Whalen BBAVC66-GB User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2020-08-28 Rev. 0001-A
66” TV Stand
Model # BBAVC66-GB
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenfurniture.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: 66” TV Stand
MODEL # BBAVC66-GB
1. Please read the Assembly Instructions prior to assembling this product.
2. Remove all hardware from the box and sort by size.
3. Check to see that all hardware and parts are present BEFORE assembling.
4. Ask a friend to assist you with the assembly of this furniture.
5. To avoid damage, assemble the product on a sturdy, level and protective surface.
6. Please wait until all steps are completed before fully tightening bolts.
7. Make sure all bolts are tightly fastened before the unit is used.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
G E N E R A L I N F O R M A T I O N , T I P S
AND
T R I C K S
This product is sold with one set of Tipping Restraint Hardware Kit. You must install the Tipping Restr
aint
Hardware between the wall and the console to prevent any accidents or damages
. When properly installed,
this restraint can provide protection against the unexpected tipping of the unit due to small tremors, bumps
or
climbing. The restraint is only a deterrent and is not a substitute for proper adult supervision. Use of tip-
over
restraints may only reduce, but not eliminate, the risk of tip-over.
MAXIMUM LOAD 22.7 kg / 50 lb.
FITS UP TO MOST 203.2 cm / 80”
DIAGONAL FLAT PANEL TVs
MAXIMUM LOAD 61.2 kg / 135 lb.
THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT
PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO
AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE BASE OF THE
TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT
OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS
INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS
COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY. FOR USE WITH
TELEVISIONS WEIGHING 135 LBS (61.2 KG) OR LESS. USE WITH HEAVIER TELEVISIONS MAY RESULT
IN INSTABILITY CAUSING TIP OVER RESULTING IN DEATH OR SERIOUS INJURY.
PLACE TV BEHIND THE STOPPER

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Top Glass (Qty. 1) B- Glass Shelf (Qty. 2)
C- Leg (Qty. 2) D- Top Frame (Qty. 1)
E- Middle Frame (Qty. 1) F- Bottom Frame (Qty. 1) G- Back Frame (Qty. 1)
(1) 1/4” x 38 mm Bolt (2) 1/4” x 28 mm Bolt (3) 1/4” x 15 mm Bolt
(Qty. 18+1 extra) (Qty. 4+1 extra) (Qty. 2+1 extra)
(4) Lock Washer (5) Flat Washer (6) Glass Riser (7) Velcro Strip
(Qty. 22+1 extra) (Qty. 22+1 extra) (Qty. 4) (Qty. 2)
(8) Glass Bumper (9) Acrylic Stopper Hex Wrench Tipping Restraint Hardware Kit
(Qty. 16+1 extra) (Qty. 1) (Qty. 1) (Qty. 1)
(Included in Plastic Bag)
Tools required (not included): Phillips screwdriver, stud finder, pencil, tape measure, power drill and
1/8" drill bit.

4
Assembly Instructions
NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back
and fully tighten all bolts. This will make the assembly easier.
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Locate the Back Frame (G) on a level and protective surface with the flush surface facing up.
3. Fasten the Middle Frame (E) to the Back Frame (G) with two 38 mm Bolts (1) and four Washers (4 and
5).
④×2
⑤×2
①×2
5
4
1
1
5
4
E
G

5
Assembly Instructions
4. Repeat the previous step to fasten the Bottom Frame (F) to the Back Frame (G).
④×2
⑤×2
①×2
G
1
1
5
45
4
F
E

6
Assembly Instructions
5. Align and attach one Leg (C) to the Middle Frame (E) and Bottom Frame (F) with four 38 mm Bolts (1)
and eight Washers (4 and 5) as shown.
④×4
⑤×4
①×4
G
F
E
145
C

7
Assembly Instructions
6. Fasten the Top Frame (D) to the Leg (C) with two 38 mm Bolts (1) and four Washers (4 and 5) as
shown.
④×2
⑤×2
①×2
The threaded sockets for
risers on the opposite side
D
F
E
C
145

8
Assembly Instructions
7. Attach the other Leg (C) to the Shelf Frames (D, E and F) with six 38 mm Bolts (1) and twelve Washers
(4 and 5).
④×6
⑤×6
①×6
C
D
F
E
C
541

9
Assembly Instructions
8. Stand the assembled unit upright.
9. Fasten the Back Frame (G) to the Top Frame (D) with two 38 mm Bolts (1) and four Washers (4 and 5).
④×2
⑤×2
①×2
G
D
C
C
1
4
5

10
Assembly Instructions
10. Securely screw four Glass Risers (6) into the drilled holes on the Top Frame (D) as shown.
⑥×4
D
6
C
C

11
Assembly Instructions
11. Place the Top Glass (A) onto the Top Frame (D) and make sure the threaded sockets on the metal plates
overlap the drilled holes properly. Insert four 28 mm Bolts (2) with the Washers (4 and 5) through the
drilled holes and securely screw into place.
④×4
⑤×4
②×4
C
C
D
G
A
2
4
5

12
Assembly Instructions
12. Now, go back and securely tighten all the bolts. Make sure that all the parts are tight and there are no
gaps between the parts. This will keep the unit square.
13. Attach two Velcro Strips (7) to the backside of the Back Frame (G) with the 15 mm Bolts (3). Tighten
the bolts with the enclosed hex wrench.
NOTE: You can use the velcro strips to help keep your entertainment center’s cables and cords
organized.
③×2 ⑦×2
A
C
C
3
7
G
7
7

13
Assembly Instructions
14. Evenly stick sixteen Glass Bumpers (8) on the Middle and Bottom Frames (E and F).
15. Place the Glass Shelves (B) onto the Glass Bumpers (8) and push the glass shelves all the way back
against the Back Frame (G).
NOTE: Make sure that the glass sits correctly. If glass is scratched, you can minimize the damage by
using a BLACK marker and filling in scratched area from underneath.
⑧×16
E/F
C
C
A
B
B
8
E/F
E
F
B
8

14
Assembly Instructions
NOTE: To prevent your TV from tipping, you must install the acrylic TV stopper if you place a flat
panel television on the top of your stand. Otherwise, skip to Step 17.
16. Remove the paper backing from the Acrylic Stopper (9) and place it in the cut-out of the acrylic stopper
template on the front of the Top Glass (A). Make sure it is properly aligned before applying pressure.
17. Remove the acrylic stopper template carefully.
⑨×1
A
A
A

15
Assembly Instructions
Tools required (not provided): Phillips screwdriver, stud finder, pencil, tape measure, power drill and
1/8" drill bit.
18. Position the assembled unit at the desired location against a wall. If necessary, adjust the pre-attached
Floor Levelers at the bottom of the Legs (C) to level the unit.
19. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to
attach the tip-over restraint to the Back Frame (G) and the wall.
NOTE: The tipping restraint hardware included is for wooden stud wall construction. It must be
attached to a wall stud. Depending upon your wall construction, different anchor hardware maybe
required. Please contact your local hardware store for assistance. Young children can be seriously
injured by tipping furniture. You must install the tipping restraint hardware with the unit to prevent the
unit from tipping, causing any accidents or damage. The tipping restraints are intended only as a
deterrent, they are not a substitute for proper adult supervision. The tipping restraints are not
earthquake restraints. If you wish to add the extra security of earthquake restraints, they must be
purchased and installed separately.
20. The TV stand is now ready for use.
Wooden stud
Wall
Floor leveler
Long screw
Metal bracket
Unscre
wed
b
olt
Nylon strap
C

16
Metal Furniture Care Instructions
 For everyday cleaning, chrome, brass, aluminum, and painted metal surfaces can be kept looking their best
by wiping with a slightly damp, soft cotton cloth, or vacuum cleaner brush.
 If soiled, wipe with clean sponge or cloth wrung out of water. Wipe dry with cloth or paper towel to avoid
water spots.
 Do not use any harsh abrasives or chemicals to clean any metal surfaces as it may damage the protective
coating.
 Metal will rust if the finish is scratched or if your furniture is exposed to excessive humidity, particularly
in salt water locations.
 Most metal furniture has a protective coating to prevent rust, however rust may occur if the finish is
marred or wears away over time.
 Stains or marks from crayons or ink markers will be difficult to remove.
 In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a
professional to repair your furniture.
 Check Bolts/screws periodically and tighten them if necessary.
Further Advice about Metal Furniture Care
It is best to keep your furniture in a climate controlled environment. Continual exposure to damp and wet
environment can cause corrosion. It is advised to keep furniture away from direct sunlight as it may damage the
finish. Indoor furniture is not recommended for outdoor use.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful
tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or
replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet
your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state
or province to province.
Whalen Furniture Manufacturing
1578 Air Wing Road, San Diego, CA 92154, USA
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE SEGURIDAD.
POR FAVOR LEA Y MANTENGA PARA USO FUTURO.
Fecha 2020-08-28 Rev. 0001-A
Consola para TV de 66”
Modelo # BBAVC66-GB
ENSAMBLE POR ADULTO REQUERIDO
Si tiene alguna pregunta acerca del ensamble o si le hace falta alguna parte, no devuelva este producto
a la tienda donde lo compró. Por favor llame a nuestro departamento de ayuda al cliente teniendo su
instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica:
1-866-942-5362
Hora estándar del Pacífico: 8:30 a.m. - 4:30 p.m., Lunes-Viernes
O nuestra página de Internet 24hrs al día, 7 días a la semana para asistencia en el producto:
www.whalenfurniture.com
O mande su requerimiento por correo Eléctronico a [e-mail]
NÚMERO de LOTE:
FECHA de COMPRA: / /

2
FABRICANTE: Whalen Furniture Manufacturing
CATALOGO: Consola para TV de 66”
MODELO # BBAVC66-GB
1. Por favor lea el instructivo antes de comenzar el ensamble.
2. Retirar todo el material de ferretería de la caja y ordenar por tamaño.
3. Asegurar de que todo el material de ferretería y partes estén presentes ANTES del ensamble.
4. Pedir asistencia de un amigo para ensamblar la unidad.
5. Para evitar daños, ensamblar el producto en una superficie fuerte, nivelada y protegida.
6. Esperad hasta que todos los pasos estén completos antes de apretar los pernos.
7. Asegurar de que los pernos estén apretados antes de usar la unidad.
MÁ X I M O P E SO R EC O M E N D A D O
I N F O R M A C I Ó N G E N E RA L , R E C O ME N D A C IO N ES Y T R U C O S
Esté producto se vende con un juego de restricción de movimiento. Usted debe instalar el
juego de restricción
de movimiento entre la pared y la consola de TV para prevenir accidentes o daños. Cuando está
instalada
correctamente, este tope de movimiento puede proveer protección en contra el inclinamiento inesperad
o de la
unidad a causa de pequeños temblores, golpes. El tope de movimiento es solo un imp
edimento, no hay
substituto para la supervisión adulta. El uso del tope de movimiento puede reducir, pero no eliminar, el ries
go
de voltearse la unidad.
CARGA MÁXIMA 22.7 kg / 50 lb.
PARA TVs DE PANTALLA PLANA
DE HASTA 203.2 cm / 80” EN DIAGONAL
CARGA MÁXIMA 61.2 kg / 135 lb.
PONER LA TV DETRÁS DEL TOPE
ESTA UNIDAD NO DEBE UTILIZARSE CON TELEVISIONES CRT O DE TUBO.
UTILIZARSE ÚNICAMENTE CON TELEVISIONES DE PANTALLA PLANA Y EQUIPO DE AUDIO/VIDEO
QUE TENGA LA MEDIDA/PESO RECOMENDADO. NUNCA UTILIZAR CON TELEVISIONES MÁS
GRANDES/PESADAS DE LAS RECOMENDADAS. PARA EVITAR INESTABILIDAD COLÓQUELA EN EL
CENTRO DE LA UNIDAD; LA BASE DE LA TELEVISIÓN DEBE DE REPOSAR SOBRE LA SUPERFICIE
DE SOPORTE DE LA UNIDAD SIN REBASAR LAS ORILLAS. LAS TELEVISIONES DE PANTALLA
PLANA COLOCADAS INAPROPIADAMENTE, O LAS TELEVISIONES DE PANTALLA PLANA
INCLUYENDO EQUIPO QUE SOBREPASA LAS MEDIDAS Y PESOS RECOMENDADOS PUEDEN
CAERSE Y/O ROMPER LA UNIDAD, CAUSANDO POSIBLES DAÑOS O LESIONES. PARA USO DE
TELEVISIONES DE HASTA 135 LBS (61.2 KG) O MENOS. USO CON TELEVISIONES DE MAYOR PESO
PUEDE RESULTAR EN INESTABILIDAD CAUSANDO QUE LA UNIDAD CAIGA EN ALGUNOS CASOS
PROVOCAR DAÑOS O MUERTE.

3
Lista de partes y material de ferretería
Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de
ferretería antes de iniciar el ensamblado.
A- Vidrio superior (Cant. 1) B- Repisa de vidrio (Cant. 2)
C- Pata (Cant. 2) D- Marco superior (Cant. 1)
E- Marco medio (Cant. 1) F- Marco medio (Cant. 1) G- Marco posterior (Cant. 1)
(1) Perno de 1/4” x 38 mm (2) Perno de 1/4” x 28 mm (3) Perno de 1/4” x 15 mm
(Cant. 18+1 extra) (Cant. 4+1 extra) (Cant. 2+1 extra)
(4) Arandela de presión (5) Arandela plana (6) Elevador de vidrio (7) Banda de velcro
(Cant. 22+1 extra) (Cant. 22+1 extra) (Cant. 4) (Cant. 2)
(8) Tope de vidrio (9) Tope de acrílico Llave hexagonal Juego de restricción de movimiento
(Cant. 16+1 extra) (Cant. 1) (Cant. 1) (Cant. 1)
(Incluido en bolsa de plástico)
Herramientas requeridas (no incluidas): Desarmador estrella, buscador de vigas, lápiz, cinta métrica,
taladro, y broca de 1/8".

4
Instrucciones de ensamble
Nota: Por favor no apriete completamente todos los pernos, hasta que termine con el ensamble de las
partes, después asegúrese de apretar todos los pernos, esto hará el ensamble más fácil.
1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas.
2. Localizar el marco posterior (G) en una superficie nivelada y protectora con la superficie nivelada hacia
arriba.
3. Sujetar el marco medio (E) al marco posterior (G) con 2 pernos de 38 mm (1) y 4 arandelas (4 y 5).
④×2
⑤×2
①×2
1
5
4
E
G
5
4
1