
Warranty Statement ....................................................................................... 26
To purchase accessories for your tool, visit WENPRODUCTS.COM
Woodcutting Bandsaw Blade (Models BB9912, BB9925, BB9950)

INTRODUCTION
Thanks for purchasing the WEN Band Saw. We know you are excited to put your tool to work, but first, please
take a moment to read through the manual. Safe operation of this tool requires that you read and understand this
operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety
concerns, as well as helpful assembly and operating instructions for your tool.
NOTE: The following safety information is not meant to cover all possible conditions and situations that may occur.
WEN reserves the right to change this product and specifications at any time without prior notice.
At WEN, we are continuously improving our products. If you find that your tool does not exactly match this manual,
please visit wenproducts.com for the most up-to-date manual or contact our customer service at 1-800-232-1195.
Keep this manual available to all users during the entire life of the tool and review it frequently to maximize
safety for both yourself and others.
SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. The safety symbols and the explanations
with them deserve your careful attention and understanding. Always follow the safety precautions to reduce the
risk of fire, electric shock or personal injury. However, please note that these instructions and warnings are not
substitutes for proper accident prevention measures.
SPECIFICATIONS
Model Number BA1487
Motor 120V, 60 Hz, 9.5A
Throat 13-3/8 Inches
Cutting Depth 8.85 Inches
Blade Speed 1480 / 3280 FPM
Table Angle 0ºto 45º
Work Table Dimensions 18.90 in. x 15.35 in.
Blade Length 100-3/4 Inches
Blade Width 1/8 to 1 Inch
Product Weight 130.95 Pounds
Product Dimensions 21 in. x 31 in. x 67 in.
3

GENERAL SAFETY RULES
4
WORK AREA SAFETY
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
3. Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodi-
fied plugs and matching outlets will reduce risk of elec-
tric shock.
2. Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges and refrigera-
tors. There is an increased risk of electric shock if your
body is earthed or grounded.
3. Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the risk
of electric shock.
4. Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep cord
away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of elec-
tric shock.
5. When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
6. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of a GFCI reduces the risk
of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
2. Use personal protective equipment. Always wear
eye protection. Protective equipment such as a respi-
ratory mask, non-skid safety shoes and hearing protec-
tion used for appropriate conditions will reduce the risk
of personal injury.
3. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites
accidents.
4. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
5. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or jew-
elry. Keep your hair and clothing away from moving
parts. Loose clothes, jewelry or long hair can be caught
in moving parts.
Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE SAFETY INSTRUCTIONS.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.

GENERAL SAFETY RULES
5
7. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
3. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
5. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s opera-
tion. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained
power tools.
6. Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situa-
tion.
8. Use clamps to secure your workpiece to a stable
surface. Holding a workpiece by hand or using your
body to support it may lead to loss of control.
9. KEEP GUARDS IN PLACE and in working order.
SERVICE
1. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is main-
tained.
CALIFORNIA PROPOSITION 65 WARNING
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities may contain
chemicals, including lead, known to the State of Califor-
nia to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling. Some examples of
these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
masonry products.
• Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies depending on
how often you do this type of work. To reduce your ex-
posure to these chemicals, work in a well-ventilated area
with approved safety equipment such as dust masks
specially designed to filter out microscopic particles.
Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”
in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
SAVE THESE SAFETY INSTRUCTIONS.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.

SAW BLADE SAFETY
1. Always wear protective gloves when handling saw
blades.
2. Only use blades with correct size and type for both
your band saw and your workpiece.
• See the blade specifications on page 3.
• Make sure the blade is installed in the proper direc-
tion.
3. Never use damaged or deformed saw blades. Only
use sharp blades.
4. Install the saw blade in the correct orientation indi-
cated in the instructions (see “Changing the Saw Blade”,
page 17).
5. Keep hands out of path of saw blade. Never use your
hands to remove sawdust or scrap wood. Use a brush
at all times.
6. Never reach around saw blade or reach in back of the
saw blade.
7. The use of accessories or attachments not recom-
mended by the manufacturer may result in a risk of per-
sonal injury.
PERSONAL SAFETY
1. Operate in a well ventilated area. Keep the floor area
around the band saw level and free of slippery sub-
stances or other tripping hazards.
2. Wear ANSI Z87.1-approved safety goggles to protect
your eyes from saw dust. Use hearing protection to pro-
tect yourself from hearing loss.
3. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in close
proximity to pacemakers could cause pacemaker inter-
ference or pacemaker failure.
4. Wear work gloves when handling saw blades. DO
NOT wear gloves, neckties, jewelry, or loose clothing
while operating the saw.
5. Saw dust is harmful to your health. Use NIOSH-ap-
proved dust masks or other respiratory protection dur-
ing operation and cleaning.
6. Always turn off and unplug the band saw before mak-
ing any adjustments or repair tasks. Never adjust the
band saw or the workpiece while the saw is running.
7. Only use the band saw to cut wood.
PREPARING THE BAND SAW
1. When transporting the band saw, never carry the de-
vice by its guards or its accessories.
2. Examine the band saw for any damaged or missing
parts. Replace or repair damaged parts before opera-
tion. Periodically check that all nuts, bolts and other fas-
teners are properly tightened.
SECURE YOUR WORKPIECE
1. To avoid blade binding or loss of control, always se-
cure the workpiece to a stable platform, ensuring that
body exposure is minimized.
2. Ensure that work is correctly supported. Supports
must be placed under the workpiece on both sides,
close to the line of cut and near the edge of the work-
piece.
3. For accuracy of cut, and to avoid blade binding, al-
ways use a rip fence or straight edge guide.
4. Use extra caution with very large, very small, or awk-
wardly-shaped workpieces. Small pieces should be se-
cured with clamps. Do not hold small pieces with your
hand because your fingers might go under the blade
guard.
SPECIFIC RULES FOR YOUR BAND SAW
WARNING! Do not operate the power tool until you have read and understood the following instructions
and the warning labels.
6

5. Never hand-hold a workpiece that is too small to be
clamped, as it can be launched away and cause inju-
ry. Use proper support and guides to secure the small
workpiece.
6. Support round work properly (use a V block or press
it against the miter gauge) to prevent it from rolling and
the blade from biting.
7. Plan intricate or small work carefully to avoid pinch-
ing the blade. Avoid awkward operations and hand posi-
tions to prevent accidental contact with the blade.
DURING CUTTING OPERATIONS
1. Always stand to one side when operating the saw.
Never have any part of the body in line with the path of
the saw. Never hold a workpiece in your hand or across
your legs while cutting.
2. Ensure hands are away from the cutting area and
blade.
3. Feed work into the blade against the direction of rota-
tion of the blade only.
4. If you are interrupted when operating the saw, com-
plete the process and switch the saw off before looking
up.
5. Power tools must always be held by the insulated
gripping surfaces when performing an operation, en-
suring protection if the cutting tool makes contact with
its own cord or hidden wiring. Contact with a ‘live’ wire
will make exposed metal parts of the power tool ‘live’
and shock the operator if the insulated gripping surfac-
es are not used.
6. Do not use the band saw unless all guards are in
place. Do not operate with any guard disabled, dam-
aged, or removed. Moving guards must move freely and
close instantly.
7. Blade guide, supports, bearings, and blade tension
must be properly adjusted to avoid accidental blade
contact and to minimize blade breakage. To maximize
blade support, always adjust the upper blade guide and
blade guard so that it barely clears the workpiece.
8. Turn on the band saw and let it reach full speed, then
slowly slide the workpiece into the blade. This will help
produce safer and cleaner cuts.
9. Never cut more than one piece at a time. Do not stack
workpieces together. Do not attempt to cut material
thicker than specified on page 3 of this manual. Adjust
the upper blade guide to suit the thickness of the work-
piece.
10. If a cut does not extend to the edge of the work-
piece, or if the blade binds in the cut, allow the blade
to come to a complete stop and lift the workpiece away
from the blade.
11. Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings. Do not slow
or stop a blade with a piece of wood or by hand. Let
the blade come to rest naturally. Do not attempt to free
a jammed blade while the machine is still running and
connected to power.
12. Always adjust the upper blade guide to cover the
blade after use.
SPECIFIC RULES FOR YOUR BAND SAW
WARNING! Do not operate the power tool until you have read and understood the following instructions
and the warning labels.
7

ELECTRICAL INFORMATION
8
AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS
25 ft. 50 ft. 100 ft. 150 ft.
9.5A 18 gauge 16 gauge 14 gauge 12 gauge
3. Check with a licensed electrician or service personnel if you do not completely under-
stand the grounding instructions or whether the tool is properly grounded.
4. Use only three-wire extension cords that have three-pronged plugs and outlets that
accept the tool’s plug. Repair or replace a damaged or worn cord immediately.
CAUTION! In all cases, make certain the outlet in question is properly grounded. If you
are not sure, have a licensed electrician check the outlet.
GUIDELINES AND RECOMMENDATIONS FOR EXTENSION CORDS
When using an extension cord, be sure to use one heavy enough to carry the current
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides the path of least resistance for an electric current
and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding
conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and
grounded in accordance with ALL local codes and ordinances.
1. Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a licensed electri-
cian.
2. Improper connection of the equipment grounding conductor can result in electric shock. The conductor with
the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement
of the electric cord or plug is necessary, DO NOT connect the equipment grounding conductor to a live terminal.
1. Examine extension cord before use. Make sure your extension cord is properly wired and in good condition.
Always replace a damaged extension cord or have it repaired by a qualified person before using it.
2. Do not abuse extension cord. Do not pull on cord to disconnect from receptacle; always disconnect by pulling
on plug. Disconnect the extension cord from the receptacle before disconnecting the product from the extension
cord. Protect your extension cords from sharp objects, excessive heat and damp/wet areas.
3. Use a separate electrical circuit for your tool. This circuit must not be less than a 12-gauge wire and should
be protected with a 15A time-delayed fuse. Before connecting the motor to the power line, make sure the switch
is in the OFF position and the electric current is rated the same as the current stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
Fig. 1
your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheat-
ing. The table below shows the correct size to be used according to cord length and ampere rating. When in doubt,
use a heavier cord. The smaller the gauge number, the heavier the cord.

UNPACKING
With the help of a friend or trustworthy foe, carefully remove the band saw from the packaging. Make sure to take
out all contents and accessories. Do not discard the packaging until everything is removed. Check the packing list
below to make sure you have all of the parts and accessories. If any part is missing or broken, please contact our
customer service at 1-800-232-1195 (M-F 8-5 CST), or email [email protected].
UNPACKING & PACKING LIST
WARNING! Do not plug in or turn on the tool until it is fully assembled according to the instructions. Failure
to follow the safety instructions may result in serious personal injury.
9
PACKING LIST
1. Band Saw (1)
2. Guide Rail (1)
3. Table with Insert (1)
4. Rip fence (1)
5. Short Brace (2)
6. Leg (4)
7. Long Brace (2)
8. Miter Gauge (1)
9. Accessory Tools (1)
10. Knob (4)
11. Hook with Hex Nut (1)
12. Push Stick (1)
Hardware Bag (Not Shown):
17. M8x12 Socket Head Bolts (8)
18. 8mm Flat Washers (12)
18. M6x12 Carriage Bolts (8)
20. 6mm Flat Washers (8)
21. M6 Hex Nut (8)
22. M4x10 Socket Head Bolts (2)
Circle Cutting Accessories:
13. Sliding Bracket
14. Center Pin
15. Lock Knob A
16. Lock Knob B
Tools Required for Assembly & Adjustments
The tools listed below are not included but are required for either assembly or adjustment.
• Two 13mm Open End Wrenches
• One Phillips Head Screw Driver
• One Combination Square
12
2
8
10
9
5
7
6
4
11 12
13
14
1615

10
KNOW YOUR BAND SAW
TOOL PURPOSE
Band saws are used to cut wood. Refer to the following diagrams to become familiarized with all the parts and
controls of your band saw. The components will be referred to later in the manual for assembly and operation
instructions.
10
Tension Knob
Light Switch
Power Switch
Locking Fence
Fence Lock
Dust Collection Drawer
Upper Housing Knob
Blade Guard Adjustment Knob
Blade Guard
Blade Bearing Adjustment Knob
Blade Tension Adjustment Knob
Lower Housing Knob
Miter Gauge
Tension Release Lever
Blade Tracking Adjustment Knob
Table Bevel Lock
Lower Spindle Tracking Adjustment Knob
Dust Port Capacitor Box
Motor

ASSEMBLY & ADJUSTMENTS
11
WARNING! Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read
through and become familiarized with the following procedures of handling and adjusting your tool. Failure to
follow the safety instructions may result in serious personal injury.
TO ASSEMBLE THE STAND
1. Carefully place the band saw on its back as shown above (Fig.
2), either on the floor or on a workbench. Prop the bottom of
the band saw up on a wooden block in order to have space to
assembly the band saw’s stand.
2. Attach legs to saw body using M8x12 socket head bolts and
8mm flat washers (Fig. 3).
3. Fix the short braces and the long braces by using M6x12
carriage bolts, 6mm flat washers and M6 hex nuts. DO NOT
TIGHTEN THE NUTS (Fig. 4).
4. Place the band saw upright and tighten all nuts. Make sure
there is no wobbling or tilting in the stand after fully tightening
the nuts.
TO ASSEMBLE THE TABLE
1. After attaching the stand, assemble the table to the bandsaw
by using M8x10 socket head bolts and 8mm flat washers (Fig.
5).
2. Make sure the saw blade is in the center of the table insert
slot.
3. Install the guide rail, securing it with the four knobs to the
table (Fig. 6).
Fig. 2
Fig. 3
Fig. 4
Fig. 5 Fig. 6

12
ASSEMBLY & ADJUSTMENTS
WARNING! Do not plug in or turn on the tool until it is fully assembled according to the instructions. Read
through and become familiarized with the following procedures of handling and adjusting your tool. Failure to
follow the safety instructions may result in serious personal injury.
INSTALLING THE ACCESSORY TOOLS
1. Install the accessory tools assembly to the frame by
using M4x10 socket heat bolts (Fig. 7 - 1).
2. Secure the hook with a hex nut to the frame (Fig.
7 - 2).
3. Set the rip fence onto the table. Lock it in place with
the Fence Lock (Fig. 8 - 1).
NOTE: To reverse the rip fence, remove the fence from
the rip fence by loosening the four bolts holding it to
the rip fence, reversing the fence, and reattaching the
bolts. (Fig. 9)
4. Set the miter gauge into the onboard storage along
the base of the bandsaw (Fig. 8 - 2).
5. Set the push stick on the hook (Fig. 8 - 3, Fig. 7 - 2).
INSTALLING THE CIRCLE CUTTING GUIDE
1. Insert the center pin into the hole of the sliding
bracket. Fix it with Lock Knob A. This center pin will
serve as the pivot point for making circular cuts (Fig.
10).
2. Fix the sliding bar into the bearing bracket of the up-
per guard assembly. Slide it into the desired position
and secure it with tightening Lock Knob B (Fig. 11).
Fig. 7
Fig. 8
Fig. 9
Fig. 10 Fig. 11
2
1
1
2
3
Lock Knob A
Lock Knob B

13
ASSEMBLY & ADJUSTMENTS
WARNING! Always be sure that the tool is switched off and unplugged before making any adjustments.
TILTING THE TABLE
1. Find and loosen the table bevel lock located in back under the
saw table (Fig. 12 - 1).
2. Adjust the table to the desired angle using the table tilting knob
(Fig. 12 - 2) and the angle indicator (Fig. 12 - 3).
3. Use the angle indicator to confirm the desired angle and tighten
the lock handle.
NOTE: A table perpendicular (90°) to the blade corresponds to a
scale indication of 0°).
ADJUSTING THE SAW BLADE
If the blade does not run in the middle of the rubber tire band, the
tracking needs to be corrected by adjusting the tilt of the upper
band saw wheel.
1. Turn of the bandsaw and unplug it from the power supply. Open
both the upper and lower wheel covers once the blade has stopped
moving (Fig. 13).
2. Loosen the tracking lock knob (Fig. 14 - 1) and manually rotate
the upper wheel, making sure not to touch the blade. Watch to see
which direction the blade tends to veer off towards in order to best
adjust the tracking set knob to resolve the problem.
3. Turn tracking set knob (Fig. 14 - 2) in the desired direction until
the blade is centered over the upper and lower wheels. Spin the
wheel manually to ensure that the blade is now running in the cen-
ter.
4. Tighten the tracking lock knob and close the covers (Fig. 14 - 1).
Fig. 12
1
2
3
Fig. 13
Fig. 14
12

14
ASSEMBLY & ADJUSTMENTS
WARNING! If the tension in the blade is too high, it runs the risk of breaking. If the tension is too low, there
is a risk of the blade slipping and stopping during a cut.
ADJUSTING BLADE TENSION
1. Raise the upper blade guide fully using the saw blade tension
knob located on the top of the machine (Fig. 15 - 1). Take the blade
width into consideration during the adjustment.
2. Check the tension by pushing with a finger against the side
of the blade halfway between the table and the upper guide. The
blade should not flex more than 2 mm.
3. Check the adjustment using the blade tension indicator on the
inside of the upper housing. The scale indicates the correct adjust-
ment for a certain width of blade. The indicator should be pointing
towards the width of blade being used.
4. Turning the setting knob clockwise increases the blade tension
while turning the setting knob counterclockwise decreases ten-
sion.
5. After achieving the desired tension, the tension release lever can
be used to easily loosen and tighten the spindles without changing
the amount of tension (Fig. 15 - 2).
ADJUSTING THE BLADE TENSION INDICATOR
The blade tension indicator can be adjusted for blades known to
be cut over or under length by different manufacturers. With mod-
erate tension on the blade, loosen the set screw (Fig. 16 - 1) and
adjust the blade indicator up or down as needed. Retighten the set
screw.
UPPER BLADE GUIDE ADJUSTMENT
Fig. 15
1
2
The height of the upper blade guard should be adjusted prior to every operation to accommodate the height of
the workpiece (the blade guard should be no more than one-fifth of an inch (3mm) from the upper edge of the
workpiece).
1. Use the adjustment knob (Fig. 17 - 1) to adjust the height of the upper blade guide. Use the outer locking knob
to secure the guard in place when it has reached the desired height.
2. Loosen the knobs on the side of the blade guard (Fig. 17 - 2 and 17 - 3) and adjust both the thrust and guide
bearings so that they are positioned approximately 1/10 of one inch (2mm) or less (0.5mm for the guide bearing)
away from the blade. The inside knob (Fig. 17 - 3) adjusts the thrust bearing, holding the back of the blade in place.
The outside knob (Fig. 17 - 2) adjusts the guide bearings, moving the blade left and right.
3. Once desired adjustments have been achieved (when the bearings are all roughly 0.1 to 0.5 mm away from the
blade) (Fig. 18, Fig. 19), tighten the knobs to secure the bearing guides in place.
Fig. 16
1

15
ASSEMBLY & ADJUSTMENTS
Fig. 17 Fig. 18 Fig. 19
WARNING! The lower blade guide must be adjusted
after every blade change and tracking adjustment.
LOWER BLADE GUIDE ADJUSTMENT
1. Loosen the set screw (Fig. 20 - 3) and move the entire lower
blade guide. Adjust the guide bearing to a position of 1 to 2
mm from the bottom of the blade. Retighten the set screw (Fig.
20 - 3).
2. Loosen the socket head bolt (Fig. 20 - 1) and adjust the
thrust bearing a position of .5 mm from the rear of the blade.
Retighten the bolt (Fig. 20 - 1).
3. Loosen the bolt (Fig. 20 - 2) and adjust the guide bearing to
a position .5 mm away from the blade. Retighten the bolt (Fig.
20 - 2).
Fig. 20
2
1
3
ADJUSTING THE CUTTING SPEED
1. Open the lower cover. Slacken the driving belt (Fig. 22) by turning the drive belt tension setting knob (Fig. 23 - 1)
clockwise.
2. Place the driving belt on the desired speed settings (Fig. 21) and retighten the drive belt tension setting knob.
Fig. 21 Fig. 22 Fig. 23
1
1
3
2

16
ASSEMBLY & ADJUSTMENTS
WARNING! The saw blade is dangerous. Be sure to wear gloves when handling the saw blade in any
situation.
CHANGING THE BAND SAW BLADE
1. Loosen the four lock knobs for the guide rail. Remove the guard rail by loosening the four lock knobs located
underneath (Fig. 24 - 1).
2. Open the upper cover and the lower cover. Set the upper blade guide to its lowest position.
3. Loosen the quick release lever until the bandsaw blade has sufficient enough slack.
4. Remove the bandsaw blade from the machine. Fit a fresh bandsaw blade and center the bandsaw blade on the
rubber tracking on each of the bandsaw wheels.
5. Tighten the quick release lever. After manually spinning the wheels to make sure the blade has been centered
properly, replace the guide rail to its original lever and close the upper and lower cover.
6. Align the saw blade, adjust the blade tension and adjust the upper and lower blade guides before operation.
Fig. 24 Fig. 25 Fig. 26
1

17
OPERATION
WARNINGS & SUGGESTIONS
• Do not touch the saw blade when cutting.
• During saw operation, wear safety glasses but do not wear gloves.
• Cut only one workpiece at a time.
• Always hold the workpiece down on the table.
• Do not jam any workpieces.
• Do not try to slow the blade down by pushing the work piece against the saw blade from the side.
• When straight cutting against the fence, use a push stick.
• Use a work support when cutting long stock to avoid pieces from falling down after the cut has been
completed.
• Use a dust collector and regularly empty the dust collection drawer.
• When cutting round stock, make sure the piece is a secure as possible.
• Before starting, check that the saw blade and the upper and lower blade guides are in proper working order.
• Replace damaged parts immediately.
• Assume the correct working position (the blade’s teeth should be pointing towards the operator).
• Take all necessary precautions to avoid kickback during operation.
Fig. 27
ON/OFF SWITCH
1. To turn the saw ON, move the switch to the up position (Fig. 27 - 1).
2. To turn the saw OFF, move the switch to the down (OFF) position.
3. To lock the switch in the OFF position:
a) Wait until the band saw has come to a complete stop.
b) Remove the safety key from the switch housing. Store the safety key in
a safe place.
4. To unlock the switch and turn the saw ON, insert the safety key into the switch,
and move the switch to the ON position.
2
1
LED WORK LIGHT
The work light switch is independent and may be turned ON or OFF separately from the band saw switch. The LED
switch is a smaller switch located directly above the main ON/OFF switch (Fig. 27 - 2).
REVERSING THE RIP FENCE
The rip fence can be used on both sides of the blade. When the
rip fence is to be moved from one side of the saw blade to the
other, the fence needs to be reversed using the following steps:
1. Loosen and remove the two knobs (Fig. 28 - 1).
2. Take off the fence with bolts from the fence support.
3. Assemble fence with bolts to the other side of fence support.
4. Replace the two knobs.
To change the height of the fence, loosen the two knobs, slide the fence out from the fence support, rotate the fence
90°, insert the lock screw into the other groove of the fence, and finally retighten the two knobs.
The fence can be adjusted parallel with the side of the blade by loosening the two socket bolts (Fig. 28 - 2)
Fig. 28
1
2

OPERATION
USING THE MITER GAUGE
1. Place the miter gauge into the slot on the table. (Fig. 29)
2. Loosen the knob on the gauge to set a new miter angle (be-
tween 0 and 60 degrees).
3. Tighten the knob firmly before cutting begins.
USING THE PUSH STICK
The push stick serves as an extension of the hand and protects
against accidental contact with the saw blade. The push stick
must be used if the distance between the bandsaw blade and the
rip fence is less than 5.9 inches. When the push stick is not used,
it can be stored on the hook provided on the bandsaw frame (Fig.
31). Replace the push stick if damaged.
GENERAL CUTTING
Fig. 29
Fig. 30
Fig. 31
WARNING! Operating a band saw involves a certain
amount of hazard. Read the instructions and plan your work
before cutting a workpiece.
1. Use scrap lumber to check the settings and to get the feel of
operating the band saw before attempting regular work.
2. Do not turn the power on before all adjustments have been
made. Check to make sure the upper guard is in place. Always
keep the upper blade guard close to your work, approximately
1/8” (3.2 mm) above the workpiece.
3. Do not force the workpiece against the blade. Light contact
permits easier cutting and prevents unwanted friction and heat-
ing of the blade. Sharp saw blades need little pressure for cutting.
Steadily move the workpiece against the blade without forcing it.
4. It is recommended that a dust collection bag be connected to
the dust port when sawing wood.
5. Use the band saw for straight line operations such as cross-cutting, ripping, miter cutting, beveling, compound
cutting, and resawing.
6. To avoid twisting the blade, do not turn sharp corners; instead, saw around corners. A band saw is basically a
“curve-cutting” saw. It is not capable of doing intricate inside cutting as can be done with a scroll saw.
WARNING! Do not use this band saw to cut ferrous metals.
18

OPERATION
CONNECT A DUST COLLECTOR
The band saw provides a dust port for collecting
various size hoses. It should be connected with a
dust collector during any sawing operations. Ex-
cess debris gets collected into the dust drawer un-
derneath which should be routinely cleaned out.
Dust port sizes include 1-3/4 inches, 2-3/4 inches,
and 3-3/4 inches.
Fig. 32 Fig. 33
Blade Width 1/8 in. 3/16 in. 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in.
Minimum Radius 3/16 in. 5/16 in. 5/8 in. 1-1/2 in. 2-1/2 in. 5-1/2 in. 7 in.
CUTTING CURVES WITH THE CIRCLE CUTTING GUIDE
To make a circular cut, use as narrow of a saw blade as is necessary for the radius of the circle.
1. Draw a circle and its center point on the
wood workpiece (Fig. 34).
2. Set the fence to the desired position where
the saw blade is in line to the tangent of the cir-
cle mark, keeping the wood work piece guided
by the fence. Turn on the bandsaw and cut off
the workpiece (Fig. 34).
3. Put the remainder of the workpiece with the
circle mark onto the table. Align the point of
tangency to the saw blade teeth. Set the center
pin in the center of the circle, fixing it in place
with the tightening knob (Fig. 35 - 1). Turn on
the bandsaw, slowly rotate and feed the work-
piece into the saw blade.
4. Aside from circles, this cutting accessory
can also help you easily cut out round corners
(Fig. 36).
Fig. 34 Fig. 35
Fig. 36
1
19

2120
ROUTINE INSPECTION
Before each use, inspect the general condition of the
tool. If any of these following conditions exist, do not
use until parts are replaced or the saw is properly re-
paired.
Check for:
• Loose hardware,
• Misalignment or binding of moving parts,
• Damaged cord/electrical wiring,
• Cracked or broken parts, and
• Any other condition that may affect its safe operation.
CLEANING & STORAGE
1. Keep the ventilation openings free from dust and
debris to prevent the motor from overheating. NOTE:
Always use a dust collection system. This will help pre-
vent sawdust from building up inside the band saw.
2. Wipe the tool surfaces clean with a clean cloth. Make
sure water does not get into the tool. Remove any pitch,
sap, or resin that has accumulated on the table, blade
guide, bearings, etc. using a damp cloth.
MAINTENANCE
WARNING! To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning,
adjusting, or performing any maintenance work.
WARNING! Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the
tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts.
Use of other parts may be hazardous or induce product failure.
CAUTION! Most plastics are susceptible to dam-
age from various types of commercial solvents. Do
not use any solvents or cleaning products that could
damage the plastic parts. Some of these include but
are not limited to: gasoline, carbon tetrachloride,
chlorinated cleaning solvents, and household deter-
gents that contain ammonia.
4. At least once a month, check the V-belt for proper
tension and any signs of wear.
5. Store the tool in a clean and dry place away from the
reach of children. Store in temperatures between 41° to
86°F.
6. Cover the band saw in order to protect it from dust
and moisture. Keep the instruction manual and all ac-
cessories nearby.
7. If you do not plan to use the band saw for a long pe-
riod of time (over 1 week), release tension on the blade.
This will help prolong blade life.
LUBRICATION
1. As needed, apply a light coat of good-quality paste
wax to the table. This will help provide a smooth gliding
surface for your workpieces.
2. As needed, apply a light coat of dry lubricant (PTFE
works well) to the space between the table bevel brack-
ets and the base bracket. This will help ensure that the
table bevels easily.
3. The bearings on your band saw are permanently
sealed and lubricated, and require no additional lubrica-
tion.
PRODUCT DISPOSAL
Used power tools should not be disposed of together
with household waste. This product contains electronic
components that should be recycled. Please take this
product to your local recycling facility for responsible
disposal and to minimize its environmental impact.
Please recycle the packaging and electronic
components where facilities exist.
3. At least once a month, open the doors and vacuum
out any accumulated dust, shavings, etc. Remove the
blade and clean off any built-up sawdust from the
wheels and tires using a stiff brush.