Wharfedale Pro Vardus User manual

VARDUS
Loudspeaker Systems
Instruction Manual
BRITAIN'S MOST FAMOUS LOUDSPEAKERS

Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning: To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture. The product must not be exposed to dripping
and splashing and no object filled with liquids such as a vase of flowers
should be placed on the product.
No naked flame sources such as candles should be placed on the
product.
Caution: Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this device.
Warning: The mains power switch for this appliance is located on the
rear panel. To permit free access to this switch, the apparatus must be
Read these instructions. located in an open area without any obstructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wider blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Use only attachments/accessories specified by the manufacturer.
Use only with a cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution Class II construction double insulated.
when moving the cart/ apparatus combination to This product must not be connected to earth.
avoid injury from tip-over.
ESSENTIAL INFORMATION FOR UK USERS
The power cord on your subwoofer may be supplied with a plug
incorporating a fuse, the value of which is indicated on the pin face of
the plug. Should the fuse need to be replaced, an ASTA or BSI approved
BS1362 fuse must be used of the same rating. If the plug is cut off it
must NOT be re-used. Dispose of any such plug safely. There is a danger
of electric shock if a cut-off plug is inserted into a mains socket.
The wires in the mains lead are coloured in accordance with the
following code: Blue - Neutral: Brown - Live.
As the colours of the wires in the mains lead may not correspond with
the markings identifying the terminals in the replacement mains plug,
proceed as follows:
The wire coloured Blue
must be connected to the
terminal marked with the
letter ‘N’ or coloured
Black. The wire coloured
Brown must be connected
to the terminal marked
with the letter ‘L’ or
coloured Red.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-REMOVEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED PERSONNEL
CAUTION!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ADVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE-
NE PAS OUVRIR
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
IMPORTANT SAFETY INFORMATION
FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
2

Before making any connections, switch all the units in
your system off at the mains.
Set the volume control at minimum when you switch on
your system or change sources, and turn the level up
gradually.
DO NOT use your amplifier at full volume.
Ensure that all loudspeakers in the system are correctly
wired.
DO NOT subject your loudspeakers to excessive cold, heat,
humidity or sunlight.
DO NOT place heavy objects on top of loudspeakers
DO NOT connect speaker terminals to the mains supply.
DO NOT dismantle the loudspeaker. There are no user
serviceable parts inside it and you will void the warranty.
Before installing this product
read all these instructions!
PRELIMINARIES
UNPACKING YOUR LOUDSPEAKERS
After taking out the top packing piece, lift the loudspeakers
and accessories from the carton. Remove all the protective
bags. Do NOT lift the loudspeakers out using the bags.
Accessories provided with each loudspeaker are as follows:
VR-200, 300, 400
!One set of spikes with mounting hardware.
!One set of rubber feet
VR-50, 100
!One set of rubber feet
VR-CEN 1, CEN 2
!No accessories needed
VR-SURR 1, SURR 2
!No accessories needed
VR-10 SUB
!Four floor spikes (attached to the subwoofer)
!IEC power cord suitable for your location
Check all items after unpacking. If any item is missing or
damaged, immediately contact your Wharfedale dealer.
Retain the packaging. If you dispose of the packing, follow
all recycling regulations in your area.
PREPARATIONS FOR INSTALLATION
Before connecting your system consider where you will place the
speakers in the room. This is particularly important if you are
wall mounting the centre or surround loudspeakers.
CONNECTORS AND CABLES
Stereo systems require two lengths of two core cable. 5.1 and
7.1 installations require 5 and 7 lengths respectively.The cables
VR-50, 100: These loudspeakers are designed to be connecting the Front loudspeakers should be the same length
mounted on a rigid floor stand. The loudspeaker may also be and the cables connecting the Surround (and Rear) speakers
placed on a sturdy shelf or wall mounted on a suitable wall should also be of equal length. We suggest you use audio cable
bracket. Consult your dealer for advice if you are in any doubt. and not general purpose ‘bell’ or ‘zip’ wire.
VR-10 SUBWOOFER:
VR-200, 300, 400: These are floorstanding models. For
improved performance the loudspeakers are spike coupled to Ensure there is a mains point within easy reach of the unit.
the floor. Rubber feet are provided as an alternative. You will need to purchase a suitable RCA interconnect cable to
connect the subwoofer to your pre-amplifier or A/V amplifier
VR-CEN, CEN 2; VR-SURR 1, SURR 2: The centre
(see page11). This cable must be a high quality fully screened
and surround loudspeakers are intended to be operated
cable. Poorly screened cable is liable to pick up stray hum and
attached to the wall via keyhole mounts in the rear of the
interference fields and should be avoided.
loudspeaker (see Page 6). Fixings for attaching the
loudspeakers to the wall are not supplied. CAUTION: When running cables to loudspeakers, do not trail
them across open floors where they can be a source of danger.
Route them safely, around room boundaries if necessary.
3
PREPARATION FOR INSTALLATIONPREPARATION FOR INSTALLATION

PREPARING FLOORSTANDING LOUDSPEAKERS
4
POSITIONING STEREO LOUDSPEAKERS
The VR-200, 300, and 400 are floor standing. We suggest that walls, the inward angle may be increased by up to 40%, but this
they are positioned at least 200 mm from the rear walls and 700 may restrict the width of the optimum listening position.
mm from the side walls, facing slightly inwards. The VR-50 and A rule of thumb is that the listener should be as far from the
100 should be stand or wall mounted or placed on a rigid shelf. loudspeakers as they are from each other. The speakers should
The bass extension will improve if smaller speakers are ideally be positioned so that the treble units are roughly at ear
operated closer to the rear walls. If the loudspeakers are placed level to a seated listener. As personal taste plays a large role,
too close to the walls the bass will increase but may be boomy experiment with different configurations and play a wide range
and indistinct. If the loudspeakers are placed away from the of programme before finalising the position of your speakers.
2 - 4 metres
º
0
4
-
5
1
>0.7metre
VR-200-400
>200 mm
VR-50, 100
>50 mm
Place a soft cloth on the floor to protect the speaker. Invert the
ATTACHING THE SPIKES
loudspeaker and place it on the cloth.
CAUTION: SPIKES ARE SHARP. Thread a locking nut two-thirds of the way up the spike. Place a
Make sure that there are no wires or hidden obstacles that washer over the spike and insert each spike assembly into a
could be damaged by the spikes in the immediate spike mount on the loudspeaker. Tighten the nut finger tight so
operational area of the speakers. that the spike is secure but not locked in place.
NEVER drag a loudspeaker on its spikes. Always lift it. If the LEVELLING THE LOUDSPEAKER
item is heavy get assistance.
After all the spikes are attached, invert the loudspeaker and
place it carefully on the floor. Place a spirit level on the speaker
Loosen the nut on each spike one turn. If the floor is not perfectly
level you will find that one spike is off the ground. Starting with
this spike, unscrew it so that it touches the floor. Move the other
spikes in and out so the speaker does not wobble and is level
front and back and sideways. Now tighten the nuts to lock the
spikes firmly in position
A set of rubber feet is provided as an alternative to spikes.

SUB
POSITIONING HOME CINEMA LOUDSPEAKERS
2-4 metres >150 mm
>200 mm
2-4 metres >150 mm
>200 mm
400 mm
1 m
5.1 POSITIONING
Place the front speakers as shown. Front
loudspeakers should be placed away from
walls for best results. Angling the speakers
inward slightly will improve stereo images but
too extreme an angle will impair movie sound.
The VR-100 200 and 300 loudspeakers must
be placed at least 450mm from a TV screen. The
VR-50 may be operated close to a TV screen.
The VR-CEN 1 and CEN 2 centre speakers can
be placed above or below the TV screen.
Place the VR-10 SUB subwoofer as close to the
wall as you can, leaving just enough space to
operate the controls and mains switch. Room
positioning is not critical but we recommend
that it is placed in front of the listening seat.
Never operate the subwoofer within 450mm of
a conventional TV screen.
The surround speakers should be placed above
and behind the listening seat. They may be
mounted on the side walls or on the rear walls
but always behind the listener. Do not operate
them within 450mm of a TV screen.
If the distance between the side walls is too
great, you could use a second pair of stand
mounted or floorstanding loudspeakers as the
surround loudspeakers, placed as shown in the
drawing opposite.
7.1 POSITIONING
If you are using a 7.1 system, the back
loudspeakers must be at least 1 metre behind
the listening seat.
WALL MOUNTING POSITIONS
If you are wall mounting the centre and effects
loudspeakers we recommend that they be
mounted as shown.
Wall mounting the centre channel loudspeaker
below the screen is not recommended for fixed
installations.
CENTRE
CENTRE
5
5.1 SYSTEM
7.1 SYSTEM
SUB
WALL MOUNTING POSITIONS

CONNECTING YOUR LOUDSPEAKERS - 1
TERMINAL PANELS
All the loudspeakers connect to
the amplifier via a twin
terminal connecting panel. The
positive terminal is located at
the right of the panel and is
coded Red, The Negative
terminal is coded Black.
The VR-SURR 1 uses spring
loaded push terminals. All the
other models use screw
terminals.
--
VR-SURR 1 VR-SURR 2
CABLE PREPARATION ALL OTHER MODELS
Prepare a suitable length of loudspeaker cable for each unit. Unscrew a terminal. Thread the bared end of each cable
Split the twin cores to a depth of about 40mm. Carefully strip the through the hole in the bottom of the terminal post. Ensure that
insulation from each end, leaving about 8mm of bare wire. If there are no loose strands which may touch adjacent terminals.
the cable is stranded, lightly twist to gather any loose strands. Retighten the terminal securely.
Audio cable is polarised, with two cores of different colours, or
often a coloured tracer or identification rib. We suggest that you
connect the coloured/striped wire to the RED, Postive terminals
of your AV amplifier. This will ensure that all the loudspeakers AMPLIFIER - SPEAKER CONNECTIONS
are connected the correct way round and avoid set-up problems.
Connect each loudspeaker to the correct channel of your
CONNECTING THE VR-SURR 1 amplifier or AV processor taking care to connect the Red,
Press down on a terminal lever Positive (+) terminal of the speaker to the Red, Positive (+)
terminal of the speaker output terminal of the amplifier, and
similarly with the Black, Negative (–) terminal. Use the
connection diagrams on the next page to help you.
WALL MOUNTING
If you are wall mounting speakers please follow this procedure.
1: Run the cable from the amplifier to the speaker location.
2: Connect the cable to the loudspeaker.
3: Hang the loudspeaker on the wall.
4: Connect the loudspeaker cable to the amplifier.
. Insert the wire into the terminal.
Release the lever. Ensure that the terminal grips the bare wire at
the end of the cable, not the insulation.
40mm
8mm
7
c
b
ALL OTHER MODELS
--

L
R
FRONT RIGHT FRONT LEFT
CONNECTING YOUR LOUDSPEAKERS - 2
STEREO CONNECTIONS
ROOM PLACEMENT
8
CENTRE
LL
RC
R
FRONT RIGHT FRONT LEFT
SURROUND LEFT
SURROUND RIGHT
5 CHANNEL CONNECTIONS
ROOM PLACEMENT

Dolby Labs Recommended 7.1 Placement (Single Back channel for 6.1 shown dotted)
7 CHANNEL CONNECTIONS & PLACEMENTS
9
Left Surround
Left Back
90º
110º
135º
150º
22º 30º
LFE
Centre
Right Back
Right Front
Left Front
Right Surround
CENTRE
LL
RRC
RL
FRONT RIGHT FRONT LEFT
SURROUND LEFTSURROUND RIGHT
BACK RIGHT BACK LEFT
7 CHANNEL CONNECTIONS
ROOM PLACEMENT

PRELIMINARIES
Open the carton and remove all the top packing pieces. Lift the
subwoofer out taking care not to damage the cabinet. DO NOT
lift the subwoofer out of the carton using the protective bag. The
unit is heavy; if you cannot manage it easily, get assistance.
Retain the packing materials. If you decide not to keep the
packing, please dispose of it having regard to any recycling
regulations in your area. Please retain the user manual. If you
transfer this equipment to a third party, please ensure all the
instructions are passed on with the product.
POWER CONNECTIONS
This subwoofer is factory set to operate from the mains voltage
marked on the amplifier panel. Before connecting check this
voltage is correct for your mains supply.
!230 volt products - 220 volts to 240 volts
!115 volt products - 110 volts to 120 volts
If you move to an area with a different mains supply, consult your
Wharfedale dealer for advice.
REAR PANEL CONNECTIONS
PLACEMENT
Although the unit may be placed almost
anywhere in the room, we recommend that is
placed in front of the listener central to the
listening position. There should be a mains
outlet within easy reach.
The bass port is mounted under the subwoofer
firing downward and moves a lot of air at high
volume, so make sure the floor is sound. The
subwoofer is front-firing so do not place it
behind surfaces or objects that may rattle.
10
INSTALLING THE VR 10 SUBWOOFER
SERIAL No.:
LINE LEVEL
INPUT OUTPUT
OFF ON
AC INPUT POWER
PHASE
AUTO
POWER
OFFON
180º0º
~230V/50Hz 150W
FUSE
T2A 250V
LEFT RIGHT
VOLUME
RIGHT
LEFT
FREQUENCY
CROSSOVER
SPEAKER LEVEL INPUTS
!
N
11189
O
35
45
55 65
75
85
(Hz)
FUSEFUSE
FREQUENCY
CROSSOVER
FREQUENCY
VOLUME
CROSSOVER
WHARFEDALE INTERNATIONAL HUNTINGDON, UNITED KINGDOM
SUB-WOOFER AMPLIFIER
CAUTION:
DISCONNECT SUPPLY CORD
BEFORE CHANGING FUSE.
REPLACE ONLY WITH SAME
TYPE FUSE AND RATING
ATTENTION:
REPLACER LE FUSIBLE.
UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE
ET CALIBRE
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE
b Volume Control
c Crossover Frequency Control
d Phase Control
e Auto Power Switch
f Power ON/OFF Switch
g Mains Power Fuse
h IEC Mains Input Socket
i Speaker Level Inputs
j Line Level Inputs
1) Line Level Outputs

CENTRE FRONTREAR
LEFTLEFT RIGHTRIGHT
Subwoofer Out
(Line Level)
AV AMPLIFIER
INSTALLING THE VR 10 SUBWOOFER - 2
A/V PROCESSOR CONNECTIONS
Your subwoofer has been designed for optimum
performance with a Digital processor. If your AV
processor has a line level or LFE subwoofer output you
should use this connection. You will need to purchase a
single screened RCA phono lead from your dealer.
Connect this lead to the Left line input of the Subwoofer
as shown below
Alternatively, you may use a split mono lead from the
processor to both inputs of the subwoofer. In this case
the input level at the subwoofer will be slightly higher.
STEREO LINE CONNECTIONS
If your amplifier has a spare preamplifier output or a
stereo sub-woofer output, connect the sub-woofer as
shown. You will need a stereo screened RCA phono
cable.
PRE OUT - MAIN IN CONNECTIONS
If you use a stereo pre and power amplifier, or a stereo
amplifier where the pre and main amplifier can be
separated, connect the sub-woofer as shown. There are
two alternative methods.
A: You will need two screened RCA ‘Y’ adaptors and
two single RCA phono cables.
Remove the Pre-Main links on your amplifier. Connect
the socket (common) of an RCA ‘Y’ adaptor to one of
the mono cables. Connect one leg of the ‘Y’ adaptor to
the Left Channel Pre Out socket on the amplifier and
the other leg to the Left Channel Main In socket.
Connect the remaining plug to the Left Channel Line
Level Input on the subwoofer. Repeat for the Right
Channel.
B: You will need two stereo screened RCA cables.
Connect a Stereo cable from the Line Level Inputs of
the sub-woofer to the Pre Out sockets of the amplifier.
Now connect a second Stereo cable from the Line Level
Outputs of the sub-woofer to the Main In sockets of the
amplifier. The sub-woofer is now inserted in the system
loop.
CENTRE FRONTREAR
LEFTLEFT RIGHTRIGHT
CENTRE FRONTREAR
LEFTLEFT RIGHTRIGHT
Subwoofer or Pre Out
(Line Level)
AV AMPLIFIER
L
R
LEFTRIGHT
AMPLIFIER
L
R
PRE
OUT MAIN
IN
(x2)
11
LEFTRIGHT
AMPLIFIER
L
R
PRE
OUT MAIN
IN

RIGHT LEFT
FRONT RIGHT FRONT LEFT
SUBWOOFER
SPEAKER LEVEL INPUTS
LEFT RIGHT
SPEAKER LEVEL CONNECTIONS
The high level Speaker connections should be used only
if your amplifier does not have a line level subwoofer
output. In this connection the subwoofer is fed together
with the Front loudspeakers. For this you will need two
extra twin core cables.
Measure out two loudspeaker cables of the appropriate
length. Prepare the cables as described on Page 7.
Connect the Left Speaker Terminals on the sub bass unit
to the Front Left speaker terminals on the amplifier.
Connect the Red (+) speaker terminal on the amplifier
to the Red (+) terminal on the subwoofer. Connect the
Black (-) speaker terminal on the amplifier to the Black
(-) terminal on the subwoofer. Now connect the Right
Speaker terminals on the subwoofer to the Front Right
speaker terminals of the amplifier.
INSTALLING THE VR 10 SUBWOOFER - 3
Although the unit may be placed almost anywhere in the room, lacing
even behind the sofa or the TV set, we recommend that it be across a room corner will increase the bass further,
placed in front of the listener and as central to the listening possibly at the expense of clarity. Experiment with a variety of
position as possible. The subwoofer should not be operated locations and sources before making a final decision.
within 450mm of a television set as the drive unit magnet may Your system will perform best if there is a clear line of sight
distort the picture. between the subwoofer and the listening position.
NOTE: When running signal cables to the subwoofer, keep them
clear of obstructions. Do not run a long signal cable close to
A position close to the wall will enhance the bass; mains cables or cables carrying heavy digital traffic.
to a distance of about 200mm from the wall. P the
subwoofer
Place the VR-SUB subwoofer as close to the wall as you can,
leaving just enough space to operate the controls and mains
switch. If the
bass is excessive you can move the subwoofer out from the wall
POSITIONING THE VR-10 SUBWOOFER
12

VR 10 SUBWOOFER - OPERATION
SETTING UP HOME THEATRE TOPICS
!Set the subwoofer power switch to OFF. As the ear is unable to detect the direction from which deep bass
originates, this allows freedom in positioning the subwoofer.
!Turn the system Volume Control to minimum.
Varying the distance from the wall alters the amount of bass.
!Re-check all system connections. Some prefer to place the subwoofer against a room corner. This
!Connect the supplied subwoofer power lead to the IEC arrangement gives more bass at the possible expense of clarity.
power socket on the subwoofer and connect the mains plug
LOUDSPEAKER SIZES
into the wall socket.
!Set the subwoofer volume control midway (12o'clock) Many digital AV processors require you to specify the size of
!Switch on the mains power. speakers in the various channels. These are usually ‘Large’ or
‘Small’. We recommend that you set the centre and surround
FINE TUNING speakers to 'Small'. This will direct all the bass in the system to
Switch on the subwoofer power switch. Check that the power the subwoofer and provide clean, deep and louder bass.
indicator on the front of the cabinet glows. Now switch on the Set the VR-50, 100 and 200 to “Small” The VR-400 should be set
system. Play a programme with extended bass and set the to “Large”. We recommend the VR-300 be set to “Large” though
system volume to a reasonable level. Adjust the subwoofer if the bass is excessive, you may wish to set it to “Small”.
volume control to produce the desired level of bass.
Set the ‘Subwoofer’ option on the processor to 'On’ or 'Yes'.
PHASE SWITCH: If the bass is indistinct or lacks depth, the Phase
switch may need adjustment. Set the switch to 0º and listen SETTING LEVELS
carefully to some music with extended bass. If there is Once the loudspeaker settings have been finalised, put the AV
insufficient bass output from the sub-woofer set the Phase amplifier into its “Test” mode (see your processor instructions),
switch to 180º. Select the position which produces the most Adjust the levels until all channels are equally loud.
natural, extended bass. You may need to adjust the subwoofer output level. Avoid
LOW PASS FILTER. This adjusts the blend between the setting too high a level or you will swamp the sound with bass
subwoofer and the main speakers. and enables the system to be which be tiring to listen to and may limit the subwoofer’s ability
set up for optimum bass performance. The higher settings are to respond to large bass transients. Set a sensible level going
for use with bookshelf loudspeakers, the lower settings for large into the subwoofer. The subwoofer volume control should be
floorstanding models. If you choose too low a setting with small between 12 o’clock and 3 o’clock .
speakers, there will be a ‘hole’ in the bass response; too high a LFE
setting with large speakers will result in the upper bass
The Low Frequency Effects channel was designed as an additional
becoming bloated.
bass channel with its own dedicated subwoofer. In practice
AUTO SWITCH. In normal mode the subwoofer is permanently however, if all the speakers are set to Small, the LFE channel will
on. This may result in low level hum or noise if the rest of the be combined with the bass from other channels and all this feeds
system is switched off and the subwoofer is left switched on. into the subwoofer. When you set the LFE level from your AV
processor, use care with this setting as the LFE channel may
contain powerful low frequencies which, although normal in a
cinema, may overload a domestic subwoofer.
If, during a programme, you hear popping or thumping noises
coming from the subwoofer, immediately turn the AV Processor's
volume level down and then back off the LFE level. If this does not
cure the problem, back off the volume level at the subwoofer.
Please read the relevant sections of your AV amplifier manual
When the system is not in use for extended periods, we suggest and familiarise yourself with the various issues. If you are
you switch off the subwoofer to protect it from switching noises unsure, consult your dealer for help.
caused by domestic appliances, etc.
Setting the AUTO switch to ON automatically turns the
subwoofer on when a signal is detected at any of the inputs and
turns it off (Standby Mode) after a period of inactivity. We
recommend the AUTO switch be set to ON for normal operation.
In AUTO mode the indicator on the front of the subwoofer will
glow RED when the unit is in Standby and GREEN when
operational. If your subwoofer is disconnected from the mains
or the Power switch is “Off”, the indicator will be extinguished.
13

6
365 x 224 x 255 mm
296 x 194 x 200 mm

250 75
8 110 110
35 85
17.4
350
107dB
48
87
300
300 100
5
35 85
31
400
110dB
8
00
100
325
240 x 164 x 115 mm

Wharfedale International Ltd., IAG House, Sovereign Court, Ermine Business Park, Huntingdon, Cambs PE29 6XU, England.
Tel:[phone] www.wharfedale.co.uk
Wharfedale is a member of the International Audio Group.
SERVICE AND WARRANTY
CARE AND MAINTENANCE AUTHORISED SERVICE CENTRES
UK
If you play the speakers with the grilles off exercise great care.
NEVER touch the drive units which are easily damaged. Wharfedale International Ltd. IAG House, Sovereign Court,
The loudspeaker cabinets can be cleaned with a damp cloth or Ermine Business Park, Huntingdon, Cambs PE29 6XU, England.
with a spray furniture polish and a soft cloth. Apply the spray Tel:[phone] Fax: [phone]
sparingly to the cloth and then polish the cabinet. Never apply ASIA
spray directly to the cabinet. IAG. Room 2310 - 2311, Press Building, Shennan Road C,
GUARANTEE & SERVICE Shenzhen, China.
Tel: [phone] Fax: [phone]
In the unlikely event that your unit develops a fault you should
return it to your Wharfedale dealer using the original packing USA
to ensure safe shipping. IAG America, Inc. 8440 154th Avenue NE, Redmond, Washington
The terms of your guarantee may vary in different countries but 98052 USA
in all cases the guarantee excludes: Tel: [phone] Fax: [phone]
All damage caused through accident, misuse, wear and tear, For information on other authorised service centres worldwide contact
neglect, incorrect installation, adjustment or repair by Wharfedale International in the U.K.
unauthorised personnel. Liability for damage or loss occurring A worldwide distributor list is available on the Wharfedale website:
in transit to or from the purchaser. www.wharfedale.co.uk
Wharfedale will not be liable for any consequential damage, Wharfedale has a policy of continuous product development and
loss or injury, arising from or in conjunction with this reserves the right to change specification without notice.
equipment. The name ‘WHARFEDALE' is a registered trademark of Wharfedale
International Ltd. Wharfedale is a member of the International
Audio Group