Whirlpool LE5800XS User manual

J
AUTOMATIC
DRYERS
Electric Model
LE5800XS
and
Gas Model
LG58olXS
Microwave Ovens. Trash Compactors. Room Air Condltloners. Oehumldlfws. Automatic Washers. Clothes Dryers. Freezers. Aelrlgerator-f

Parts and features
CYCLE CONTROL KNOB
LAUNDRY INK)RMATION CENTER
START BUlTON
DRYERDRUM
MODEL
AND SERIAL
NUMBER PLATE
LOADING DOOR
Remove the Con-
sumer Buy Guide label
before using your
dryer. It will be easier
to remove.
Wipe out the dryer
drum with a damp
cloth to remove dust
from storing or ship-
ping.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this information ready:
1. Complete Model and Serial Numbers
(from the plate located as shown).
2. Purchase date from sales slip.
Copy this information in these spaces.
KeeD this book in the Laundrv Information
Cen’ter with your “Dryer Guide:’ sales slip
and warranty.
Model Number
Serial Number
Purchase Date
Please complete and mail the Owner
Registration Card furnished with this
product. Service Company
Telephone Number
Contents
Page Page
PARTS AND FEATURES ......... 2
Drying Times ................ 8
IMPORTANT SAFETY
Mixed Loads ................ B
INSTRUCTIONS. ............... 3 End-of-Cycle Signal ......... B
OPERATING INSTRUCTIONS. ... 4
Lint Signal .................. B
Selecting a Cycle and LINT SCREEN .................. 9
Starting Your Dryer ........ 4 LINT REMOVAL ................. 9
Automatic Cycles. .......... 6 CARING FOR YOUR DRYER ..... 10
Timed Drying ............... 6 Cleaning Dryer Interior ...... 10
DRYING TIPS .................. 7
Vacation Care .............. 10
FLUFFAIR Setting ............ 7 IF YOU NEED SERVICE OR
TUMBLEPRESS@Setting .......
7 ASSISTANCE .................. 11
Automatic DRY-MISERa WHIRLPOOL DRYER
Control ................... 7 WARRANTY ................... 12
Gentle Heat. ................ 7
2 01987 Whirlpool Corporation

I IIi
ALWAYS shut off the gas valve before ALWAYS Unplug the power supply cord
leaving on vacation. or
turn off electrical power before at-
NEVER use or store flammable fluids tempting to service the dryer. Shut off
(dry-cleaning solvents, gasoline, ker- GAS VALVE if yours is a gas dryer.
osene) in or near your dryer. These sub- You are personally responslble for
stances give off vapors that can create maklng sure that your dryer...
a FIRE HAZARD or EXPLOSION.
l is properly maintained.
NEVER operate the dryer if... . is
Properly installed and leveled in a
l it is not working right [i.e. noisy, too hot). Well ventilated room* on a floor that
l it is damaged. can support the weight.
l parts are missing [i.e. door latch]. . is located in an area where the tem-
l all panels are not in place. perature is above 45°F (7.2%).
l the lint screen is loose, damaged or
l is connected to the proper outlet and
missing. electrical supply.*
l is properly connected to fuel and ex-
l FOR YOUR SAFETY l
haust systems.*
IF YOU SMELL GAS:
l is not installed against drapes or
1. OPEN WINDOWS. curtains.’
2. DON’T TOUCH ELECTRICAL SWITCHES.
l is used only for jobs normally ex-
3. EXTINGUISH ANY OPEN FLAME. petted of home clothes dryers.
4. IMMEDIATELY CALL YOUR GAS . is not used by children or anyone un-
SUPPLIER. able to operate it properly.
‘See “lnstallatlon InstructIons” tor
complete lntormatlon.

Selecting a
and Starting
Your Dryer
Before starting your dryer, be
sure laundry is sorted and loaded
properly (see your “Dryer Guide”).
Be sure the door Is tightly closed.
SUGGESTED SUGGESTED
TYPE OF LOAD CYCLE TEMPERATURE
COlTONS - LINENS
EXTRAHEAW - Bedspreads,
mattress pads, quilts . HEAVY
HEAVYWEIGHT FABRICS-Towels,
HIGH
jeans, corduroys, work clothes .
MEDIUMWEIGHT COTTONS -
Sheets, pillowcases, cotton
AUTOMATIC PERM’T PRESS
REGULAR
MED
underwear, diapers . .
LIGHTWEIGHT COTTONS- Batistes,
organdies, lingerie .
PERMANENT PRESS, SYNTHETICS
AND BLENDS
KNITS GENTLE
LOW
HEAVYWEIGHT FABRICS-Work clothes,
jackets, raincoats . .
MEDIUMWEIGHT FABRICS-Shirts, play
clothes, sheets, slacks.
LIGHTWEIGHT FABRICS - Lingerie,
blouses,dresses.......................
KNITS
HEAVYWEIGHT - Cottons, rayons,
blend&T-shirts, slacks, shirts .
LIGHTWEIGHT - Synthetics (polyester,
acrylic, etc.) and blends, lingerie,
blouses, dresses . .
LIGHTWEIGHT AND DELICATE FABRICS
Sheer Curtains (2 or 3 panels]
Gauze, lace, etc. . . . .
RUBBER, PLASTIC, HEAT-SENSITIVE
FABRICS
FOAM RUBBER - Pillows, bras,
stuffedtoys............................
PLASTIC-Shower curtains,
tablecloths . . . . . . .
RUBBER-BACKED RUGS .
OLEFIN, POLYPROPYLENE, SHEERNYLON
AUTOMATIC PERMIT PRESS
PERMANENT MED
PRESS MED LOW
AUTOMATIC
MED LOW
PERgF;NT KNITS GENTLE
LOW
AUTOMATIC
PERMANENT Ex LOW
PRESS
FLUFF Ex LOW
AIR
4

I
n Select a CYCLE 2
Set
n TEMPERATURESELECTOR
Turn the Control Knob either way to
point to the cycle and setting you
want. See page 6 for information on
the cycles.
3
n Push the STARTButton
The Temoerature Selector can be set 1
on any besired temperature or any-
where between 2 temperatures.
To stop and restart
the dryer
The dryer will start tumbling when you
push the STARTButton.
Ifthe STARTButton is pushed when the
Cycle Control Knob is pointing to an
OFF area, the End-of-Cycle Signal will
sound. Dryer will not start.
To stop the dryer, open the door (or
turn the Control Knob to OFF).
To restart the dryer, close the door,
select cycle, if necessary, and push
START.
The Cycle Control Knob
If the dryer is stopped bet
Knob to OFF.
should point
ore the cycle ‘to OFF when the dryer is not in use.
!is finished, turn the Cycle Control

The automatic cycles
The automatic cycles allow you to se-
lect the degree of dryness you prefer
for the clothes being dried.
The Control Knob will not move until
the clothes load is almost dry, or the
CCCL-DOWN portion of the cycle has
been reached. After CCCL-DOWN, the
knob automatically moves to an OFF
area and tumbling stops.
weight cotton items. The load tumbles
without heat durlng the last 5 mln-
utes. This helps make the load easier
to handle.
press, knits and other synthetic fab-
rics. The load tumbles wlthout heat
durlng the last 10 mlnutes. This helps
keep wrinkles from setting in, and
makes the load easier to handle.
Forthe first few loads, set the Control
Knob to point to an $+ in either auto-
matic cycle. When the dryer stops, feel
the dried items.
l If items are drier than you like, use
a setting to the right of the Jk the next
time YOU
drv a similar load.
l If items are not as dry as you like, use
a setting to the left of the +$the next
time you dry a similar load.
Timed drying
Usethe TIMEDDRYING Cycle for
any load you want to dry by time. For
example: small loads, large bulky
items, items to be fluffed or dusted
with the FLUFFAIR heat setting.
l Turnthe Control Knob to the number
of minutes you want-from 10to 70.
l The last 5 minutes of this cycle are
without heat - a cool-down time. This
helps make the load easier to
handle.
6

Drying tips
TUMBLE PRESS” Setting
The TUMBLEPRESSsetting removes
The dryer does not heat when the
Control Knob is set on FLUFFAIR.This
setting can be used to fluff bedding,
wrinkles from dry clothing such as
items that may have been packed
in a suitcase, closet, or items not
removed from the dryer.
plastic tablecloths, foam rubber
pillows, stuffed toys, sneakers, etc.
1. Set Control Knob to TUMBLEPRESS.
2. Set Temperature Selector to PERM’T
1. Turn the Control Knob to the number PRESS/MED.
of minutes you want in FLUFFAIR. 3. Push STARTButton.
2. Push the STARTButton. The load will tumble in heated air
for15
Iminutes. The heat shuts off and
the dryer continues to tumble the load
for 5 more minutes.
For best results, TUMBLEPRESSonly
a few items at a time. Putthem on
hangers or fold them as soon as the
A-~-- -I---
aryer slops.
Automatic DRY-MISER” Gentle Heat
Control
The dryer automatically reduces
The thermostat senses the air the heatsettings in HEAW.HIGH and
temperature. The dryer automatically PERM’TPRESSMED cyc’es.During
shuts off when the selected dryness the last few minutes of each of
is reached. these cycles the dryer temperature
gradually reduces to a lower heat
setting. This helps prevent
overdrying.

I
III
Drying times Mixed loads
Drying times will vary depending on:
l amount of moisture in the clothes.
l type and weight of the fabric.
l size of the load.
When drying a load with different
kinds and weights of fabrics, use the
cycle suggested for the lightest fab-
rics. When the dryer stops, remove dry
items and reset the control.
l room temperature around the dryer.
l temperature of the wash rinse water.
0 amount of lint in the lint screen.
l dryer temperature selection.
See your “Dryer Guide” for
more information.
Toreduce wrinkling, take the load
from dryer as soon as tumbling stops.
This is important for permanent press,
knits and synthetic fabrics.
End-of-cycle signal
The dryer sounds a signal to let you know when
the cycle is finished. The signal cannot be turned
off and is not adjustable.
The signal is helpful when you are drying per-
manent press, synthetics and other items that
should be taken out as soon as the dryer stops.
dd
e
Lint signal
Clean lint screen before each load. If you
neglect to clean your lint screen, the signal will
sound. The (whistle tone) signal lets you know
the air How is being restricted. Restricted air flow
reduces drying efficiency.
Turn off the dryer and clean the lint screen as
w shown on page 9.
8

Lint screen
Clean the lint screen before each load. A screen blocked by lint can
increase drying time und may be a FIREHAZARD.
Open the lid and pull the lint screen
straight out.
ROLL the lint off the screen with
your fingers.
DO NOT rinse or wash the screen.
Push the screen firmly back into place
Lint removal
Lint can gather inside the dryer and create a FIRE HAZARD. This lint should
be removed at least every 2 to 3 years, or more often, depending on
dryer usage.
ELECTRIC DRYERS GAS DRYERS
Cleaning should be done only by a qualified person.
WARNING:
0
l Avoid electrical shock
hazard ‘- unplug power
supply cord or turn off
electrlcal power.
l Avold Injury or damage-do not
put hands inside cabinet.
l Make sure dryer is cool.
1. Remove back panel (electric]
or lower access panel [gas].
2. Avoid damaging wires,
thermostats, funnel or igniter.
3. Remove lint from shaded area -
see art - with a soft brush or
vacuum cleaner.
4. Replace panel; reconnect and
re-level dryer.
9

r
Remove loose and sharp objects
from pockets and cuffs before drying -
pins, buckles, etc. Close metal
zippers.
Wlpe off all spills with a damp, sofi
cloth. Spills allowed to remain may
dull or damage the finish.
Never leave wet or damp laundry
in your dryer.
Sharp or heavy objects should
never be put on or in the dryer.
Check pockets for bolts, nuts etc.
10
Some pretreatment products can
damage dials, consoles and finish.
Do not use these products on or near
your dryer.
Cleaning dryer interior
0
WARNING: Before
cleaning Interior, unplug
power supply cord or,
turn otl electrical power to
avold electrical shock hazard.
Garments which contain unstable
dyes, such as denim blue jeans or
brightly colored cotton items, may
discolor the dryer interior. Ifthe
interior is discolored, clean with
one of the following methods to
avoid staining later load items.
Powdered laundry detergent and
very warm water
Make a paste with detergent and
very warm water. Apply paste to
a soft cloth and scrub area until
all excess dye is removed. Wipe
thoroughly with a damp cloth.
Tumble a load of rags. -OR-
Liquid spray household cleaner
Spray on stained area. Rub with
a cloth until all excess dye is
removed. Tumble a load of rags.
Vacation care
l Unplug power cord or turn off
electrical power.
l For gas dryers, close gas valve.
l Clean lint screen.

If you need service or assistance,
we suggest you follow these five steps:
L Before calling for
assistance...
Performance problems often result
from little things you can find and fix your-
self wlthout tools of any kind.
IF YOUR DRYER DOES NOT RUN:
l Is the power supply plugged into a live
circutt with the proper voltage?
l Is the door closed tightly?
l Did you push the START Button?
l Have you checked your home’s main
fuses or circuit breaker box?
IF YOUR DRYER DOES NOT HEAT:
l The AIR setting is without heat.
l The last minutes of heat settings are with-
out heat.
l Is the gas turned on? If not, turn the COn-
trol Knob to OFF. Turn on gas. Wait 5 min-
utes. Reset controls and start.
l An electric dryer uses a circuit breaker
or 2 fuses. If one fuse is blown, the dryer
may run, but not heat.
IF DRYING TIME SEEMS TOO LONG:
l Is the lint screen clean? See page 9 of
this book for cleaning instructions.
l See page 8 of this book and your”Dryer
Guide:’
2. If you need
assistance?..
Call Whirlpool COOL-LINEB rervlce as-
slstance telephone number. Dlal tree
tram anywhere In the U.S.:
I-800-253-1301
and talk with one of our trained Consul-
tants. The Consultant can instruct you in
how to obtain satisfactory operation from
your appliance or, if service is necessary,
recommend a qualified service com-
pany in your area.
3. If you need service?..
Whirlpool has a
.I
r”““’ 2
nationwide net-
work of franchised
TECU-CARE
TECH-CARE@ Serv-
FMNC”,SEDSERVICE ice Companies.
TECH-CARE service
technicians are trained to fulfill the prod-
uct warranty and provide after-warranty
service, anywhere in the United States. To
locate TECH-CARE service in your area,
call our COOL-LINE service assistance
telephone number (see Step 2) or look in
your telephone directory Yellow Pages
under:
Call our COOL-LINE service assistance
telephone number (see Step 2) and talk
with one of our Consultants, or if you pre-
fer, write to:
Mr. Robert Stanley
Division Vice President
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
5. If you need FSP@
replacement parts?.
FSP is a registered trademark of
Whirlpool Corporation for quality parts.
Look for this symbol of quality whenever
you need a replacement part for your
Whirlpool appliance. FSP replacement
parts will fit right and work right, because
they are made to the same exacting
specifications used to build every new
Whirlpool appliance.
*If you must call or write, please provide:
model number, serial number, date of
purchase, and a complete description
of the problem. This information is
needed in order to better respond to
your request for assistance.
11

WHIRLPOOL” DRYEtR
WARRANTY
LENGTH OF WARRANlY 1 WHIRLPOOL WIU PAY FOR I
FULL ONE-YEAR
WARRANlY
From Date of Purchase
FSPa replacement parts and repalr labor to
correct defects in materials or workmanship.
Service must be provlded by a franchised
TECH-CARE@ service company. I
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
I. Correct the installation of the dryer.
2. Instruct you how to use the dryer.
3. Replace house fuses or correct house wiring or plumbing.
4. Replace light bulbs.
B. Repalrs when dryer is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in
the home.
D. Damage to dryer caused by accident, misuse, fire, flood, dcts
of God or use of oroducts not aooroved bv Whlrlaool.
WHIRLPOOL CORPORATION SHALL NOT BELIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of
Incidental or consequential damages so this llmitatlon or exclusion may
not apply to you. Thls warranty gives you specific legal rights, and you may
also have other rights which vary from state to State.
Outside the United States, a different warranty may apply. For details, please
contact your franchised Whirlpool distributor or military exchange.
Part No. 3388803
01987 Whirbool CorDoration Printed in U.S.A.
Automatic Washers. Clothes Dryers, Freezers. Refrlgerafor-Freezers. Ice Makers, DIshwashers. Built-In Ovens and Surface Units. Ranges,