WESTERSTRAND LUMEX 7 User manual

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 1 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Digital Clock ...........................................................................................................................................................1
User Manual ............................................................................................................................................................1
General ................................................................................................................................................................2
Installation ...........................................................................................................................................................2
Synchronisation ...................................................................................................................................................5
NTP .....................................................................................................................................................................5
Stand alone ..........................................................................................................................................................5
Configuration using R F P buttons ......................................................................................................................6
Configuration using a WEB browser...................................................................................................................9
Firmware Download / Wunser ..........................................................................................................................22
Reset Button ......................................................................................................................................................22
Technical specification......................................................................................................................................23
Abbreviations ....................................................................................................................................................24
User Manual
Digital Clock
LUMEX 7 NTP PoE

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 2 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
General
LUMEX 7 is a Digital Clock for indoor use, displaying time in hours, minutes and seconds. The time can be
displayed in either 12 or 24 hour format. The clock can also be configured to show the time and date alternately.
The digits are built using discrete LEDs forming 7-segment digits with a reading distance of 25m.The light
intensity of the digits is adjustable by an automatic dimmer control.
The clock is prepared for time synchronization by Network Time Protocol (NTP) from a NTP server. If the
connection to the NTP server is lost the clock will continue to run on the built in time base.
Configuration of network settings, light intensity and other parameters is done via a WEB-browser. Some of
the parameters can also be set using three buttons located at the right side of the clock.
The factory default setting for the IP address assignment is DHCP with foldback IP address 192.168.3.10
Please note, if default settings are used no configuration is needed.
The clock is powered by Power over Ethernet (PoE). In case of power failure the display is turned off but the
built in real time clock will continue to run for 48 hours. When the power is restored it will resynchronize
automatically.
Installation
Always disconnect power from the clock before installation or service!
The digital clock is delivered with an installation kit packed in a separate plastic bag.
The delivery consists of the following parts:
1 Digital Clock
1 plastic bag containing the following:
4 pcs. black cover plug
2 pcs. cable gland
2 pcs. strain relief
4 pcs. screw 4.2 x 16 mm
4 pcs. screw 4.2 x 22 mm
6 pcs screw 3 x 16 mm
1 User Manual.
•Disconnect the flat ribbon cable from the power supply
and put the front part aside until needed.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 3 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
15,5 100
131
14
346
318
4xØ5
•Decide which of the seven possible cable inlets that are going to be used for the network cable. Remove the
pre-punched plastic piece that is covering the cable inlet using a sharp knife or a drilling machine. The cable
gland requires a hole with diameter of 20.5 mm. Mount the cable glands. Make sure that the glands are
properly inserted.
•Mount the clock on the wall using 4 screws suitable for the wall material. Press the black cover plugs over
the screw heads. Make sure that the plugs are completely inserted.
•Connect the network cable. If needed mount the cable
strain relief using the enclosed screws. Use either 4.2 x
16 or 4.2 x 22 depending on the cable diameter.
•Connect the flat ribbon cable and assemble the front
part, using the 6 black screws.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 4 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Connection details
The connections are made at the back plate (see below.)
Terminal Description Remark
Network/PoE
input
10/100BASE-T.
PoE 802.3af.
Connector: RJ45
PoE Power consumption 15W max.
12V DC
input
Alternative power supply.
(if PoE is not available)
Connector: 2-polar 2,1 mm DC jack.
Cent
er +.
12V DC / 15W max.
LED indication
LED
Remark
LINK
Network Link/Act
Green = Link/Act OK
Black = No Link/Act.
STATUS NTP sync. status Green = Clock synchronised from
NTP server
Black = Clock is unsynchronised
POWER
Power indication
Green = P
ower OK
Black = No power
LINK LED
STATUS LED
POWER LED
RESET BUTTON
LINK LED
STATUS LED
POWER LED
RESET BU
TTON

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 5 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Synchronisation
NTP
The clock is prepared for time synchronization by Network Time Protocol (NTP) from a NTP server . When a
correct time message is received the clock will display correct time automatically.
The colon between hours and minutes will flash when the clock is in sync and the time message is
accepted.
Stand alone
If the clock does not have an external synchronisation, it operates standalone.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 6 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Configuration using R F P buttons
General
Configuration of network settings, light intensity and other parameters is done via a WEB-browser. Some of
the parameters can also be set using three buttons located at the right side of the clock.
Please note, if default settings are used no configuration is needed.
The programming is made with push buttons placed on the side of the clock (see below).
<= R
<= F
<= P
R (Return) Enter the base mode (Display time)
F (Function)Next function / Accept displayed value
P (Program) Enter the displayed function / Increase displayed value.
Keep button [P] in for quick scrolling.
Programming time
Push [F] until display shows
Push [P] display shows: year.
Push [P] until desired year (00-99)
Accept with [F].
Display shows: month.
Push [P] until desired month (1-12).
Accept with [F].
Display shows: day.
Push [P] until desired date (1-31).
Accept with [F].
Display shows: hour.
Push [P] until desired hour (0-23).
ti nE
yy 19
nn 1
dd 1
hh 12

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 7 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Accept with [F].
Display shows: minutes.
Push [P] until desired minute (00-59).
Push [F] for synchronisation and the clock starts.
Display shows:
Push [R]. The Programming is finished.
Display shows:
Setting light intensity
The light intensity for the digits can be adjusted in 8 levels.
An automatic dimmer function regulates the light intensity within each level.
Push [F] until display shows:
Push [P]
Display shows: Light intensity 1 (weakest), 8 (strongest).
Push [P] for desired light intensity.
Accept with [F].
Push [R] for entering base mode or push [F] for next function.
nn 07
ti nE
12 : 07 : 00
di SP
di 1

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 8 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
IP d
View / configure IP address
The Clocks IP address can be either static or dynamic (DHCP). Configuration of IP addressing work mode is
done using a web-browser. The default setting is DHCP.
Using the R F & P buttons it is possible to view or change the current IP-address. It is also possible to see if the
Clock is using static or dynamic IP address.
If the work mode is DHCP it is not possible to change the IP address manually.
To view the current IP address
Push [F] until display shows:
Push [P]
Display shows:
Push [F].
Push [F].
Push [F].
In this example the IP address is 192.168.2.51
Push [R] for entering base mode or push [F] for next function.
A 192
b 168
C 2
C 51
IP address work mode:
d = dynamic
S = static

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 9 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Configuration using a WEB browser
Login
It is possible to login as administrator or guest. The administrator has the rights to read and to write/change
configuration. A guest can read only.
User name
admin or guest.
Password
Enter a password. Default password is password.
Efter login visas en funktionsmeny:

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 10 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Status
Name
Symbolic name. The name
is set in function
General
UTC/LT
Current time
Timezone
Offset to UTC during normal time (=winter time).
IP
The Clocks
IP address
Net
mask
Shows the ne
tmask setting
Gateway
Shows the
IP address of the gateway
DNS
Shows the
IP address of the DNS server
MAC
A MAC address has format 00
-
07
-
09
-
xx
-
xx
-
xx
Alarms Shows if the Clocks has any alarms. The following alarm texts can be displayed.
No Alarms = Clock OK.
Not synchronised = The Clock is not synchronised.
5-minute limit = The received time message is more than 5 minutes wrong compared to
internal time. The message is not accepted.
Authentication
= The MD5 authentication has failed.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 11 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
NTP Synchronised = The clock has been synchronised from a NTP server with name/IP ntp.se
s = Stratum, time quality. A low value is better
n = Number of time settings from this NTP server
TO= Timeout in minutes before NTP alarm. The clock goes to 12:00.
Clock Clock [14:24] = Current data on display
Dimmer=7/8:Just now dimmer value 4. Maximum 8
Sensor=2
2808
: Current light sensor data 0
-
65535.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 12 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Network
Enter general network parameters

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 13 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
DHCP
Unchecked – Static IP address according to static IP below.
Checked – DHCP IP address with fallback according to IP fallback below.
Fallback
If DHCP is activated this will be the DHCP fallback address.
Static IP
To be checked if static IP address is used.
Address
Enter the static IP-address.
Subnetmask
Gateway
Gateway IP address.
DNS
IP address of DNS server. Two different addresses can be entered, DNS1 and DNS 2.
Utilities
Syslog
Syslog server IP address. Send syslog messages if checked.
Identity access
Identify access is used in combination with application software Wunser. Wunser is a PC program that is used
for finding and doing light configuration on Westerstrand Ethernet products. Firmware updates are also handled
by Wunser.
Wunser uses UDP port 9999 when communicating with other Westerstrand products and UDP port 69 when
downloading new firmware. These ports can be open, closed or prepared for encrypted communication.
Identify access = Normal ; port 9999 and port 69 is open.
Identify access = Password ; port 9999 and port 69 are using AES encryption. The password used is the same
as the administrator login password.
Identify access = Disabled ; port 9999 and port 69 is closed.
Telnet
Use of Telnet protocol allowed if checked.
Web server
Use of HTTP protocol (web-browser) allowed if checked.
HTTPS
Use of secure communication protocol HTTPS (web-browser) if checked.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 14 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
SNMP
This function is used to activate the SNMP, enter the address of one or more SNMP servers and to define the
SNMP community.
Trap address. The IP address can be specified as an IP address or as a full domain name. Up to three SNMP
server addresses can be entered.
Trap type
This function is used to choose SNMP trap version.
Trap type v1 = Trap according to SNMPv1
Trap type v2 = Trap according to SNMPv2
NTP
NTP settings
General description
When working as NTP Client the unit has three different ways to determine the most accurate and reliable
candidates to synchronize the system clock. Which model that is used depends on the specific installation and
the customer requirements. The NTP client has also a server list where up to 5 different time servers can be
entered.
The three different ways are:
1. FIRST Always use the first server in the list if available. If not available take next one.
This suits installations where it is more important to know exactly from where the clients get time than to have
the most accurate time. The other NTP servers in the list will then be more of backup servers.
2. STRATUM Use the NTP server with best stratum. The software sends a request to all servers in the list and
uses the time from the one with best stratum. If same stratum it will use the one that is first in the server list.
This suits installations where it is important that the time is coming from a time server high up in the pyramid.
3. MEDIAN Send a request to all servers in the list and use the median value (the NTP server that is in the
middle). This will filter out all misleading time messages.
In addition to these rules there are some more features such as synchronization limits and a special clock
discipline algorithm. This algorithm measures the oscillators drift over a longer period and makes
compensations for the drift.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 15 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
DHCP option 042
Ask for time using the server IP addresses received from the DHCP server (DHCP option 0042). Maximum 2
NTP servers are set automatically by option 0042.
Broadcast
Broadcast: Accept broadcast/multicast time messages. Broadcast address: 255.255.255.255

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 16 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Multicast
Accept multicast time messages. Multicast address: 224.0.1.1
NTP server
Select NTP servers, e.g. 192.168.1.237 or as an URL ntp.se. Also see NTP mode =DHCP above
Up to five different NTP servers can be entered.
Set local Time
Used for manual time setting.
Interval
Interval in seconds between NTP requests.
Remove time at alarm
This function is used to define how the clock should behave during a NTP synchronization alarm. See Alarm
timeout below. If the checkbox is checked the clock will show --:-- in case of synchronization alarm. If the box
is not checked, the clock continues to show time and uses its own built-in quartz oscillator as time reference.
Alarm timeout.
Time in minutes before the NTP synchronization alarm is activated.
Timezone
Select country/time zone. A NTP server sends UTC time. The clock will correct this to local time. If Daylight
Saving Time (see below) is checked it will also and adjust for DST (Daylight Saving Time) automatically.
Daylight Saving Time
If checked then this timezone uses DST (Daylight Saving Time).

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 17 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
NTP advanced
Advanced NTP settings
Client mode
FIRST. Always use the first server in the list if available. If not available take next one.
This suits installations where it is more important to know exactly from where the clients get time than to have
the most accurate time. The other NTP servers in the list will then be more of backup servers.
STRATUM. Use the NTP server with best stratum. The software sends a request to all servers in the list and
uses the time from the one with best stratum. If same stratum it will use the one that is first in the server list.
This suits installations where it is important that the time is coming from a time server high up in the pyramid.
MEDIAN. Send a request to all servers in the list and use the median value (the NTP server that is in the
middle). This will filter out all misleading time messages.
Only accept Stratum 1
This function makes it possible to synchronise to Stratum 1 time servers only.
Check box = Off ; synchronise to time server independent of stratum level.
Check box = On ; synchronise only if time server is operating on Stratum 1 level.
Authentication
If authentication is activated: Use MD5 authentication.
Server ID/Key: Authentication data for the external NTP servers configured in the NTP server list.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 18 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Clock
Used to configure general clock parameters.
Model
Clock model. This is set at delivery and should not be changed. For this product, “Lumex 5/ /12” must be
selected.
Leading zero
Time: not checked; " 8:29",checked; "08:29"
Date: not checked; " 7.9 ", checked "07.9 " (Sep 7)
12h clock
Show e.g. " 2:49" (12h clock) instead of "14.29" (24h clock)

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 19 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
Show Time
Loop-time in seconds for time
Show Date
Loop-time in seconds for date
Dimmer
Enter dimmer max value 1-8.
Light sensor
Allow for input from light sensor.
Current sensor value 0..65535 to the right.
Disable buttons
Disable buttons on the clock. When the buttons are locked the only thing that can be done using the buttons is to
read the IP-address.

WESTERSTRAND
Document: DOK18274en02
Author:
PM
Date: 2019 11 08
Page: 20 of 24
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE 545 23 TÖREBODA Fax. [phone] E mail: [email protected]
General
Used to configure general parameters.
Name
Symbolic name, maximum 64 characters. This name is shown in the status menu.
Use underscore ( _ ) between words.
Example: Digital_Clock_Front_Desk