WESTERSTRAND QWTIME III WDP M+S User manual

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 1 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
User Manual
Master Clock WDP M+S

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 2 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
List of contents
TECHNICAL SPECIFICATIONS...............................................................................................................................4
GENERAL DESCRIPTION .......................................................................................................................................5
INSTALLATION ........................................................................................................................................................6
CALCULATION OF CABLE AREA IN TIME SYSTEMS .................................................................................................................7
CONNECTION OF HOURLY CORRECTION (SR2/3) CLOCKS......................................................................................................8
SYNCHRONISATION INPUT .....................................................................................................................................................9
General............................................................................................................................................................................9
Synchronisation from another Master Clock...................................................................................................................9
SERIAL PORT RS232/RS485................................................................................................................................................10
General..........................................................................................................................................................................10
Connection via RS232....................................................................................................................................................10
Connection via RS485....................................................................................................................................................10
PROGRAMMING.....................................................................................................................................................11
GENERAL ............................................................................................................................................................................11
RUNNING MODE ..................................................................................................................................................................11
START UP ............................................................................................................................................................................12
SET TIME WHEN IN OPERATION............................................................................................................................................13
Summer to winter ( Day light saving )...........................................................................................................................13
SLAVE CLOCK .....................................................................................................................................................................14
ALARMS ..............................................................................................................................................................................15
Example 1, display alarms.............................................................................................................................................16
Example 2, erase (clear) alarms....................................................................................................................................17
WEEK PROGRAM & DATE PROGRAM ..................................................................................................................................18
Concept description.......................................................................................................................................................18
Week Program, example 1 (New program)....................................................................................................................20
Week Program, example 2 (Change program) ..............................................................................................................21
Week Program, example 3 (Erase program) .................................................................................................................22
Week Program, example 4 (Astronomical function)......................................................................................................23
Week Program, example 5 (Block program)..................................................................................................................24
Week Program, example 6 (Mask program)..................................................................................................................25
Date Program, example (New program) .......................................................................................................................26
DISPLAY PROGRAM.............................................................................................................................................................27
TEMPORARY PROGRAM, EXAMPLE......................................................................................................................................28
GROUP => PERIOD ..............................................................................................................................................................29
DISPLAY HOLIDAYS ............................................................................................................................................................30
SPEC.-FUNCTIONS ...............................................................................................................................................................31
Status..............................................................................................................................................................................32
Status sync. source ........................................................................................................................................................................33
Status impulse output....................................................................................................................................................................33
Status RS232/RS485-port .............................................................................................................................................................33
Status Alarm relay.........................................................................................................................................................................34
Status IP ........................................................................................................................................................................................34
Keylock ..........................................................................................................................................................................35
Language .......................................................................................................................................................................37
Country ..........................................................................................................................................................................38
Position..........................................................................................................................................................................39
Setup ..............................................................................................................................................................................40
Setup sync. source.........................................................................................................................................................................41

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 3 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Setup impulse output.....................................................................................................................................................................42
Setup RS232/485 port ...................................................................................................................................................................44
Setup Alarm Relay........................................................................................................................................................................49
Setup IP.........................................................................................................................................................................................50
Software version ............................................................................................................................................................51
Holidays.........................................................................................................................................................................52
Fixed holidays...............................................................................................................................................................................52
Variable holidays ..........................................................................................................................................................................53
Enable/disable...............................................................................................................................................................................53
Holidays, example 1, insert a new fixed holiday...........................................................................................................................54
Holidays, example 2, erase fixed holiday......................................................................................................................................55
Holidays, example 3, disable a variable holiday ...........................................................................................................................56
Display format ..............................................................................................................................................................................57
PROGRAMMING FORM.........................................................................................................................................58
MAP.........................................................................................................................................................................59
FAULT TRACING....................................................................................................................................................60

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 4 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Technical specifications
General
Crystal Frequency: 4,915200 MHz.
Accuracy: 0,1 sec./24 hours (at +20°C).
Microprocessor: HD6412394.
Slave Clock output
Output 1 and 2:
Impulse system: 1/1 minute, 1/2 minute, second, Time Code (TC)
Type of time: L = Local time, N = Normal time, U = UTC
Impulse length: Minute 0.1-9.9 sec.
Second 0.1-1 sec.
Maximum load / output: 2A (The output is equipped with short circuit protection with automatic reset).
Total load all outputs: 2A.
Impulse memory: 72 hours (impulse memory with rapid impulsing after power failure).General
Relay outputs
Program memory: >100 years (EE-memory).
Number of control functions: 800.
Relay outputs: 4 changeover and 4 closing potential-free contacts.
Max. load/relay output: 230 V 6A.
Total load relay outputs: Number of relay outputs x 6A
Power supply
Connection voltage: 90 - 264V 50 Hz alt. 24 V DC -5% +20 %.
Max ripple (24V DC): 0,7V RMS.
Power consumption: 65 W (max)
Environmental
Ambient temperature: Between 0°C and +40°C.
Relative humidity: Max. 85% non-condensing.
Case: IP 65, light grey plastic (Polystyrol) with transparent protection cover.
CE-Approval, EMC Emission acc. to EN61000-6-3, Immunity acc. to. EN61000-6-2.
Art. numbers: WDP M+S 123362-00 (230V AC)
123360-00 (24V DC)

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 5 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
General description
The Master Clock Programmer is a combination of yearly programmer with 8 outputs for control and regulation
of various energy consumers such as electrical striking plates, buzzers for pause signalling etc,
and a quartz Master Clock with two outputs for operating Slave Clocks.
In case of power failure the built in Real Time Clock keeps the internal time updated. (the outputs are set to
position OFF). Connected Slave Clocks are automatically corrected by rapid impulsing when power returns and
the outputs resume their positions
(ON/OFF) which were previously programmed (with a 10 second switching delay between the different outputs.
Entered data’s are stored for at least 100 years.
The Master Clock Programmer have pre-programmed fixed public holidays and summer/winter time
correction (daylight saving). The clock offers full flexibility with regard to programming working days between
holidays, public holidays to weekdays, holiday periods etc.
A total of 800 control functions can be programmed over 8 outputs. Repeating daily functions on a certain
output only requires 1 control function. Further relay outputs (up to 64) possible by adding one or more
Expansion Units, which are connected to the minute impulse line and to current connection voltage.
Indication for alarm
Indication for mains voltage
Indication for radio synchronisation
Indication for outgoing impulse, output 1
Indication for outgoing impulse, output 2
LED-indication for relay ON
Automatic position (A)
Manual OFF (0)
Manual ON (1)
Connection space

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 6 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Installation
The Master Clock Programmer is intended for wall mounting.
1. Screw in the upper fixing screw halfway and hang up the unit.
2. Screw in the two lower screws, accessible under the connection space cover.
3. Connect the slave clock lines.
4. Connect the signal line/lines (to relay contacts).
1. NOTE! For connection of signals etc., mixed voltages must not be used.
2. Therefore, choose either 230VAC or, for example 24VAC for connection to the relays.
5. Connect, if included, other accessories/options such as radio synchronisation, RS232 etc.
6. Connect the supply voltage.
230VAC
24VDC

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 7 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Calculation of cable area in time systems
General
To make a time system with impulse operated analogue and digital slave clocks perform satisfactory, the cable
from the Master Clock to the Slave Clocks need to be dimensioned correctly.
A 10% voltage drop is allowed in the cable.
The length and area of the cable and also the current (load) on the cable affect the voltage drop.
Formula
A = l x I x k
A = Area [mm2]
l = cable length [m]
I = current [A]
k = 0,015 [constant]
Power consumption
Impulse Slave Clocks
Analogue clocks minute ≤400 mm: 7,5 mA
Analogue clocks minute ≤900 mm: 15 mA
Analogue clocks minute + sweep seconds hand ≤400 mm: 25 mA
Analogue clocks minute 3-wire F/R ≤400 mm: 10 mA
Digital Clocks: 4 mA
Time-Code (TC) Slave Clocks
Analogue clocks minute ≤400 mm: 14 mA (version with movement 113160-00)
Analogue clocks minute ≤400 mm: 7 mA (version with movement 21634-00)
Analogue clocks minute ≤900 mm: 20 mA
Analogue clocks minute + sweep seconds hand ≤400 mm, indoor: 12 mA
Analogue clocks minute + sweep seconds hand ≤400 mm, outdoor: 20 mA
Analogue clocks minute + sweep seconds hand ≤900 mm: 27 mA
Example
A time system consists of 40 pcs. analogue clocks with diameter 300 mm.
The power consumption will then be 40 x 7,5 = 300 mA = 0,3A.
Cable length is 100 metres.
A = 100 x 0,3 x 0,015 = 0,45 mm2
Choose a cable with an area of at least 0,45 mm2.

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 8 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Connection of hourly correction (SR2/3) clocks
The impulse output can be configured to send out hourly correction pulses according to the SR2/3 standard.
See Special functions /Setup /impulse output for more details.
The following hourly correction standards are supported:
SR2-58 : (SR2, hourly correction 2-wired, with imp. correction on the 58th minute).
SR2-59 : (SR2, hourly correction 2-wired, with imp. correction on the 59th minute).
SR3-58 : (SR3, hourly correction 3-wired, with imp. correction on the 58th minute).
SR3-59 : (SR3, hourly correction 3-wired, with imp. correction on the 59th minute).
Connection of 2-wired clocks:
Master Clock Slave Clock
19 --------------------------------- PC
20 --------------------------------- AB
Connection of 3-wired clocks:
Master Clock Slave Clock
19 --------------------------------- A
20 --------------------------------- B
24 --------------------------------- C

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 9 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Synchronisation input
General
The Master Clock is equipped with a synchronisation input intended for connection to an external
synchronisation source. The sync. source can be either a radio receiver type GPS, RDS, MSF, DCF77 or another
Master Clock that transmits synchronisation pulses. The Master Clock is factory prepared for connection to a
radio receiver. Detailed connection diagram for different radio receivers can be found in the separate manual
delivered together with respectively receiver. If the Master Clock is going to be synchronised from another
Master Clock it has to be reconfigured. See below.
Synchronisation from another Master Clock
1. Turn off power.
2. Open the Master Clock by loosening the four screws holding the front panel. Lift the panel and set the
jumpers B4-B6 according to the instruction below.
3. Remount the front panel and turn on the power again.
4. Set the sync. source parameter by using the special function SETUP/SYNC.SOURCE .
5. Connect the sync. pulses to screw terminal 25 and 26.
6. Set the master clock to correct time +/- 30 sec.
7. When the synchronisation pulses have been accepted by the master clock the colon (:) between hours and
minutes in the display starts to flash.
X = Closed
FACTORY DEFAULT
B6
X
B4
X
B5
X
PREPARED FOR SYNC. PULSE FROM ANOTHER MASTER CLOCK
PREPARED FOR RADIO RECEIVER

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 10 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Serial port RS232/RS485
General
The Master Clock has a serial port for connection to a PC or other similar equipment. The serial port is factory
set to RS232. If RS485 connection is used the Master Clock has to be reconfigured according to the jumper
instruction below.
Please see section SPECIALFUNKTION/SETUP/RS232 for details about protocol, baudrate etc.
Connection via RS232
Example:
Master Clock External equipment DTE (9-polig D-sub) (25-polig D-sub)
GND (29) -------------------------------------------------------- 5 -------------------- 7
TD (30) -------------------------------------------------------- 2 -------------------- 3
RD (31) -------------------------------------------------------- 3 -------------------- 2
1 7
4 8
6 20
7 4
8 5
Connection via RS485
1. Turn off power.
2. Open the Master Clock by loosening the four screws holding the front panel. Lift the panel and set the
jumpers B7-B9 according to the instruction below.
3. Remount the front panel and turn on the power again.
5. Connect the RS485 signal to screw terminal 29, 30 and 31.
B9B8B7
X
X
X
PREPARED FOR RS232
PREPARED FOR RS485
FACTORY DEFAULT

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 11 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
MON 14 MAR 2005
10:11:00
LTw
Programming
General
Using 6 buttons and a 2-row 16-character display carries out all programming.
Programming is self-instructive and to simplify the dialogue Yes/No questions are used.
Running mode
When the Master Clock is in operation it shows date and
time in the display.
This is called running mode in this documentation.
LTs = Local Time summer.
LTw = Local Time winter.
1- Select function ↑↓
2- Enter programming mode YES
3- Move sideways ←→
4- Change/scroll ↑↓
5- Accept YES
6- Cancel / Leave prog. mode ←
SET TIME
MON 14 MAR 2005
10:11:00 LTw
WEEK PROGRAM
ALARMS
DATE PROGRAM
TEMPORARY PROGR.
DISPLAY HOLIDAYS
SPEC.-FUNCTIONS
DISPLAY PROGRAM
SLAVE CLOCK
GROUP ÎPERIOD

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 12 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Start up
When the Master Clock is connected for the first time correct/requested
language has to be entered. Press NO until requested
language occurs in the display e.g. English. Accept with YES.
Press NO until correct country code occurs.
For Germany, select DEU. Accept with YES.
Set, by using the arrows, the right time format i.e. year, month, day and hour
but a few minutes in advance.
Wait for the right time and synchronise using YES.
Now the question: SLAVE CLOCK 1 = 12:00
If the Slave Clocks connected to the first output show 12:00, answer YES, if
not set the time shown by the slave clocks. Accept using YES.
Accept using YES.
Now the question: SLAVE CLOCK 2 = 12:00:00
If the Slave Clocks connected to the second output show 12:00:00, answer
YES, if not set the time shown by the slave clocks. Accept using YES.
Accept using YES.
The Master Clock is now in running mode.
NOTE! If a slave clock runs out by a minute, its cabling must be pole changed and
the slave clock to be corrected manually.
NOTE! If the time of the slave clocks is ahead of correct/present time the Master Clock
Programmer will wait until correct time corresponds with the slave clocks.
STARTING
SET TIME
060313 09:07
MON 13 MAR 2006
09:07:00 LTw
LANGUAGE
ENGLISH?
COUNTRY
DEU ?
SLAVE CLOCK 1
= 12:00 OFF
SLAVE CLOCK
= 12:00 ON?
SLAVE CLOCK 1
= 12:00:00 OFF
SLAVE CLOCK
= 12:00:00 ON?

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 13 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Set time when in operation
Select function using ↓.
Enter the programming mode with YES.
Set, by using the arrows, the right time.
Format; year, month, day and hour but a few minutes in advance.
Wait for the right time and synchronise using YES.
Leave programming mode by pressing ←several times.
The master clock is now back in running mode.
Summer to winter ( Day light saving )
Resetting between summer and wintertime is fully automatic and does not need programming.
MON 14 MAR 2005
09:07:00 LT
SET TIME
050613 09:07:00
SET TIME
SET TIME
MON 14 MAR 2005
09:07:00 LT

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 14 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Slave Clock
This function is used to enter the time that the slave clocks are showing.
This is useful if, by some reason, the master clock and the slave clocks should show different times.
When the slave clock time has been entered, the master clock will automatically adjust the slave clocks to
correct time.
Please note that before using this function make sure that all connected slave clocks are showing the same time.
If any of the slave clocks are showing a divergent time this clock must be manually adjusted to the same time as
the other clocks.
The impulses to the slave clocks are temporarily stopped when entering this function.
Select function using ↓.
Enter the programming mode with YES.
SLAVE CLOCK = 09.07? (Example)
If the slave clocks connected to the first output shows 09.07 answer YES,
if not, set the time shown by the slave clocks.
YES.
YES.
SLAVE CLOCK = 09:07:00? (Example)
If the slave clocks connected to the second output shows 09:07:00 answer
YES, if not, set the time shown by the slave clocks.
YES.
YES.
YES.
Leave programming mode by pressing ←several times.
The master clock is now back in running mode.
MON 13 MAR 2006
09:07:00 LTw
SLAVE CLOCK 1
= 09:07 OFF
SLAVE CLOCK
SLAVE CLOCK
MON 13 MAR 2006
09:07:00 LTw
SLAVE CLOCK 1
= 09:07 OFF
SLAVE CLOCK 1
= 09:07 ON?
SLAVE CLOCK 2
= 09:07:00 OFF
SLAVE CLOCK 2
= 09:07: 00 OFF
SLAVE CLOCK 2
= 09:07:00 ON?
SLAVE CLOCK 2
= 09:07:00 ON?

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 15 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Alarms
The master clock is equipped with several supervision facilities to detect functional disturbances.
When a functional disturbance is detected the following will happen:
•Red alarm LED is lit.
•Alarm relay* is activated.
•An alarm message is displayed in function ALARM.
The function ALARM is used to display and erase (clear) alarm messages.
Type of alarm Indication Reason for alarm Action
NO RADIO Red alarm LED lit.
Alarm relay activated.
The radio receiver is
not working.
Check the radio receiver.
If OK, clear the alarm.
UF LOW Red alarm LED lit.
Alarm relay activated
Impulse voltage below
alarm limit.
Check the load on the impulse
output. If OK, clear the alarm.
SHORT CIRCUIT Red alarm LED lit.
Alarm relay activated
Short circuit on
impulse output
Remove the short circuit.
If OK, clear the alarm.
CURRENT LOW Red alarm LED lit.
Alarm relay activated
Impulse current below
alarm limit.
Check the load on the impulse
output. If OK, check that the alarm
limit is correctly configured.
If OK, clear the alarm.
CURRENT HIGH Red alarm LED lit.
Alarm relay activated
Impulse current above
alarm limit.
Check the load on the impulse
output. If OK, check that the alarm
limit is correctly configured.
If OK, clear the alarm.
POWER DOWN Red alarm LED lit.
Alarm relay activated
Works only if the master
clock is equipped with
batteries for running
reserve.
By some reason the
power to the master
clock has been
switched off.
Check the mains.
If OK, clear the alarm.
* One of the relay output can be used as an alarm relay. This function is as default disabled but can be enabled
via SPECIAL FUNCTION/ SETUP/ ALARM RELAY/YES.

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 16 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
To show the alarms
To erase the alarms
Example 1, display alarms
Select function using ↑↓ .
Accept with YES.
Press NO until the wished function is shown.
Accept with YES.
The alarm is displayed.
Press ↑↓ to see next alarm.
Return to running mode press ←.
←.
←.
MON 14 MAR 2005
09:07:00 LT
ALARMS
09MAR 15:52
N
O RADIO
MON 14 MAR 2005
09:07:00 LT
ALARMS- DISPLAY
ALARMS- DISPLAY
ALARMS- ERASE
ALARMS- DISPLAY
ALARMS

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 17 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Example 2, erase (clear) alarms
Select function using ↑↓ .
Accept with YES.
Press NO until the wished function is shown.
Accept with YES.
The alarm is displayed.
Press YES to erase the alarm.
Accept with YES.
Return to running mode press ←.
←.
MON 14 MAR 2005
09:07:00 LT
ALARMS
09JUN 15:52
N
O RADIO
MON 14 MAR 2005
09:07:00 LT
ALARMS- ERASE
ALARMS- ERASE
ALARMS
ERASE?

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 18 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Week Program & Date Program
Using these two functions, programming of the outputs is made.
Concept description
Program A"program" refers to programming an output to a certain time. The word program
represents a single time event and several programs are defined as a group of
programs.
For example: output 2 switches on every working day (Monday-Friday) at 8.00.
Week program A week program is a program, which is repeated every week. You can for each
program choose for which days of the week it shall be valid:
Individual or block programming.
M = Monday
T = Tuesday
W = Wednesday
T = Thursday
F = Friday
S = Saturday
S = Sunday
Date program A date program is a program, which is valid for a specific date.
Group A group of programs, signal events.
Type of signals There are some different kinds of signals, depending on how the relay output is to
be used.
ON/OFF Is used when a longer lasting switching ON is required, e.g. for controlling fans,
door locks, lighting etc.
01s Is used when a short pulse is required, e.g. for bells/buzzers.
Pulse duration selectable from 1-99 seconds.
Astr. Astr. (Twilight) is a function which closes/opens a predestined relay at sunrise
resp. sunset. Which day and month of the year it is, and where the Master Clock is
located geographically, define the time of the sunrise resp. sunset.
The sunrise resp. sunset are calculated in the software of the Y8 module.
The geographic position of the Master Clock is entered at starting up.
A map indicating latitude (Enorth) and longitude (Eeast) is enclosed.
Mask A program that is repeated f. ex every hour is easily entered by the use of mask
program.
XX.15.00 ; the program is repeated every hour att minute 15.
08.XX.00 ; the program is repeated every minute between 08.00 and 09.00.
XX.XX.00 ; The program is repeated every minute.

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 19 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
To simplify programming 3 sub menus are used:
To enter new programs.
To erase a separate existing program.
To change existing programs.
WEEK PROGRAM
NEW GROUP A
WEEK PROGRAM
ERASE GROUP A
WEEK PROGRAM
CHANGE GROUP A

Document: 1784en02.doc
QWTIME III MASTER CLOCK Author: PM
Date: 2008-11-07
User Manual Page: 20 of 61
WESTERSTRAND URFABRIK AB
P.O. Box 133 Tel. [phone] Internet:: http://www.westerstrand.se
SE-545 23 TÖREBODA Fax. [phone] E-mail: [email protected]
Week Program, example 1 (New program)
Example: Outputs No. 2 shall switch on Monday – Friday at 09.00 and off at 17.00.
Select function using ↑↓.
Enter programming mode using YES.
Select new program using YES.
Select group of programs using ↑↓, accept using YES.
Select output using ↑↓. Move to the right using →.
State type of signal using ↑↓.
State the days the program shall function using ↑↓.
Move to the right using →.
State the time of the program using ↑↓.
Move to the right using →.
Accept using YES.
If the program is approved the text “Program saved” is displayed quickly.
Continue with programming OFF for the same output or leave
programming by pressing ←several times.
MON 14 MAR 2005
09:07:00 LT
WEEK PROGRAM
WEEK PROGRAM
NEW GROUP A
OUTPUT 2 ON
------- 08:00:00
OUTPUT 2 ON
MTWTF-- 08:00:00
WEEK PROGRAM
NEW GROUP A
OUTPUT 2 O
N
------- 08:00:00
OUTPUT 2 ON
MTWTF-- 09:00:00
OUTPUT 2 OFF
MTWTF-- 17:00:00
WEEK PROGRAM
MON 14 MAR 2005
09:07:00 LT