Wessex HLS-100 User manual

REV A 17/11/15
Assembly Guide
Wessex Country Log Splitter HLS-100
Hydraulically Powered, Tractor Mounted

1 REV A
Tools Required
Spanner / Socket –17mm, 19mm, 24mm (2 of Each)
Screwdriver –Flat Head or Philips
Large Adjustable Spanner
1.
Install RHS upper body using the three bolts labelled above –Do Not Fully Tighten
(Note: One bolt is longer than the others and requires a full nut)
M12 X 130
M12 X 100
M12 X 100
Full Nut
Nyloc Nut
Nyloc Nut
Rear Brace
Front Brace
Log Pusher
Valve Block
Mount
Front Leg x2
Arc x2
Rear Leg x2
Frame
Upper x2
Control Leaver x2
Lower Link Pin
End Plate
Cover / Chute
Main Spine Assembly
Clamp Plate

2 REV A
2.
Attach the LHS Upper using the bolts labelled above
(Note: One bolt is longer than the others and requires a full nut)
Make sure that the 2 Upper Pieces are not over lapping. (Edges must meet before tightening bolts)
Fully tighten all top M12 Bolts
3.
Using 2x M10 X 35 Bolts connect the 2 rear legs as shown. Do Not Fully Tighten
Repeat for opposite side.
M12 X 130
M12 X 100
M12 X 100
Full Nut
2x Nyloc Nut
Nyloc Nut
Nyloc Nut
2x M10 X 35

3 REV A
4.
Connect the two Side Braces to the rear frame. Use 8x M10 X 35 bolts with washers and nyloc nuts.
Do Not Fully Tighten
Repeat for opposite side.
5.
Connect the green front legs with 2x M12 X 30 Bolts each side with washers and nyloc nuts. Do Not Fully Tighten
Repeat for opposite side.
4x M10 X 35
2x M10 X 35
2x M12 X 35

4 REV A
6.
Connect the front Upper Brace / Cover Pivot using 4x M12 X 90 Bolts with washers both sides and a nyloc nut.
Do Not Fully Tighten.
7.
Connect the Pusher Head to the end of the Hydraulic Ram using the M16x130 Bolt and Nyloc –Fully tighten. Then
place the assembly into the track and secure the end of the ram using the M20 x 130 Bolt and Nyloc Nut –Fully
Tighten
4x M12 X 90
4x Nyloc Nut
4x M16 X 130
Washers + Nyloc
4x M20 X 130
Washers + Nyloc

5 REV A
8.
Connect the valve block to the underside of the box section using two M12 nyloc nuts. The full nuts from steps 1 and
2 are used as spacers and must not be removed.
Fully Tighten
9.
Place the Handles through the slots in the Upper Frame and secure them with the M12 X 120 Bolt. Use 4 Washers
are shown (In between the handles to reduce friction.)
2x Nyloc Nut
4x M12 Washer

6 REV A
10.
Attach the Clamp Plate to the underside of the Log Pusher Assembly Using 2x M10 X 100 Bolts with Nyloc Nuts and
Washers –Fully Tighten
11.
Attach the front brace and secure with 2x M12 X 30 Bolts with Nyloc Nuts and Washers - Fully Tighten
2x M10 X 100
2x M12 X 30

7 REV A
12.
Attach the Rear Brace with the Bolt in Lower Link Pins that are provided. Use a Screw Driver in the hole on the end of
the pin to stop the pin turning whilst tightening. Use a Large adjustable spanner to fully tighten the nut.
13.
Connect the Cover / Log Shute with the M10 x 20 Bolts. Use washers and Nyloc Nuts –Do Not over Tighten
14.
Work back through the assembly and fully tighten all bolts on steps 3,4, 5 and 6.
Make sure everything is tight before using the log splitter.
2x WX-2026
2x M10 X 20