Wenger Conductor’s Podium User manual

Important User Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
General �����������������������������������������2
Manufacturer �������������������������������������2
Intended Use�������������������������������������2
Warranty ����������������������������������������2
Safety Precautions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 2
Assembly� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3
Operation� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4
Set Up ������������������������������������������4
Take Down� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Replacement Parts List � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8
Owner’s Manual
Conductor’s Podium
©Wenger Corporation 2019 Printed in USA 2019-08 Part #158E006-03
Wenger Corporation, 555 Park Drive, P�O� Box 448, Owatonna, Minnesota 55060-0448
Questions? Call�����USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp�com
Contents
Note: Please read and understand these instructions before assembly or use�
Note: Remove all items from the shipping cartons and arrange them in a convenient location�
Refer to the illustrations on the following pages� If you need additional information,
contact the Wenger Corporation using the information below�

2
Important User Information
General
Copyright © 2019 by Wenger Corporation
All rights reserved� No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's
personal use�
Printed and bound in the United States of America�
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation� Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions�
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions�
The manufacturer reserves the right to change this product at any time�
The information in this document is not intended to cover all possible conditions and situations that might occur�
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products� If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide�
Manufacturer
The Conductor’s Podium is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp�com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity conditions
— it must not be exposed to outside weather conditions�
· This product is intended to be assembled only as described in these instructions�
Warranty
This product is guaranteed free of defects in materials and workmanship for ve full years from date
of shipment� A full warranty statement is available upon request�
Safety Precautions
Throughout this document you may nd cautions and warnings which are dened as follows:
• WARNING: Failure to follow the instruction could result in serious injury or damage to property�
• CAUTION: Failure to follow the instruction could result in minor injury or damage to property�
Read all of these safety instructions before using the equipment�
Make sure that anyone working
with the Conductor’s Podium
has read and understands these
instructions.
!CAUTION
Failure to comply with the
Warnings and Cautions in this
document can result in damage
to property or serious injury.
!CAUTION

3
Assembly
1� Insert a 1" x 14-20 plug (7) into both open ends of the back railing (5)�
2� Lay the back railing onto the carpeted surface of the upper podium�
Align the pilot holes in the back railing with the slots in the mounting brackets�
3� Secure the back railing to both mounting brackets using one round retainer pin (6) in each side�
1" x 14-20
Plug
(7)
Align holes
Back Railing
(5)
Round
Retainer Pin
(6)
Round
Retainer Pin
(6)
Align holes

4
Operation
Set Up
1� With both podiums upright on the wheels,
roll them near the performance location�
2� Lower the clamp at the bottom of the upper podium�
Right Step Configuration Left Step Configuration
The Conductor’s Podium can be set up for either right step or left step conguration.
3. Lay the base podium at on the ground with the
carpeted surface facing up�
4� Place the upper podium onto the base podium
in either the left step or right step conguration.
The upper podium must align with the
base podium.
Lower
clamp
Base
Podium
Upper
Podium

6� Raise the back railing�
a� Tip the back railing up to be vertical�
b� Drop the railing ends into the
mounting brackets�
5
Podium can tip unless clamp
securely engages base.
!CAUTION
Operation (continued)
Set Up (continued)
5� Connect the upper podium clamp to the base podium�
a� Lift up the back of the upper podium and
push the front of the podium forward
to engage the clamp to the base podium�
b� Lower the upper podium onto the base podium�
c� Be certain that the clamp is secure.
Engage
clamp
Drop railing end into
mounting bracket
Tip up and
drop down
Front of
podium
Back of
podium
Engage
clamp

6
Take Down
1� Lower the back railing�
a� Lift the railing ends out of the
mounting brackets�
b� Tip the back railing down to rest on the
upper podium�
Operation (continued)
Lift railing end out
of mounting bracket
Lift up and
tip down
2� Disconnect the upper podium clamp from the base podium�
a� Lift up the back of the upper podium and
pull the front of the podium back
to disengage the clamp from the base podium�
b� Lower the upper podium onto the base podium�
Disengage
clamp
Front of
podium
Back of
podium
Disengage
clamp

7
Take Down (continued)
3. Lift the upper podium o󰀨 of the base podium and
tip both podiums onto the wheels�
Operation (continued)
Base
Podium
Upper
Podium
4� Raise the clamp at the bottom of the upper podium�
5� Both podiums can now be rolled away�
Lower
clamp

8
Item Qty Description
11Base Podium Weldment
21Base Podium Top Assembly
31Upper Podium Weldment
41Upper Podium Top Assembly
51Back Railing
62Round Retainer Pin
721" x 14-20 Plug
865/16-18 x 1-1/2" Caspscrew
965/16" Helical Lock Washer
10 1 Clamp Assembly
11 1 Base Podium Support Tube
12 1 Upper Podium Support Tube
13 19 #14-10 x 3/4" Pan Head Screw
14 3 1/4" Lock Washer
15 16 Rubber Bumper
16 32 #6-18 x 1/2" Flat Head Screw
17 4 4" Dia Wheel
18 4 Podium Wheel Axle
19 8 Steel Cable Strap
20 16 1/4-20 x 1/2" Machine Screw
21 16 1/4-20 Lock Nut
22 2 Mounting Bracket Assembly
23 8 5/16-18 x 5/8" Capscrew
24 8 5/16-18 Flange Lock Nut
Replacement Parts List
1
3
2
4
5
6
7
8 9
10
11
12
13 14
13 14
15 16
15 16
17 18 19 20 21
8 9
17 18 19 20 21
22 23 24