WESTERSTRAND AUREA ALPHA User manual

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 1 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Manual
AUREA ALPHA
Art. no: 119425-10

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 2 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
General
This product is a digital clock for indoor use. The digital clock can be used as a quartz clock, via radio signal
(DCF/RDS) or via impulse from a master clock (sync). The clock is changing, summer and winter time, the
last Sunday in March and the last Sunday in October automatically.
The Digital clock can be programmed for alternating time/temperature display in 0-25 sec intervals.
Temperature sensor is not included. It is an option.
The clock has adjustable light intensity.
If power failure occurs the display is turned off. The internal clock continues to keep the correct time
for 48 hours. After power failure the display is turned on and correct time is shown.
If not specified in order the clocks are preset from factory in impulse Synchronisation mode.
Options
For connection of the options look at the special manuals of the options.
Following options is available:
•Radio receiver DCF
•Radio receiver RDS
•IRIG-B –input (factory mounted option)

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 3 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Installation
General
The digital clock consists of two parts: the mounting plate and the clock. All the connections are made
to the mounting plate.
Figure. Mounting plate
The holes in each corner on the mounting plate are used to fasten the mounting plate on the wall.
The power (230VAC, 50Hz) is connected to a screw terminal, which is mounted on the mounting
plate.
Fuse: 10A max
Cable area: 1,5mm²
If the digital clock will be connected to a synchronisation source, it will be connected to the computer
board on the mounting plate. See Connection synchronisation wire, page 4.

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 4 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Connection Synchronisation wire
TC/MIN-imp 3,4
DCF 2-line 3 – V+, 5 – GND
DCF 3-line 3 – V+,4- DCF, 5 – GND
Sync. input
12345

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 5 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Strapping/DIP switch setting for TC / MIN-impulse (default)
Strapping/DIP switch setting for DCF-radio (2 –wire) computer board

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 6 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Strapping/DIP switch setting for DCF-radio (3 –wire) computer board
The DIP-switch on the computer board should be set as follows:
Dip 1: OFF Display format is HH:MM.
ON Display format is HH:MM:SS.
Dip 2: OFF always OFF
Dip 3: OFF TC/Min impulse synchronisation. (default)
ON DCF synchronisation.
Dip 4: OFF TC/Min impulse or 3-wire DCF synchronisation. (default)
ON 2-wire DCF synchronisation.
Dip 5: OFF DCF synchronisation.
ON TC/Min impulse synchronisation.(default)
Dip 6: OFF ½ Min impulse synchronisation.
ON TC/Min impulse synchronisation or DCF synchronisation. (default)
Dip 7: OFF always OFF
Dip 8: OFF always OFF

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 7 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Synchronisation
Stand alone
If the clock does not have an external synchronisation, it operates Stand alone.
Minute impulse
Make the strapping according to the drawing for strapping page 5.
Connect the minute impulse wire according to the schema page 4.
The clock can be set in synchronisation or slave mode.
Synchronisation mode:
Set the clock for synchronisation, mode InSy See programming page 9.
Set time and wait for next minute impulse. The clock will be synchronised
Slave mode:
Set the clock for slave, mode InSL See programming page 9.
Set time and wait for next minute impulse. The clock operates as a slave clock.
TC
Check the strapping according to the drawing for strapping page 5.
Connect the TC wire according to the schema page 4.
Set the clock for synchronisation, function DCF See programming page 9.
When a correct time message appears the clock sets the time.
The clock will blink colon when it is in sync and accepts transmitted code.
DCF
Check the strapping according to the drawing for strapping page 5.
Connect the DCF wire according to the schema page 4.
Set the clock for synchronisation, function DCF See programming page 9.
When a correct time message appears, the clock sets the time.
The clock will blink colon when it is in sync and accepts transmitted code.

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 8 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Connection temperature sensor (this is an option).
Temperature sensor connection
1 red.
2 black
5 Screen
12345

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 9 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Programming
General
On the right side of the digital clock there are three buttons (Figure Placement of the buttons). When
the `R` button is pressed the digital clock gets back to the basic state (the time is displayed on the
digital clock). The buttons ´F´ and ´P´ is used for programming.
Figure. Placement of the buttons
R (Return) Enter the base mode (display time)
F (Function)Next function / Accept displayed value
P (Program)Enter the displayed function / Increase displayed value.
Programming time
Push [F] until display shows
Push [P] display shows year.
Push [P] until desired year (00-99)
Accept with [F].
Display shows month.
Push [P] until desired month (1-12).
Accept with [F].
Display shows day.
Push [P] until desired date (1-31).
Accept with [F].
TI ME
YY 95
MO 1
DD 19

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 10 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Display shows hour.
Push [P] until desired hour (0-23). Accept with [F].
Display shows minutes.
Push [P] until desired minute (00-59). Push [F] for synchronisation and the clock starts
Display shows:
Push [R]. The Programming is finished.
Display shows:
Setting light intensity
The light intensity for the digits can be adjusted in 8 levels.
An automatic dimmer function regulates the light intensity.
Push [F] until display shows.
Push [P]
Display shows: . Light intensity 1 (weakest), 8 (strongest).
Push [P] for desired light intensity. Accept with [F].
Display shows
Push [R] for entering base mode or push [F] for next function.
HH 12
MM 00
TI ME
12: 00:00
DI SP
DI 1
SY NC

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 11 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Setting synchronisation
Synchronisation for this model are minute impulse, TC, DCF (or stand alone).
Push [F] until display shows.
Push [P] until desired synchronisation.
No synchronisation, stand alone.
TC or DCF.
Impulse synchronisation.
Impulse slave.
Push [R] for entering base mode or push [F] for next function.
Setting alternating time, Loop time
Push [F] until display shows.
Push [P].
Display shows Alternating time for display time is 4 seconds.
Push [P] for desired alternating time (0-25). Accept with [F].
Display shows Alternating time for display temperature is 0
seconds.
Push [P] for desired alternating temperature (0-25). Accept with [F].
Push [R] for entering base mode or push [F] for next function.
SY NC
NO SY
DCF
IN SY
IN SL
LO OP
L1 4
L2 0

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 12 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Setting Correction value for the temperature sensors.
With this function the temperature sensors can be adjusted ±9 ˚C.
Push [F] until display shows.
Push [P].
Display shows
Push [P] for desired correction value (±9 ˚C). Accept with [F].
Push [R] for entering base mode or push [F] for next function.
Setting Language-function.
With this function the display language can be choosed.
Push [F] until display shows.
Push [P].
Display shows (FL = Flemish, FR = frensch, DE = german,
FI = Finish, SV = Swedish, NO = Norwegian,
DK = Danish, EN = English)
Push [P] for desired language.
Push [R] for entering base mode or push [F] for next function.
CO RR
C1 0
LA
FL

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 13 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Setting nation-function. (for the dls rules)
With this function the nation can be choosed.
Push [F] until display shows.
Push [P].
Display shows (B = Belgium, F = France, D = Germany,
SF = Finland, S = Sweden, N = Norway,
DK = Denmark, GB = England, ND = NO DST)
Push [P] for desired nation.
Push [R] for entering base mode or push [F] for next function.
Setting12/24 h format.
With this function the format 12/24 hours display can be set.
Push [F] until display shows.
Push [P].
Display shows 12 hour format.
or
24 hour format.
Push [P] for desired format.
Push [R] for entering base mode or push [F] for next function.
NA
B
FO RM
12
24

Document: 1976en03.doc
WESTERSTRAND
Author: TAn
Date: 2015-11-10
Page: 14 of 14
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Technical specification
Data 119425-10
Main power 100-240V AC
Connection current 2 A
Temperature range 0˚- +40˚ C
Size of digits 58 mm
Diode colour Green
Diod light intensity 300mcd
Power consumption
(impulse) 5 mA
Synchronisation Polarised 24V impulse 1/1, ½ min*
Radio signal DCF**, RDS**
Time code via IRIG-B***
Running reserve 72 hours
Accuracy 0,1 sec/24 h quartz operation
Protection class IP43
Standards compliance EN50081-01 och EN50082-02
Weight 3,3 kg
Dimensions 520 x 295 x 75 mm
*Sync. The clock will continue if the impulse disappears.
** Option
*** Factory mounted option