Whalen PROEC41-NV User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Page 1
ADULT ASSEMBLY REQUIRED
LOT NUMBER:
DATE PURCHASED: / /
Panel TV Stand
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to
the store where it was purchased. Please call our customer service number and have
your instructions and parts list ready to provide the model name, part name or factory number.

Page 2
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening Bolts.
7. Make sure all Bolts are tightly fastened before the unit is used.
MAXIMUM RECOMMENDED WEIGHT LOADS
GENERAL INFORMATION
,
TIPS and TRICKS
MAXIMUM LOAD 50 lb. (22.6 kg)
FITS UP TO MOST 47” FLAT PANEL TVs
MAXIMUM LOAD 135 lb. (61.2 kg)
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH
FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND
WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT
PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE
CENTER OF THE UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT
PANEL TVS OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT
LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.
This product is sold with one set of Tipping Restraint Hardware Kit. You must install the Tipping
Restraint Hardware between the wall and the TV stand to prevent any accidents or damages.
When properly installed, this restraint can provide protection against the unexpected tipping of
the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and is not a
substitute for proper adult supervision. Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
CATALOG: Flat Panel TV Stand
MADE IN CHINA

Page 3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware
are present before beginning assembly.
A- Left Side Frame (1) B- Right Side Frame (1) C- Back Panel (1)
D - Back Top Frame (1) E- Back Bottom Stretcher (1) F- Top Crossbar (1)
G- Top Stringer (1) H- Middle Crossbar (1) I- Middle Stringer (1)
J- Bottom Brace (1) K- Bottom Stringer (1) L- Left Front Post (1)
M- Right Front Post (1) N- Top Glass (1) O- Middle Glass Shelf (1)
P- Bottom Glass Shelf (1) Q- Swiveling Bracket (1) R- Mounting Frame (1)
S- Monitor Bracket (2) T- Cable Wheel (2)

Page 4
Parts and Hardware List
(1) Suction Cup (2) 5/8” Bolt (3) 3/4” Bolt (4) 1-1/4” Bolt
(15+1 extra) (10+1 extra) (8+1 extra) (4+1 extra)
(5) 1-5/8” Bolt (6) 2-1/4” Bolt (7) Hex Nut (8) Lock Washer
(12+1 extra) (6+1 extra) (8+1 extra) (40+2 extra)
(9) Flat Washer (44+2 extra) (10) #4 x 10 mm Screw (4+1 extra) (11) Floor Leveler (2)
Touch-up Pen Open Wrench M4 Allen Wrench Tipping Restraint Hardware Kit (1)
(1) (1) (2) (Inside Plastic Bag)
TV Mounting Kit
M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)
M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)
M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)
Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)
Tools required: Allen Wrench, Open Wrench (provided) and Phillips screwdriver (not provided).

Page 5
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,
go back and fully tighten all bolts. This will make the assembly easier.
1. Attach the Back Top Frame (D) and the Back Bottom Stretcher (E) between Left and Right
Side Frames (A and B). Make sure that the metal brackets on Back Bottom Stretcher (E) face
up and point forward. Tighten the bolts with the enclosed M4 Allen Wrench.
D
A/B
A/B E
5
5
Lock Washer
(8 used in this step)
⑧
Flat Washer
(8 used in this step)
⑨
1-5/8” Bolt
(8 used in this step)
⑤

Page 6
Assembly Instructions
2. Pick up the Back Panel (C) and fit it between the front of Left and Right Side Frames (A and B),
as shown above. Insert and screw four 10 mm Screws (10) through the corner brackets to
secure the Back Panel in place. Make sure that the oval holes on the Back Panel are down.
Tighten the screws with a Phillips screwdriver.
#4 x 10 mm Screw
(4 used in this step)
⑩

Page 7
Assembly Instructions
3. Lay down the unit on a level and protective surface, as shown.
4. Screw the Floor Levelers (11) into the front sockets underneath the bottom rail of Left
and Right Side Frames (A and B). Set the Levelers to the correct height.
5. Attach the Bottom Brace (J) to the bottom rail of Left and Right Side Frames (A and B).
Lock Washer
(2 used in this step)
⑧
2-1/4” Bolt
(2 used in this step)
⑥
Flat Washer
(2 used in this step)
⑨
Floor Leveler
(2 used in this step)
⑪

Page 8
Assembly Instructions
6. Attach the Middle Crossbar (H) to the middle rail of Left and Right Side Frames (A and B).
Tighten the bolts with enclosed M4 Allen Wrench.
7. Repeat the last step to attach the Top Crossbar (F) to the top rail of Left and Right Side
Frames (A and B).
Lock Washer
(4 used in this step)
⑧
Flat Washer
(4 used in this step)
⑨
1-5/8” Bolt
(4 used in this step)
⑤

Page 9
Assembly Instructions
8. Align and attach the Stringers (G, I and K) to the end brackets on the front rails of the Side
Frames (A and B) respectively, as shown above. Make sure that the top surface of stringers
and back crossbars are flush with each other.
28
2
8
Lock Washer
(6 used in this step)
⑧
5/8” Bolt
(6 used in this step)
②
Flat Washer
(6 used in this step)
⑨

Page 10
Assembly Instructions
9. Stand the last assembly upright.
10.Align and attach Left and Right Front Posts (L and M) to the Middle Stringer (I) and the Bottom
Stringer (K), as shown above.
Lock Washer
(8 used in this step)
⑧
Flat Washer
(8 used in this step)
⑨
3
98
4
98
3/4” Bolt
(4 used in this step)
③
1-1/4” Bolt
(4 used in this step)
④

Page 11
Assembly Instructions
11.Attach the Swiveling Bracket (Q) to the top of the Back Top Frame (D) with the pivoting bolt
head up, as shown. Securely tighten with the provided Open Wrench and M4 Allen Wrench.
NOTE: The Back Top Frame can provide three height options for your TV set. Refer to your
TV size and adjust the Swiveling Bracket at your desired height for optimum viewing.
UP
QD
8
Lock Washer
(8 used in this step)
⑧
Flat Washer
(8 used in this step)
⑨
2-1/4” Bolt
(4 used in this step)
⑥
Hex Nut
(4 used in this step)
⑦

Page 12
Assembly Instructions
12.Attach the Mounting Frame (R) to the Swiveling Bracket (Q) using four 3/4” Bolts (3) with
Washers (8 and 9) and then secure with the Hex Nuts (7). As shown above.
13.Go back and tighten all bolts with the enclosed Allen Wrench and Open Wrench.
UP
Lock Washer
(4 used in this step)
⑧
Flat Washer
(8 used in this step)
⑨
Hex Nut
(4 used in this step)
⑦
3/4” Bolt
(4 used in this step)
③

Page 13
Mounting Monitor Bracket to a television with a flat back
NOTE: For televisions with a curved or recessed back, proceed directly to the next page.
14.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded inserts on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
15.Follow the appropriate diagram above to attach the Monitor Brackets (S) to the back of your
TV with the selected fasteners. Make sure the Monitor Brackets are centered and level with
each other. Secure the bolts with a Phillips screwdriver. DO NOT over tighten the bolts.
NOTE: Lean the TV up against a wall or other solid surface when attaching with the Monitor
Brackets. DO NOT place the TV face down on the glass, this may cause permanent damage.
TV

Page 14
Mounting Monitor Bracket to a television with a curved / recess back
16.Determine the correct diameter of the bolt your TV requires by hand threading them into the
threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If
you are unable to find the correct bolt consult a local hardware store.
17.Follow the appropriate diagram above to attach the Monitor Brackets (S) to the back of your
TV with the selected fasteners. Make sure the Monitor Brackets are vertically centered and
level with each other. Secure the bolts with a Phillips screwdriver. DO NOT over tighten the
bolts.
NOTE: Lean the TV up against a wall or other solid surface when attaching with the Monitor
Brackets. DO NOT place the TV face down on the glass, this may cause permanent damage.
TV

Page 15
Assembly Instructions
18.Once the Monitor Brackets (S) are attached onto the back of television, ask for assistance to
lift the television up to attach the Monitor Brackets onto the Mounting Frame (R). Set the
hooks of the Monitor Brackets over the Mounting Frame then lower them onto the bars of the
Mounting Frame. Loosen the Safety Bolt pre-attached on the Monitor Brackets to ensure an
easy fit at the bottom hooks. Proceed to center the television.
2

Page 16
Assembly Instructions
19.Attach 2 Cable Wheels (T) to the backside of the assembled unit with the 5/8” Bolts (2).
Tighten the bolts with the enclosed Allen Wrench.
20.The Cable Wheels allow you to organize, route and separate your component cords and
cables to minimize tangling and signal interference.
5/8” Bolt
(4 used in this step)
②

Page 17
Assembly Instructions
21.Put the Suction Cups (1) firmly into the top holes on the Crossbars (F, G and H) and the
Stringers (I, J and K). TIP: If a suction cup resists insertion, try pressing down on the middle of
the cup with the Allen Wrench while twisting it clockwise into the hole.
22.Set the Glass Shelves (N, O & P) in place, with the black side of the glass shelf down, onto
the inserted Suction Cups (1), starting with the Bottom Glass Shelf (P), as shown. Make sure
that the arrow on the center sticker on each glass shelf aligns with the center of the Back
Panel (C) properly. Push each glass all the way back against the post of the Left & Right Side
Frames.
NOTE: If a glass shelf is scratched, you can minimize the damage by using a BLACK marker
and filling in scratched area from underneath.
Suction Cup
(15 used in this step)
①
H
J

Page 18
Assembly Instructions
Tools required: Allen Wrench (provided), Phillips screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.
23.Position the assembled console at the desired location against a wall. If necessary, adjust the
pre-attached Floor Levelers on the bottom of the Side Frames (A and B) to level the console.
24.Now, follow the instructions printed on the plastic bag containing the Tipping Restraint
Hardware to mount the tip-over restraint to the Back Top Frame and the wall.
NOTE: You must install the Tipping Restraint Hardware with the unit to prevent
the unit from tipping, causing any accidents or damage to the unit.
25.The console is now ready for use. Swivel the TV left-or-right for optimum viewing control.

Page 19
Care and Maintenance
zUse a soft, clean cloth that will not scratch the surface when dusting.
zUse of furniture polish is not necessary. Should you choose to use polish, test first in an
inconspicuous area.
zUsing solvents of any kind on your furniture may damage the finish.
zNever use water to clean your furniture as it may cause damage to the finish.
zAlways use coasters under beverage glasses and flowerpots.
zLiquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
zAlways use protective pads under hot dishes and plates. Heat can cause chemical changes that
may create spotting within the furniture finish.
zStains or marks from crayons or ink markers will be difficult to remove.
zIn the event that your furniture is stained or otherwise damaged during use, we recommend that
you call a professional to repair your furniture.
zCheck bolts/screws periodically and tighten them if necessary.
Further advice about furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and
humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep
furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important
and helpful tips will enhance your furniture as it ages.
A Touch-up Pen has been provided to repair any small nicks or scratches that may occur
during assembly or shipping.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your purchase.

IF YOU NEED TO ORDER REPLACEMENT PARTS, PLEASE USE THE LIST BELOW
4
12
3
5
6
7
8
9
10
12
13
14
15 16 22
26 28
29 30
31 32
34
25
35
37
27
23
19
33
* 1-LSF Left Side Frame * 15-SB Swiveling Bracket * 29-1 1/4B 1-1/4" Bolt
* 2-RSF Right Side Frame * 16-MF Mounting Frame * 30-1 5/8B 1-5/8" Bolt
* 3-BP Back Panel * 17-MB Monitor Bracket * 31-2 1/4B 2-1/4" Bolt
* 4-BTF Back Top Frame * 18-LB Lock Bolt * 32-HN Hex Nut
* 5-BBS Back Bottom Stretcher * 19-SPEC Small Plastic End Cap (15 x 15 mm) * 33-LW Lock Washer
* 6-TC Top Crossbar * 20-MPEC Medium Plastic End Cap (20 x 20 mm) * 34-FW Flat Washer
* 7-TS Top Stringer * 21-LPEC Large Plastic End Cap (20 x 40 mm) * 35-#4x10S #4 x 10 mm Screw
* 8-MC Middle Crossbar * 22-CW Cable Wheel * 36-OW Open Wrench
* 9-MS Middle Stringer * 23-FL Floor Leveler * 37-M4AW M4 Allen Wrench
* 10-BB Bottom Brace * 24-LFP Left Front Post * 38-TUP Touch-up Pen
* 11-BS Bottom Stringer * 25-RFP Right Front Post * 39-TRHK Tipping Restraint Hardware Kit
* 12-TG Top Glass * 26-SC Suction Cup * TVMK TV Mounting Kit
* 13-MGS Middle Glass Shelf * 27-5/8B 5/8" Bolt * CH Complete Hardware
*
14
-
BGS
Bottom Glass Shelf
*
28
-
3/4B
3/4
"
Bolt
11
18
17
24
37
36
20
21
38 39
14BGS
Bottom
Glass
Shelf
283/4B
3/4
Bolt
Flat Panel TV Stand