Westinghouse MT80 THIN Guide

R
Max Load Capacity: 80 lb (36.3 kg)
ISSUED: 03-02-05 SHEET #: 201-9323-1
Installation and Assembly:
Universal Flat Wall Mount for 22" - 37" Screens
Model: MT80 THIN
Features:
•Universaldesignfor22"to37"plasmaandLCDscreens
•Low-profile design keeps the screen close up against the wall
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.

2 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•phillips screwdriver
•drill with 1/4" and 5/32" drill bits
• DonotbegintoinstallyourWestinghouseproductuntilyouhaveread and understood the instructions and warnings
containedinthis Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
callPeerless customer serviceat 1-800-729-0307.
• Makesure that the wall will safely support the combined load of the equipment and all attached hardware and compo-
nents.
• Neverexceed the Maximum Load Capacity of 90 lb (40.8 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edgeto edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tightenscrews firmly, but donotovertighten. Overtightening can damage theitems, greatly reducing their holding
power.
WARNING
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Single Wood Stud Wall...................................................................................................................................4
Installation to Double Wood Stud Wall..................................................................................................................................5
Installation to Solid Concrete or Cinder Block .......................................................................................................................6
Installing Flat Panel Screen to Wall Plate.............................................................................................................................7
AddingSafety to Mount ........................................................................................................................................................7
For customer service call [phone] or [phone].

3 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
AA
CC
FF
BB
EE
DD
MT80 THIN
Description Qty Part #
AA wall plate 1 200-4629
BB adapter bracket 2 200-4628
CC #14 x 2.5" wood screw 4 5S1-015-C04
DD M5 x .8 x 25 mm socket head cap screw 2 520-9567
EE Alligator® anchor 4 590-0097
FF 4 mm security allen wrench 1 560-1145
Parts List
Before you begin, make sure all parts shown are included with your product.

4 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Installation to Single Wood Stud Wall
1Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center
of studs with pencil. Drill three 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.Attach wall plate (AA) using three #14
x 2.5" wood screws (CC).
Skip to step 2 on page 7.
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and
hardware.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
CC
AA

5 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Installation to Double Wood Stud Wall
1Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center
of studs with pencil. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep.Attach wall plate (AA) using four #14 x
2.5" wood screws (CC).
Skip to step 2 on page 7.
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and
hardware.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
WARNING
CC
AA

6 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Installation to Solid Concrete or Cinder Block
1Use wall plate (AA), making sure that it is level, as
a template to mark holes. Drill four 1/4" (6 mm) dia.
holes to a minimum depth of 2-1/2" (64 mm). Insert
anchors (EE) in holes flush with wall as shown
(right). Place wall plate over anchors and secure
with #14 x 2.5" screws (CC). Tighten all fasteners.
• When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con-
crete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a
solid part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoidbreaking out the back ofthehole when entering a voidorcavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
WARNING
CUTAWAY VIEW
INCORRECT
concrete
surface
1
3
2
EE
Drill holes and insert anchors (EE).
CORRECT
Place plate (AA)over anchors (EE) and secure with
screws (CC).
Tighten all fasteners.
wall
plate
plaster/
drywall
concrete wall plate concrete
plaster/
drywall
• Always attach concrete expansion anchors directly to
load-bearingconcrete.
• Never attach concrete expansion anchors to con-
crete covered with plaster, drywall, or other finishing
material. If mounting to concrete surfaces covered
with a finishing surface is unavoidable, the finishing
surface must be counterbored as shown below. If
plaster/drywall is thicker than 5/8", custom fasteners
must be supplied by installer.
WARNING
AA
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
WARNING
CC
AA
EE
CC
EE
solid concrete cinder block

7 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Installing Flat Panel Screen to Wall Plate
3
Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in
place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make
sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired.
Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten
screws with 4 mm security allen wrench (FF).
2
Adding Safety to Mount
BB
AA
BB
Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen.
DD AA
BB
DETAIL 1
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the plasma television.
WARNING
detail 1

8 of 8 ISSUED: 03-02-05 SHEET #: 201-9323-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”)that the Product willbefree from defects inmaterialand workmanship, under normaluse,for a period of five(5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital
Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
daysfrom the date of delivery to the end-user, whichever occurs last.
OBTAINING WARRANTY SERVICE –Toobtainwarranty services, you must either personallydeliveror ship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at [phone] to
obtainaReturn MerchandiseAuthorization (“RMA”)and forotherinstructions regardingreturn and replacementor repair of
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO WARRANTY – Thiswarranty does not coverdamagecaused by (a) serviceorrepairs by anyoneother
thanpersonnel authorized by Westinghouse DigitalElectronics,(b) the failure to utilizeproperpacking when returning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transitorotherwise.
PROOF OR ORIGINAL PURCHASE –Asales receipt, invoice, or other proof of purchase specifying the original date of
purchasewithinthefive(5)year warranty period must be presented to obtain warranty service. This warranty extends to
theoriginalpurchaserandis not transferable.
EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDYUNDERTHIS WARRANTY. EXCEPTTO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIALDAMAGESCLAIMEDTOARISEFROM BREACHOFANYEXPRESSOR IMPLIED WARRANTYON
THISPRODUCT. ANYIMPLIED WARRANTY OF MERCHANTABILITYOR FITNESS FORAPARTICULARPURPOSE
ONTHISPRODUCTIS LIMITED IN DURATIONAND SCOPETOTHETERMSOFTHIS WARRANTY.
Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how
longanimplied warranty lasts, so the above limitation may not apply to you. This warranty gives specificlegalrights,and
you may also have other rights which vary from State to State.
WestinghouseDigital Electronics, LLC
16257EastGaleAve.
Cityof Industry, California 91745
Tel:[phone].
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.

1 of 4 ISSUED:01-18-05 SHEET#:201-9325-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Description Qty. Part #
AM4 x .7 x 12 mm phillips screw 6 504-9013
CM4 x .7 x 25 mm phillips screw 6 504-1015
EM5 x 40 mm pan head phillips scew 4 520-1199
FM6 x 25 mm pan head phillips screw 4 520-1208
GM6 x 1 x 20 mm pan head phillips screw 4 520-9402
HM5 x .8 x 12 mm pan head phillps screw 4 520-1027
IM6 x 1 x 12 mm pan head phillips screw 6 520-1128
KM5 x 25 mm pan head phillips screw 6 520-9543
Omulti-washer 6 580-1036
S.25" ID x .5" OD x .625" H nylon spacer 4 590-1106
V.251" ID x .5" OD x 1.25" H aluminum spacer 4 580-1067
Parts List
Model: MT80 THIN
Installing Adapter Brackets to
the Flat Panel Screen
Begin with product installation and assembly manual before reading this instruction manual.
BB
Note:Thispartislistedonthe
productinstallationandassem-
blymanual.
OI
FA C H
S VK
E G

2 of 4 ISSUED:01-18-05 SHEET#:201-9325-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Continued on the following page...
To assemble the adapter brackets to your screen, begin with the table on pages 2 and 3. Find the configuration
that corresponds to your screen. Refer to the configuration table on page 3 to install the adapter brackets.
Notes: TheUniversalFlatWallMountisa universal mount which accommodates a wide variety of screens. If your particular
screen is not listed on pages 2 and 3 or unsure which configuration matches your screen, please contact customer service
to ensure product compatibility.
Screen
Size
Akai 22" LC2260 K
BenQ 30" DV3070
(
DV3080
)
A
CTX 23" H2300 K
Dell 23" W2300 K
Dell 26" W2600
A
Dell 30" W3000
A
Gateway 23" GTW-L23M102 K
Gateway 26" GTW-L26M103
A
Gateway 30" GTW-L30M103
A
Hewlett Packard 23" f2304 K
IBM 22.2" T221 K
Image Systems 24" FP2400MAX K
JVC 23" LT23X475 K
JVC 26" LT26WX84, LT26X575 F
JVC 32" LT32WX84, LT32X575 F
LG 22" 285LT, 295LM K
LG 23" RU-23LZ21, RU-23LZ50C, L2320A, L2323T K
LG 27" RU-27LZ50C
A
LG 30" L3000A F
LG 30" L3020T, RU-30LZ50C
A
LG 30" DU-30LZ30
A
LG 32" RU-32LZ50C
A
Maxx Products 30" MAXX 3000 I
Luce 22" LCTV2201A / GB K
MAXENT 27" MX-27X1
A
MAXENT 30" MX-30X1
A
Mitsubishi 22" LT-2220, LT-2240 K
Mitsubishi 30" LT-3020, LT-3040, LT-3050
A
Mitsubishi 30" MLM300
A
NEC-Mitsubishi 30" LCD3000
A
Net T
V
30" LCTV-30W I
Ovideon 27" LC2700w
A
Ovideon 30" LC3000W
A
Panasonic 22" TC-22LH1 K
Panasonic 26" TC-26LX20 C
Panasonic 32" TC-32LX20 C
Panasonic 32" TC32LH1 C
Philips 23" 23FW995/997, 23PF9945 K
Philips 23" 23PF8946, 23PF8946A K
Philips 23" 23PF9966 K
Philips 26" 26PF9966
A
Philips 30" 30PF9975, 30FW9955, 30FW9975, 30FW995, 30FW997 F
PixelPro 27" PX-27XP10
A
PixelPro 30" PX-30XP10
A
Planar 22" XP22WSA-01 K
Planar 23.1" WS231 K
Samsung 22" LTM225W, LTN226W K
Samsung 24" S
y
ncmaster 204T, 240T, 243T K
Samsung 26" LT-P266W
A
Sceptre 23" Na
g
a X23S K
Sceptre 30" X30SV- Naga III A
Sharp 26" LC-26GA4U, LC-26GD4U, LC-26GD6U
A
Sharp 30" LC-30HV2U, LC-30HV4U, LC-30HV6U
A
Sharp 32" LC-32G4U, LC-32GD4U, LC-32GD6U L
Sharp 37" LC-37HV4U, LC-M3700, LC-37HV6U, LC-37G4U, LC-37GD4U, LC-37GD6U L
Sony 23" LMD-230WS K
Sony 23" KLV-23HR2, SDM-232W/B K
Sony 23" KLV-23M1 K
Sony 26" KLV-26HG2
A
Sony 30" KLV-30XBR900, KLV-30XBR950, LDM3000 F
LCD Screens
Config.Manufacturer Manufacturer Model

3 of 4 ISSUED:01-18-05 SHEET#:201-9325-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Usingyourscreen'sconfiguration letter from the
previoustable, find the configuration that
corresponds to your screen. Refer to the table
below to find which fasteners to use when installing
theadapterbracketsandusethecorresponding
hole in the multi-washer (O) that matches your
screw size as shown in figure 1.
**Note: Ifscrews (A)do not engagewithfour complete
turns, then use screws (C) with spacer (S).
**Note: If screws (I) do not engage with the threads
inside the mounting hole then use screws (G).
If screws (G) are not long enough then use
screws (F).
TOP
BOTTOM
TOPHOLEFORM5SCREWS
MIDDLEHOLEFORM4SCREWS
BOTTOMHOLEFORM6SCREWS
fig. 1
O
1
Config. Screws Spacer
AAno
BIno
CCS
FHno
GKS
HEV
IFS
*K Ano
**L Ino
Screen
Size Config.Manufacturer Manufacturer Model
Sony 32" KDL-32XBR950 G
Sony 32" KLV-32M1
A
Studio Experience 30" SELCD300 I
Syntax 27" LT27HV
A
Syntax 30" LT30HV
A
Tatung 23" V23CLT
T
K
Tatung 27" V27CMT
T
A
Tatung 30" V30CMT
T
A
Toshiba 26" 26HL83
A
Toshiba 26" 26HL84
A
Toshiba 32" 32HL84
A
ToteVision 22" LCD-2200VT, LCD-2216TD K
ViewSonic 22.2" VP2290b K
ViewSonic 23" VP230mb K
Viewsonic 27" N2700w I
Viewsonic 30" N3000w C
Viewsonic 30" N3020w C
Westinghouse 27" LTV-27w2
A
Westinghouse 27" W32701
A
Westinghouse 30" LTV-30w2 C
Westinghouse 30" W33000, W33001
A
Westinghouse 32" LTV-32w1
A
Westinghouse 37" LTV-37w2 HD
A
Westinghouse 37" LVM-37w1
A
Zenith 23" L23W36 K
Zenith 27" L27W46
A
Eiki 32" PLD-32U G
Hitachi 32" 32HDT20, 32HDT50, 32HDT55, 32HDT60 B
Hitachi 37” CMP307SX, CMP307U, CMP307XU B
Maxx Products 32" MAXX 3200 I
Monovision 32" PD3231 I
Philips 32" 32FD9954, 32FW997 F
Philips 37" 37FD9944, 37FD9954/17, 37PF9965 F
Sanyo 32" PDP-32H1A G
Sony 32" KZ-32TS1U, KZ-32TS1, KE-32TS2 H
Studio Experience 32" SEPD3200, SEPD3231 I
Plasma Screens

4 of 4 ISSUED:01-18-05 SHEET#:201-9325-1
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
SCREWS
SPACERS
BB
fig 2.2
BB
O
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2.1.
Refer to step 1 to determine the proper fasteners to use. Attach the adapter brackets to the back of the screen using
the appropriate combination of screws, multi-washers (O), and spacers as shown in figure 2.2. Verify that all holes are
properlyaligned, and then tightenscrewsusing a phillips screwdriver.
2
BB
CENTERBRACKETSVERTICALLY
ONBACKOFSCREEN
X
X
fig 2.1
BB
Note: "X"dimensions should be equal.
Notes:
• Thenumber of fastenersused will vary,
dependingupon the type ofscreen.
• Spacersmay not be used,dependingupon
the type of screen.
• Tightenscrews so adapter brackets are firmly
attached. Do not tighten with excessive force.
Overtighteningcan cause stress damageto
screws,greatly reducing their holdingpower and
possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.)
maximumtorque.
WARNING
Installing Adapter Brackets
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.