Whirlpool LE5760XS User manual

Use&CareGuide
Start button
Unt screen
LARGECAPACITY
AUTOMATICDRYERS
LE5760XSLG5761XS

Contents
Important Safety lnatructlons ........3
Additional safety instructions
and your responsibilities ................3
Operatlng lnatructlons
Starting your dryer -....................... 4
The automatic cycles .....................6
Timed drying ..................................7
Using fluff air ..................................7
Caring For Your Dryer
Cleaning the lint screen ..................8
Lint xTeen maintenance ................8
Cleaning the dryer ......................a...9
Lint removal .................................10
tfYouNeedservlceor
Assistance ...............................-... 12
Whlrlpool Automatic Dryer
Warranty .........................................16
01992 Whirlpwl Corporation
fl your dryer has a Consumer Buy
Guide label, remove ft. ft will be easier
to remove before the dryer is used. To
remove any remaining glue:
l Rub briskly with thumb to make a
ball, then remove.
or
l Soak area with liquid hand
dishwashing detergent before
removing glue as described above.
Do not use sharp instruments, rubbing
alcohol, flammable fluids or abrasive
cleaners. These can damage the finish.
See ‘Important Safety Instructions’ on
paw 3.
NOTE: Do not remove any permanent
instruction labels inside the dryer.
You should wipe out the dryer drum
with a damp doth before using to
remove dust from storing or shipping.
Thank you for buying a Whirlpool
appliance. Please complete and mail
the Owner Registration Card provided
with this product. Then complete the
form below. Have this information ready
if you need service or call with a
question.
l Copy model and serial numbers from
label (on the frame behind the door)
and purchase dafe from sales slip.
l Keep this book, the Dryer Guide and
the sales slip tog&her in a handy
place.
Model Number
!hdal Number
Purchul.0 Me
Smke~ CompanyPhoneNumber
FOR YOUR SAFETY
If you smell gas:
1. Open wlndows.
2 Don’t touch elect&al
switches.
3.lZZ;egulsh any open
4. lmmeblately call your ga9
suppller. 1
FOR YOUR SAFETY
Do not store or use gasoline
or other flammable vapors
and llqulds In the vlclnlty of
this or any other appliance.
The fumes can create a flre
hazard or exploslon.
2

ImportantSafetyInstructions
To reduce the rlsk of fire, electrkal sho& or
Injury to persons when uslng your dryer, follow
bask precautkns, lncludlng the followlng:
l Read all lnstructkns before uslng l You are responsible for maklng
the dryer. sure that your dryer is installed,
l NEVER dry items cleaned, washed, repaired and has parts replaced by a
soaked in or spotted with wax, paint, qualified person.
gasoline or flammable flubs in the l Use only fat& softeners specifiilly
dryer. The fumes can aeate a RRE labeled as not being harmful to the
HAZARD or EXPLOSION. ALWAYS dryer.
hand launder and air dry fabrics l FlRE HAZARD and f&RAGE to
containing these materials. materials can resuft from:
l NEVER allow children to operate,
play with or crawl inside the dryer. -drying rubber, rubber-like and heat
sensitive materials with heat.
Cbse supervision of children is
necessary when the dryer is used -allowing lint build-up inside the
near children. dryer or exhaust system. Cleaning
l DC NOT reach into a dryer if the should he done periodically by a
drum is moving. qualified person.
l Clean lint screen before or after
l When discarding an old dryer, each bad.
ALWAYS remove the door to
prevent accidental entrapment. l Do NOT let dust, lint, paper. rags,
l Do NOT install or store dryer where chemicals, etc. pile up around or
it will be exposed to the weather. under the dryer.
l DC NOT tamper with the controls. l Dryer must be electrically grounded.
See the Installation Instructions.
-SAVETHESEINSlRUCllOf4S-
Additionalsafetyinstructionsandyourresponsibilities
l NEVER operate the dryer if:
-it is not working right (i.e. noisy,
too hot).
-it is damaged.
-parts are missing (i.e. door latch).
-all panels are not in place.
-the lint screen is loose, damaged
or missing.
l ALWAYS shut off the gas valve
before leaving on vacation if you
have a gas dryer.
l ALWAYS unplug the power supply
cord or turn off electrbal power
before attempting to service the
dryer. Shut off GAS VALVE if you
have a gas dryer.
l You are responsible for maklng
sure that your dryer:
-is properly maintained.
-is properly installed and leveled on a
floor that can support the weight in a
well ventilated morn.*
-is locatedin an area wherethe
temperature is above 45°F (7%).
-is connected to the proper outlet and ‘-
electrical supply.’
-is properfy connected to fuel and
exhaust systems.’
-is not installed against drapes or
curtains.*
-is used only for jobs normally
expected of home dothes dryers.
-is not used hy anyone unable to
operate it property.
‘See the Installation lnstructbns for
complete information.
3

OperatingInstructions
Startingyourdryer
Be sure to refer to the chart below and the Dryer Guide for proper sorting, bading
and control setting information before starting your dryer.
NOTE: Do not overdry. Overdrying can cause shrinkage, static ding, and damage
mrne fabrics. SUGGESTED SUGGESTED
TYPEOFLOAD CYCLE TEMPERATURE
CotIo~ and Ilnanr
Emu HEAw~spreads. lllame6s AUTOMATIC PERMTPRESS
Fads,quilts REGULAR
HEAVY HIGH
HEAVWYEIGHT-Tcwels, jeans, corduroys.
work dotlws
MEDIUMWEIGHTSheets. pillowcases,
coaon underwear. diirs
LIGHTWEIGHT-Batistes, organdies, KNITS GENTLE
lingerie LOW
Permanentpreaq l ynthetks
and blends
HEAVYWEIGHT-Work dolhes, jadwk.
AUTOMATIC
PERM-T PRESS
raincoats PERMANENT HEAVY HIGH
MEDIUMWEIGHTShirk. play dothes. PRESS
sheek. decks
LIGHTWEIGHT-Lingerie, blouses, dresses KNITS GENTLE
LOW
Knits
HEAVYWEIGHT-Cottons, rayons, blends,
T-shirts, slacks, shirts
MEDIUMWEIGHT4ynthet (polyester,
aayiic, eta.). dress slacks, &irk, sweaters
LlGHlWEIGHT4ynthetics (polyester,
aayiic. etc.) and blends, lingerie, Mouses,
dl8SSeS
AUTOWTIC
PERMANENT
PRESS
PERM’T PRESS
HEAVY HIGH
KNITS GENTLE
LOW
Ddkate fob&a AUTOMATIC
Sheercurtains(2or3 peels),
PERMANENT
gauze. lam, etc. PRESS KNITS GENTLE
LOW ,
Rubber, plastk,
hewaensltlve fabrks
FOAM RUBBER-Pillows. bras, stuffed toys
PlASTKXhower curtains. tabledotis
RUBBER-BACKED RUGS
OLEFIN, POLYPROPYLENE,
SHEER NYLON
TIMED DRYING
20-30 min. FLUFF AIR’
20-30 min.
40-N min.
1520 min.
4 ‘See page 7.

1. !Mect a cycle by turning the Cycle
Control Knob either way. Stop
when the indicator on the knob’s
outer ring points to the cycle and
setting you want. See pages 6-7 for
further cycle information.
2. Set the Temperature Selector on
the desired temperature setting.
3. Push the !%rt Button to start the
dryer.
To stop and restart the dryer
l Open the dar or turn the Cycle
Control Knob to OFF to stop the
dryer.
l Cbse the door, select a cycle (if
necessary) and push the Start
Button to restart the dryer.
The Cycle Control Knob should point
to an OFF area when the dryer is not
in use. If the dryer is stopped before
the cycle is finished, turn the Cycle
Control Knob to an OFF area 5

Operating instructions
Continued
Theautomaticcycles
6
The automatic cycles albw you to
select the degree of dryness you
prefer for the clothes being dried.
The automatic DRY-MISEFPcontrol
is a thermostat that senses the dryer
air temperature. The dryer automati-
cally shuts off when the selected
dryness is reached.
The Cycle Control Knob will not
move until the bad is almost dry or the
cooldown portion of the cycle has
been reached. After the oxl-down
portion is complete, the Cycle Control
Knob automatbatty moyes to an OFF
area and tumbling stops.
Use AUTOhMTlC REGULAR to dry
heavy or mediumweight cotton items.
The bad tumbles without heat during
the last 5 minutes. This helps make
the bad easier to handle.
Use ACrrOMATlC PERMANENT
PRESS to dry permanent press, knits
and other synthetic items. The bad
tumbles without heat during the last 10
minutes. This helps keep wrinkles from
setting in and makes the bad easier to
handle.
For the first few loads. set the Cycle
Control Knob to point to the * in either
automatic cycle. When the dryer stops,
feel the dried items.
l If items are drier than you like, use a
setting to the right of the * the next
time you dry a similar bad.
l tf items are not as dry as you like,
use a setting to the left of the Ilr the
next time you dry a similar bad.
NOTE: Overdrying can cause shrink-
age, static cling and damage to some
fabrics.

TIMEDDRYING
Use the TIMED DRYING cycle for any
bad you want to dry by time. This cycle
is designed for small bads, large bulky
items or items to he fluffed or dusted
using the Fluff Air temperature setting.
l Turn the Cycle Control Knob to the
number of minutes you want from 10
to 60.
l For a damp dry, turn the Cyde
Control Knob to 30 minutes or less.
The last 5 minutes of this cyde are
without heat to help make the load
easier to handle.
UsingFLUFFAIR
Fire Hazard
Do not dry plastic or rubber items
wlth heat. Use FLUFF AIR setting,
or line dry. Failure to do so could
result In fire or damaged items.
The dryer does not heat when the
Temperature Selector is set to FLUFF
AIR. This can be used to fluff or air dry
bedding, plastic tabiecbths, foam rubber
pilbws. stuffed toys, sneakers, etc.
1. Turn the Temperature Selector to
FLUFF AIR.
2. Turn the Cyde Control Knob to the
number of minutes you want in the ‘+
TIMED DRYING cycle.
3. Push the Start Button.
NOTE: Repeat steps above if more
time is needed to dry items.

CaringForYourDryer
Product and Fabric Damage Hazard
Do not run the dryer wtth the lint scrB8n kose,
damaged, blocked or mlsslng. Dolng so can
cau~ overheatlng and damage to both the
dryer and fabrics.
Cleaningthelint screen
The lint screen is located under a lid
on top of the dryer. Clean it More
each load. A screen bbcked by lint
can increase drying time.
1. Cpen the lii and pull the lint screen
straight out
2 Roll lint off the screen with your
fingers. Do not rinse or wash the
screen to remove lint Wet lint is
hard to remove.
3. Push the lint screen firmly back into
place and close the iii.
Lint screenmaintenance
Laundry detergents and fabric
softeners can cause a residue build-up
on the lint screen. A clogged lint
screen can extend drying times. Clean
the lint screen every six months or
more frequently if it becomes clogged
due to a residue build-up. Use the
folbwing method:
1. Wet both sides of lint screen withk
hot water.
2 Wet a nybn brush with hot water
and liquid detergent
3. Scrub lint screen with the brush
until all residue build-up is re-
moved.
4. Rinse with hot water.
5. Thoroughly dry lint screen with a
clean towel and replace in dryer.

Gleaningmearyer
ElectrIcal Shock and
Personal Injury Hazard
l Turn off the electrical power
before cleaning the Interbr.
l Make sure the dryer Is cool.
Failure to do so could result In
elect&al shock or Injury.
Fire Hazard
l Use non-flammable cleaner.
Failure to do so could result In an
expbsbn.
Garments which contain unstable dyes,
such as denim blue jeans or brightly
colored cotton items, may discolor the
dryer interior.
If you want to remove stains from
dryer drum use one of the folbwlng
methods:
Powdered Laundry detergent
1. Make a paste with detergent and
very warm water.
2. Apply paste to a soft cloth and scrub
area until all excess dye is removed.
3. wipe thoroughly with a damp cloth.
4. Tumble a bad of rags to dry.
Llquld non-flammable household
cleaner
1. Apply to stained area
2. Rub with a cloth until all excess dye
is removed.
3. Wipe thoroughly with a damp cloth.
4. Tumble a bad of rags to dry.
To clean dryer exterior:
Wipe with a soft, damp doth.
9

Caring For Your Dryer
Contlnued
Lint removal
Lint can gather inside the dryer and be
a fuel for fire, It is recommended the
lint be removed every 2 to 3 years, or
more often, depending on dryer
usage. Cleaning should be done by a
qualified person. lf you have any
questions, please call our Consumer
Assistance Center at 1-800-253-l 301.
Ebotrk dya with back panel ranoved
lanker 1
Gas dryer with bwer front
10
access panel removed
ElectrIcal Shodc and
Personal Injury Hazard
l Unplug the power supply cord
or turn off the elect&al power
before removing dryer panels.
l Make sure the dryer Is cool.
l Dryer parta can have sharp
edgea Use care when han-
dllng.
l When replacing front panel
after lint removal, the wlre cllps
holding the door awftch wlree
must be anchored to top of
front and skle panels. Wires
MUST NOT touch rotating
drum. (See page 11, step 7.)
Failure to do eo could result in
elect&al shock or personal
Injury.
fyour dryer Is electrk, or la gas
and has a lower front access panel:
1. Unplug the power supply cord or .
turn off the elecirical power.
2 Remove back panel (electric) dr
bwer front access panel (gas). See
Installation Instructions.
3. Remove lint from shaded area in
illustration with a soft brush or
vacuum deaner. Avoid damaging
wires, thermostats (electric), funnel
(gas) or igniter (gas).
4. Replace panel; reconnect and
level dryer again, if necessary.
NOTE: See page 11 if your dver is
gas and has a full front panel.