Wetronic MS16 User manual

Important:
Before you can use this switch,
you have to use the signal setup menu first!
2014
Manual MS16

Page 2
2
Preface
Thank you for purchasing the Wetronic MS16 Multiswitch module. With this
manual we will help you with installing the multiswitch in both your
transmitter and model. It’s important for us that this manual is as clear as
possible for you. If you still have any questions please contact us at:
[e-mail]
Technical Specifications:
Encoder:
Dimensions: 55x30mm
Voltage: 5V DC
Power Consumption: <30mA
Decoder:
Dimensions: 46x27x10mm
Voltage: 5-6V DC
Power Consumption: 20-200mA
Number of outputs: 16
16 outputs: 16x 0,2A / 8x 0,2A + 8x 2A / 16x 2A

Page 3
3
Index
Preface .............................................................................................................. 2
Technical Specifications: ................................................................................... 2
Overview encoder:............................................................................................ 4
Overview decoder:............................................................................................ 5
Installation in the transmitter:.......................................................................... 6
Installation in the model................................................................................... 7
Signal Setup for the first use............................................................................. 8
Signal setup for the MS16:........................................................................ 8
Memory / Puls setup......................................................................................... 9
Memory / Puls Setup ................................................................................ 9
Examples of connecting .................................................................................. 10
Connecting LEDS to the outputs ............................................................. 10
Connecting an small DC motor ............................................................... 10

Page 4
4
Overview encoder:
Description
Explanation
A
Signal cable
3 core cable
B
Signal connector
Multi out connector
C
Channel cable
Servo 1 core cable
D
Switches 8x
8x Switch (on)-off-(on)

Page 5
5
Overview decoder:
Description
Explanation
1-16
16 outputs
Green LED
ERR
Error led
Red LED
Sign. Setup
Signal Setup
Mem. Setup
Memory Setup
Ont.
Receiver
Servo cable to receiver
•
Ground
Ground wire for the outputs

Page 6
6
Installation in the transmitter:
1. Open the transmitter.
2. Mount the encoder with the 8 nuts tot he transmitter case.

Page 7
7
3. Connect the encoder in the transmitter
- White connector on the multi out.
- Black servo connector on the channel 6,7 or 8 (free to choose)
(The channel chosen in the transmitter is the channel used on the
receiver later on)
Installation in the model.
Indien alles correct is aangesloten branden er geen leds.
Mocht de rode led toch nog branden controleer of alles juist is aangesloten
en ook op hetzelfde kanaal is aangesloten.

Page 8
8
Signal Setup for the first use
After installation of the module it’s important that the signal setup mode is
done correctly.
Signal setup for the MS16:
1. Place the jumper on the Sign. Setup
2. Turn on the transmitter and keep one switch pressed until the
end of this setup mode.
3. Turn on the receiver.
4. After 5 seconds the red LED will start to blink
5. Release the switch and disconnect the decoder.
6. Remove the jumper on the signal setup and reconnect the
decoder.
7. The signal setup has been programmed for your transmitter.

Page 9
9
Memory / Puls setup
This setup makes it possible to program any output of the ms16.
With memory mode the output will be active until you press the same
channel again. With puls mode the output will be deactivated when you
release the switch.
Memory / Puls Setup
1. Place the jumper on Mem. Setup
2. Turn on the transmitter
3. Turn on the receiver
4. Be sure that the decoder is connected tot he right channel.
5. The red light will light up very short to confirm the mem setup.
6. Any output you activate right now will be an memory output.
7. Any output inactive will be an puls output.
8. After about 20 seconds the mem setup will end automatically and
confirm this with an red blinking led.
9. Disconnect the decoder from the receiver.
10. Remove the jumper from mem setup
11. Reconnect the decoder tot he receiver and confirm your config.

Page 10
10
Examples of connecting
Below we will give some examples for how to connect different items tob e
connected tot he decoder outputs. It’s important to know that this module
like almost any other electronics out there uses N channels to switch on or
off. This means it switches the outputs to ground. This makes it possible to
use multiple voltage on the module outputs with switching.
Connecting LEDS to the outputs
Connecting an small DC motor
*To turn the motor in both ways (lef tand right) you’ll need an extra module:
Motor Reversal Module you can find this in our webshop.