WesAudio Timbre User manual

1
WESAUDIO
4/25/16
TIMBRE USER MANUAL
www.WesAudio.com
Timbre
User manual
EN
Copyright 2016 by WesAudio

2
WESAUDIO
4/25/16
TIMBRE USER MANUAL
Thank You for the purchase of Timbre
Timbre
All tube Vari-mu mono compressor.
With kind regards
Radoslaw Wesolowski

3
WESAUDIO
4/25/16
TIMBRE USER MANUAL
Table of Contents
1. Instalation.................................................................................................................................................5
2. Front Panel ...............................................................................................................................................6
3. Linking compressors.................................................................................................................................7
4. Maintenance ............................................................................................................................................7
5. Specifications............................................................................................................................................7
6. Warranty .............................................................................................. Błąd! Nie zdefiniowano zakładki.

4
WESAUDIO
4/25/16
TIMBRE USER MANUAL
As always It’s all about compression so we’ve created “Timbre” – an all
tube vari-mu compressor based on the 6386 tube, inspired by the old,
famous and much desired Gates STA-Level compressor. The Timbre is
easy to use, full of color and sweetness. It is a vintage-style compressor
made from the highest quality of components.
Augmenting the design, we have added new features like the third
mode of operation with shorter attack time, a high-pass sidechain filter,
a link for stereo operation and a bypass function. Timbre utilizes a
novel programme controlled release circuit which creates density and
consistency while minimizing typical compressor side-effects at up to
40dB of gain reduction!

5
WESAUDIO
4/25/16
TIMBRE USER MANUAL
1. Installation
The unit comes in a 2U form. As it can produce large amount of heat during long
work, it is advised to leave at least 0.5U space above it to dissipate the heat and
should be placed in a ventilated rack cabinet. It is recommended to switch ON
device at least 15 minutes before operating to ensures best parameters.
Warning !!!
High Voltage inside !
!!! The device should be connected only to a grounded outlet
and proper voltage !!!
To reduce the risk of electrical shock do not open the unit.
Always replace the fuse with the type and value recommended by manufacturer:
230V –IEC 127 20x5mm T315ma
115V –IEC 127 20x5mm T630ma

6
WESAUDIO
4/25/16
TIMBRE USER MANUAL
2. Front Panel
1 2 3 4 5 6 7 8
1. Input –determines the level of the input signal entering the Timbre, as well as the threshold.
Higher settings will increase amounts of compression or limiting.
2. Mode- provides three distinct flavors of attack & recovery characteristic.
SINGLE –Provides a simple slow attack that is very smooth.
DOUBLE –Provides an intelligent program-controlled attack and release characteristic that brings up
density and detail without pumping like traditional compressors.
TRIPLE- Provides the program-controlled characteristic with extra fast attack, for maximum density.
It is only recommended with small amounts of gain reduction.
3. Recovery –gives six release times. The first (left) position is the standard slow release time. Each
click to the right is progressively faster.
4. S.C FILTER –enables high-pass side chain filter in the detector chain which makes compressor
less sensitive in low frequency band.
5. Comp IN –engage the compressor, when switch is in the off position signal is hard bypassed by
relay.
6. Link –enables link function when you want to connect two units together (more info in Linking
compressors section).
7. Output –determines the level of the output signal. Is is used to recover compression lost signal.
8. Power- main power switch.

7
WESAUDIO
4/25/16
TIMBRE USER MANUAL
3. Linking compressors
To link two compressors to work in stereo mode, you need simple Jack-Jack 6.3mm mono
cable. Just connect two compressors together with this cable and activate “Link”function
on both compressor. From now on both compressors will use common compression signal.
For proper operation in stereo mode, both compressors should have exactly the same
settings.
4.Maintenance
Compressor does not require any technical maintenance during the warranty period. Please
keep it in dry place free from any dust or moisture.
5. Specifications
Frequency response: 20Hz-30kHz (0.5dB)
THD+N: up to 1%
Input impedance: transformer balanced: 600ohm
Output impedance: transformer balanced: 600ohm
Tubes: 6386, 12AT7, 12AX7, EAA91
Max gain: 45dB
Max gain reduction : 40dB
Mode: single, double,triple
Balanced output and input (XLR Amphenol)
Case Rack 2U
Dimensions : 88 x 483 x 235 mm
Box dimensions : 55 x 39 x28 cm
Weight 7kg

8
WESAUDIO
4/25/16
TIMBRE USER MANUAL
Warranty
All WesAudio products are built to the highest standards and
should provide reliable performance for many years, subject to
reasonable care, use, transportation and storage.
WesAudio warrants all of our products to be free of defective
parts and workmanship for a period of two years. This warranty
period begins at the original date of purchase and is transferable
to any person who may subsequently purchase the product during
this time. This warranty excludes the following conditions: normal
wear and tear, misuse, customer negligence, accidental damage,
unauthorized repair or modification, cosmetic damage and
damage incurred during shipment. During the time of this
warranty, WesAudio will repair or replace, at its option, any
defective parts or repair defective workmanship without charge,
provided the customer has appropriate proof of purchase and
that the product has its original factory serial number. In all
warranty claims the customer is responsible for shipping costs to
the WesAudio facility, and WesAudio pays for return ground
shipping