Whirlpool LE681OXP User manual

i-
/
AUTOMATIC
DRYERS
Electric Model
LE681OXP
and
Gas Model
LG6811XP
* -;..+rP-r .‘!-i~;l~~.cL.*i 7r -P,i .,.s.ar,i -wb. -T. I ..I,.7 =,.?+,<” i. ; ;:@tr -;
wave Ovens, Trash Compactors, Room Air Condltloners. Oehumldlflers. Automatic Washers, Clothes Dryers, Freezers, Refrigerator-Freeze1

Parts and features
CYCLE CONTROL LAUNDRY
KNOB INFORMATION CENTER
\ TEMPERATURE SELECTOR
START BUTTON
NUMBER PLATE
LOADING DOOR
Remove the Con-
sumer Buy Guide la-
bel before using
your dryer. It will be
easier to remove.
Wipe out the
dryer drum with a
damp cloth to re-
move dust from stor-
ing or shipping.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this informatlon ready Complete Model Number
1. Comdete Model and Serial Numbers
(from-the plate located as shown)
2. Purchase date from sales slip.
Complete Serla Number
Copy this InformatIon in these spaces
Keep this book, your warranty, sales slip
Purchase Date
and “Dryer Guide” In the Laundry Infor-
mation Center on the back of the dryer
Service Company and
console
Telephone Number
Contents
Page
PARTS AND FEATURES
YOUR RESPONSIBILITIES
SAFETY FIRST
SELECTING A CYCLE AND
STARTING YOUR DRYER
OPERATING INSTRUCTIONS
The Automatic Cycles.
Timed Drying
DRYING TIPS.
FLUFFAIR Setting
TUMBLE PRESS” Setting
Gentle Heat
Drying Times
Mixed Loads.
2
3
3
End-of-Cycle Signal.
Lint Signal
LINT SCREEN
LINT REMOVAL
CARING FOR YOUR DRYER
Cleaning Dryer Interior..
Vacation Care.
IF YOU NEED SERVICE OR
ASSISTANCE.
I. Before Calling for
Assistance
2. If You Need Assistance
3. If You Need Service
4. If You Have a Problem
11
11
11
11
11
2 ~1985 Whirlpool Corporation

Your
Responsibilities
l is located in an area where the tem-
Read this “Use and Care Guide” perature is above 45’F (7.2 C).
and your “Dryer Guide” carefully for l is connected to the right kind of out-
important use and safety information. let, electric supply and grounding.’
You are personally responsible for
l is properly connected to fuel and
making sure that your dryer... exhaust systems.’
l is used only for jobs normally ex-
l is installed by a qualified installer. petted of home clothes dryers.
l is properly maintained.
l is not run where there may be explo-
l is installed in an area protected sive fumes.
from the weather.
l is not used by children or anyone
l is properly installed and leveled in unable to operate it properly.
a well ventilated room’ on a floor *See the “Installation Instructions” for
that can support the weight. complete information.

Selecting a cycle
and starting
your dryer
Before starting your dryer, be
sure laundry is sorted and loaded
properly (see your”Dryer Guide”).
Be sure the door is tightly closed.
TYPE OF LOAD
COTTONS - LINENS
EXTRA HEAVY - Bedspreads,
mattress padsquilts.
HEAVYWEIGHT FABRICS -Towels,
jeanscorduroys, work clothes
MEDIUMWEIGHT COTTONS -
Sheets, pillowcases, cotton
underwear,diapers
LIGHTWEIGHT COTTONS - Batistes.
organdies, lingerie
SUGGESTED SUGGESTED
CYCLE TEMPERATURE
HEAVY
HIGH
AUTOMATIC
REGULAR PERMIT PRESS
MED
KNITS GENTLE
LOW
PERMANENT PRESS, SYNTHETICS
AND BLENDS
HEAVYWEIGHT FABRICS -Work clothes,
jackets, raincoats AUToMATlC PERM’T PRESS
MEDIUMWEIGHT FABRICS - Shirts, play PERMANENT
PRESS MED
clothes,sheets,slacks
LIGHTWEIGHT FABRICS - Lingerie,
blousesdresses MED LOW
KNITS
HEAVYWEIGHT - Cottons, rayons,
blends,T-shirts, slacks, shirts AUTOMATIC MED LOW
LIGHTWEIGHT-Synthetics [polyester, PERMANENT
acrylic, etc.) and blends, lingerie, PRESS KNITS GENTLE
blouses, dresses LOW
LIGHTWEIGHT AND DELICATE FABRICS AUTOMATIC
Sheer Curtains (2 or 3 panels) PERMANENT
Gauze, lace,etc. PRESS Ex LOW
RUBBER, PLASTIC, HEAT-SENSITIVE
FABRICS
FOAM RUBBER - Pillows, bras,
stuffed toys
PLASTIC - Shower curtains,
tablecloths . . . .._...............
RUBBER-BACKED RUGS
OLEFIN, POLYPROPYLENE, SHEER NYLON
PERMIT PRESS
20-30 MINS. FLUFF
AIR
20-30 MINS.
40-50 MINS.
15-20 MINS.

Select a
1. CYCLE Set TEMPERATURE
2. SELECTOR
Turn the Control Knob either way to
point to the cycle and setting you
want. See page 6 for information on
the cycles.
Push the
3. START Button
The dryer will start tumbling when
you push the START Button.
The Cy rcle Control Knob should point to OFF when the dryer is not in use.
The Temperature Selector can be set
on any desired temperature or any-
where between 2 temperatures.
To stop and restart
the dryer
To stop the dryer, open the door (or
turn the Control Knob to OFF).
To restart the dryer, close the door,
select cycle, if necessary, and push
START.

Operating instructions
The automatic cycles
The automatic cycles allow you
to select the degree of dryness you
prefer for the clothes being dried.
The Control Knob moves and stops
several times until the load reaches
the dryness setting You selected. Then
the knob automatically moves to
OFF and tumbling stops.
weight cotton items. The load tum-
bles without heat during the last 5
minutes. This helps make the load
easier to handle.
Use
AUTOMATIC
PERMANENT
PRESS to dry
P.lr.VV-%~P.r\,-.l
press, knits and other synthetic fab-
rics. The load tumbles without heat
during the last 40 minutes.This helps
keep wrinkles from setting in.
For the first few loads, set the Control
Knob to point to an* in either auto-
matic cycle. When the dryer stops,
feel the dried items.
l If items are drier than you like, use
a setting to the right of the* the next
time you dry a similar load.
l If items are not as dry as you like,
use a setting to the left of the * the
next time You dry a similar load.
Timed drying
Use the TIMED DRYING Cycle for
any load you want to dry by time. For
example: small loads, large bulky
items, items to be fluffed or dusted
with the FLUFFAIR heat setting.
l Turn the Control Knob to the number
of minutes you want - from 10 to 70.
l The last 10 minutes of this cycle are
without heat - a cool-down time. This
helps make the load easier to
handle.
6

Drying tips
FLUFF AIR
The dryer does not heat when the
Control Knob is set on FLUFFAIR. This
setting can be used to fluff bedding,
plastic tablecloths, foam rubber pil-
lows, stuffed toys, sneakers, etc.
1. Turn the Control Knob to the number
of minutes you want in FLUFFAIR.
2. Push the STARTButton.
TUMBLE PRESS” Setting
The TUMBLE PRESS setting removes
wrinkles from dry clothing such as
items that may have been packed
in a suitcase, closet, or items not
removed from the dryer.
1. Set Control Knob to TUMBLE PRESS.
2. Set Temperature Selector to PERM’T
PRESS/ MED.
3. Push START Button.
The load will tumble in heated air
for 10 minutes. The heat shuts off and
the dryer continues to tumble the
load for 10 more minutes.
For best results.TUMBLE PRESS only
a few Items at a time. Put them on
hangers or fold them as soon OSthe
dryer stops.
Gentle Heat
The dryer automatically reduces the
heat setting rn HEAVY HIGH and PERM’T
PRESSMED cycles. The last 7 minutes
of each of these cycles gradually
reduces the dryer temperature to a
lower heat setting. Thls helps prevent
over drying.
7

Drying tips
Drying times Mixed loads
Drying times will vary depending on:
l amount of moisture in the clothes.
l type and weight of the fabric.
l size of the load.
l room temperature around the
dryer.
When drying a load with different
ktnds and weights of fabrics, use the
cycle suggested for the lightest fab-
rics When the dryer stops, remove
dry items and reset the control.
l temperature of the wash rinse
water.
l amount of lint in the lint screen.
l dryer temperature selection.
See page 6 in your “Dryer Guide”
for more information.
End-of-cycle signal
The dryer sounds a signal to let you know
when the cycle is finished. The signal cannot be
turned off and is not adjustable.
The signal is helpful when you are drying
permanent press, synthetics and other items
that should be taken out as soon as the dryer
stops.
Lint signal
Clean lint screen before each load. If you
neglect to clean your lint screen, the signal will
sound. The (whistle tone) signal lets you know
the air flow is being restricted. Restricted air flow
reduces drying efficiency.
Turn off the dryer and clean the lint screen us
shown on page 9.
8

Lint screen
Clean the lint screen before each 1oad.A screen blocked by lint can
increase drying time and may be a FIRE HAZARD.
Open the lid and pull the lint screen
straight out. ROLL the lint off the screen
wrth your fingers.
DO NOT rinse or wash the screen.
Push the screen firmly back into
place.
Lint removal
Lint cun gather inside the dryer and create a fire hazard.This lint
should be removed every 2 to 3 years, or more often, depending on
dryer usage.
ELECTRIC DRYERS GAS DRYERS
Cleaning should be done only by a qualified person.
0
WARNING:
l Avoid electrical shock
hazard - unplug power
supply cord or turn off
electrical power.
l Avoid injury or damage-do not
put hands inside cabinet.
. Make sure dryer is cool.
1. Remove back panel (electric)
or lower access panel (gas].
2. Avoid damaging WireS,
thermostats, funnel or igniter.
3. Remove lint from shaded area -
see art - with a soft brush or
vacuum cleaner.
4. Replace panel; reconnect and
re-level dryer.
9

Caring for your dryer
Remove loose and sharp objects
from pockets and cuffs before dryina - Some pretreatment products can
damage dials, consoles and finish.
pins, buckles, etc. Close metal -
zippers. Do not use these products on or
near your dryer.
Wipe off all spills with a damp, soft
cloth. Spills allowed to remain may
dull or damage the finish.
Never leave wet or damp laundry
in your dryer.
Sharp or heavy objects should
never be put on or in the dryer,
Check pockets for bolts, nuts, etc.
10
Cleaning dryer interior
0
WARNING: Before
cleaning interior, unplug
power supply cord, or
turn off electrical power to
avoid electrical shock hazard.
Garments which contain unstable dyes,
such as denim blue jeans or bright-
ly colored cotton items, may discolor
the dryer interior. If the interior
is discolored, clean with one of the
following methods to avoid staining
later load items.
Powdered laundry detergent and
very warm water
Make a paste with detergent and
very warm water. Apply paste to
a soft cloth and scrub area until all
excess dye is removed. Wipe thor-
oughly with a damp cloth. Tumble
a load of rags. -OR-
liquid spray household cleaner
Spray on stained area. Rub with a
cloth until all excess dye is re-
moved. Tumble a load of rags.
Vacation care
l Unplug power cord or turn off elec-
trical power.
l For gas dryers, close gas valve.
l Clean lint screen.

If you need service or assistance, we suggest
you follow these four steps:
1. Before calling for
assistance...
Performance problems often result
from little things you can find and fix
yourself without tools of any kind.
If your dryer does not run:
l Is the power supply cord plugged
into a live circuit with the proper volt-
age?
l Is the door closed tightly?
l Did you push the STARTButton?
l Have you checked your home’s
main fuses or circuit breaker box?
If your dryer does not heat:
l The AIR setting is without heat.
l The last minutes of heat settings are
without heat.
l Is the gas turned on? If not, turn the
Control Knob to OFF. Turn on gas.
Wait 5 minutes. Reset controls and
start.
l An electric dryer uses a circuit
breaker or 2 fuses. If one fuse is
blown, the dryer may run, but not
heat.
If drying time seems long:
l Is the lint screen clean?
l See page 7 of this book and page 6
of your “Dryer Guide:’
2. If you need
assistance*...
Call Whirlpool COOL-LINE” serv-
ice assistance telephone number.
Dial free from:
Continental U.S. . [phone]
Michigan . . . . . . . . [phone]
Alaska & Hawaii [phone]
and talk with one of our trained Con-
sultants. The Consultant can instruct
you in how to obtain satisfactory oper-
ation from your appliance or, if serv-
ice is necessary, recommend a
qualified service company in your
area.
3. If you need service*...
Whirlpool has
nationwide
network of fran-
chised TECH-CARE”
Service Compa-
TECH-CARE
service technicians are trained to
fulfill the product warranty and pro-
vide after-warranty service, any-
where in the United States. To locate
TECH-CARE service in your area, Call
our COOL-LINE service assistance
telephone number (see Step 2) or look
in your telephone directory Yellow
Pages under:
4. If you have a
problem*...
Call our COOL-LINE service as-
sistance telephone number [see Step
2) and talk with one of our Consultants,
or if you prefer, write to:
Mr. Robert Stanley
Division Vice President
Whirlpool Corporation
2000 US-33, North
Benton Harbor, Ml 49022
*If you must call or write, please pro-
vide: model number, serial number,
date of purchase, and a complete
description of the problem. This infor-
mation is needed in orderto better re-
spond to your request for assistance.
11

Whirlpool
Home A /Appliances
Making your world a little easier
Part No. 696760
01985 Whirlpool Corporation Printed in U.S.A.
matlc Washers, Clothes Dryers, Freezers. Refr~geralor-Freezers. Ice Makers. DIshwashers. Bult-In Ovens and Surface Un~ls. Ranges, M~crr