Westinghouse MT25 ARM9 Guide

ISSUED: 04-16-04 SHEET #: 095-9194-11 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Installation and Assembly -
Swivel Wall Arm for LCD screens Model: MT25 ARM9
PART # QTY. DESCRIPTION
A095-0149 1 LCD screen swing arm
B590-1110 1 cord wrap
C590-5003 4 retaining spacer
D500-2011 2 #14 X 2" wood screw
E590-0097 2 concrete anchor
F504-2013 4 M4 x .7 x 12 mm philips head screw
G520-2027 4 M4 x .7 x 10 mm philips head screw
H504-2014 4 M4 x .7 x 20 mm philips head screw
Parts List
E
D
IMPORTANT! Read entire instruction sheet
before you start installation and assembly.
A
B
Max. Load 25 lb (11.34 kg)
C
FGH

ISSUED: 04-16-04 SHEET #: 095-9194-12 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
For Wood Stud Walls: Use a stud finder to locate
center of stud. Drill two 3/16" (5 mm) dia. holes to a
minimum depth of 2" (51 mm). Attach swing arm to
center of wood stud using two screws (D).
IMPORTANT: Make sure wall bracket is level on wall.
Removeknobfromtilt/adapterplate.
KNOB
TILT/ADAPTER
PLATE
• Tighten wood screws so that wall plate is firmly
attached,butdonotovertighten.Overtighteningcan
damagethescrews, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finderishighlyrecommended.
WARNING
D
WOOD
STUD
WALL
WALL
BRACKET

ISSUED: 04-16-04 SHEET #: 095-9194-13 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
For Concrete Walls drill one 1/4" (6 mm) dia. hole to a
minimumdepth of 2"(51 mm). Insertanchor (E) in hole
flush with wall as shown (right). Place wall bracket, with
slotontubefacingdown,overanchor(E)andsecure
with #14 x 2" wood screw (D). Make sure wall bracket is
level,markotherholeandrepeatstepswithother
fasteners.Tightenallfasteners.
IMPORTANT: Make sure wall bracket is level on wall.
concrete
wall
1
3
2
E
E
wall bracket
D
E
WALL
BRACKET
CUTAWAYVIEW
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
toavoid breaking out the backof the hole when enteringa void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hard-
wareandcomponents.
D
Drill hole and insert anchor (E)
Place wall bracket over anchor (E) and secure with
screw (D)
After repeating step one tighten all fasteners
• Tighten concrete anchor bolts firmly, but do not
overtighten.Overtightening can damage the bolts,
greatlyreducingtheir holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concreteanchorsare not intended for attachment to
concretewallcovered with a layer ofplaster, drywall,
orotherfinishing material. If mountingtoconcrete wall
coveredwithplaster/drywall is unavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer.
WARNING

ISSUED: 04-16-04 SHEET #: 095-9194-14 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
This product is designed to accommodate screens with Vesa®compliant hole
pattern. For safe mounting, please make sure that mounting screws turns at least
three complete turns in the screen inserts.
FORVESA75MOUNTINGPATTERN:1.
Choosehole pattern indicated below. 2.Attach
tilt/adapter plate to back of monitor using four
10 mm screws (G) as indicated below. 3. If
hole pattern is in a pocket, attach tilt/adapter
plate to back of monitor using four 20 mm
screws(H) and fourretainingspacers(C)as
indicatedbelow.
Note: Screen may appear slightly
different than illustrated
For screens with a hole
pattern in a pocket,
spacers (C) go between
tilt/adapter plate and
monitor.
FORVESA100MOUNTINGPATTERN:1.
Choosehole pattern indicated below. 2.Attach
tilt/adapter plate to back of monitor using four 10
mm screws (G) as indicated below. Note: If you
don't get three complete turns in the screen
inserts, use four M4 x 12 mm screws (F) instead
of four M4 x 10 mm screws (G).
Note: Screen may appear slightly
different than illustrated
G or H
G or F
TILT/ADAPTER
PLATE
TILT/ADAPTER
PLATE

ISSUED: 04-16-04 SHEET #: 095-9194-15 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
POWER
CORD
CORD
WRAP
CUTAWAY
OFTUBE
FlipLCDupward.Wrappowerand A/V cords
withcordwrap.Feedcordwrap throughholeon
bottom of wall bracket into tube to avoid pinch-
ing wires between wall bracket and tube. Next
routethroughandbetweenpivotbracketandtilt/
adapterplate.
TILT/ADAPTER
PLATE PIVOT
BRACKET
Adjust tilt and secure pivot bracket to tilt/adapter plate with knob.
KNOB
LCDSCREEN

ISSUED: 04-16-04 SHEET #: 095-9194-16 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”)thattheProduct will be free from defectsinmaterial and workmanship, under normal use, foraperiod of five (5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital
Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
daysfrom the date of delivery to the end-user, whichever occurslast.
OBTAINING WARRANTY SERVICE –Toobtainwarrantyservices,you must either personally deliverorship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at [phone] to
obtainaReturnMerchandiseAuthorization (“RMA”) and for other instructions regarding return and replacement orrepairof
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO WARRANTY –Thiswarranty does not cover damage causedby(a) service or repairs by anyone other
thanpersonnelauthorized by Westinghouse Digital Electronics, (b)the failure to utilize proper packingwhenreturning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transitor otherwise.
PROOF OR ORIGINAL PURCHASE –Asales receipt, invoice, or other proof of purchase specifying the original date of
purchasewithin the five (5) year warranty period must be presented to obtain warrantyservice. This warranty extendsto
theoriginal purchaser and is not transferable.
EITHER REPAIR OR REPLACEMENTIS YOUR EXCLUSIVE REMEDYUNDER THIS WARRANTY. EXCEPT TO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIALDAMAGESCLAIMEDTOARISE FROM BREACHOFANYEXPRESS OR IMPLIED WARRANTYON
THISPRODUCT. ANYIMPLIED WARRANTYOF MERCHANTABILITYOR FITNESS FORAPARTICULARPURPOSE
ONTHIS PRODUCTIS LIMITED IN DURATIONAND SCOPETOTHETERMS OFTHISWARRANTY.
Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how
longan implied warranty lasts,so the above limitation may not applyto you. This warranty givesspecific legal rights, and
you may also have other rights which vary from State to State.
WestinghouseDigital Electronics, LLC
16257East GaleAve.
City of Industry, California 91745
Tel: [phone].
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.