Whirlpool LE9100XT User manual

Use&CareGuide
Cycle control knob
I Temperature selector
Start button
Unt screen
Drying rack (not shown)
models E92OOXW LG9201 XW
IARGECAPACITYAUTOMATKDRYERS
LE9100XT LG91OlX-TLE9200XWLG92OlXW

Contents
Page
Important Safety lnstructlons.. ...... .3
Additional safety instructions and
your responsibilities ...................... .3
Cparatlng InstructIons
Starting your dryer. ......................... 4
The automatic cycles .................... .6
TIMED DRYING ............................ .7
The FLUFF AIR cyde ..................... 7
Addltlonal Dryer Features
Gentle Heat system ...................... .8
FINISH GUAROO setting ................ 8
Endof-cycle signal ........................ .8
Using the drying rack .................... .9
Caring For Your Dryer
Cleaning the lint screen ................ 10
Lint screen maintenance .............. 10
Cleaning the dryer.. ..................... .11
Lint removal ................................. 12
lfYouNeedservlceor
Asslstatlce ...................................... 13
Whlrlpool Automatic Dryer
Warranty ......................................... 16
631992 Whirlpool Corporation
The drawings in this book may vary
slightly from your dryer model. They are
designed to show the different features
of the models revered by this book.
NOTE: Your modal may not include all
the features shown.
lf your dryer has a Consumer Buy Guide
label, remove it tt will be easier to
remove before the dryer is used. To
remove any remaining glue:
l Rub briskly with thumb to make a ball,
then remove.
or
l Soak area with liquid hand dish-
washing detergent before removing
glue as describsd above.
Do not use sharp instruments, rubbing
alcohol, flammable fluids or abrasive
cleaners. These can damage the finish.
See ‘Important Safety Instructions’ on
page 3.
NOTE: Do not remove any permanent
instrudion labels inside the dryer.
2
You should wipe out the dryer drum
with a damp doth before using to
remove dust from storing or shipping.
Thank you for buying a Whirlpool
appliance. Please complete and mail
the Owner Registration Card provided
with this product. Then complete the
form below. Have this information
ready if you need service or call with a
question.
l Copy model and serial numbers from
plate (on the frame behind the door)
and purchase date from sales slip.
l Keep this book, the Dryer Guide and
the sales slip together in a handy
place.
Model Number
Sadal Number
Rmhaae Date
!SedoeCompnny Phone Number
FOR YOUR SAFETY
If you smell gas:
1. Open wlndows.
2. Don’t touch electrlcal
switches.
3. fiFiegulsh any open
.
4. lmmedlately call your
gas suppller.
FOR YOUR SAFETY
Do not store or use
gasollne or other
flammable vapors and
llqulds In the vlclnlty of
thls or any other appliance.
The fumes can create a fire
hazard or exploslon.

ImportantSafetyInstructions
To reduce the rlsk of fire, electrlcal shock, or
Injury to persons when uslng your dryer, follow
bask precautions, lncludlng the followlng:
l Read all lnstructlons before uslng
l You are responsible for maklng
the dryer. sure that your dryer is installed,
l NEVER dry items cleaned, washed, repaired and has parts replaced by a
soaked in or spotted with wax, paint, qualified person.
gasoline or flammable fluids in the
l Use only fabric softeners sp&fcally
dryer. The fumes can create a FIRE labeled as not being harmful to the
HAZARD or EXPLOSION. ALWAYS dryer.
hand launder and air dry fabrics
l FfRE HAZARD and DAMAGE to
containing these materials. materials can resuft from:
l NEVER allow children to operate,
play with or crawl inside the dryer. -drying rubber, rubber-like and heat
sensitive materials with heat.
Close supervision of children is
necessary when the dryer is used -allowing lint build-up inside the
near children. dryer or exhaust system. Cleaning
) DO NOT reach into a dryer if the should be done periodically by a
drum is moving. qualified person.
l Clean lint screen before or after
1When discarding an oki dryer, each bad.
ALWAYS remove the door to
prevent accidental entrapment.
l DO NOT let dust, lint, paper, rags,
1DO NOT install or store dryer where chemicals, etc. pile up around or
it will be exposed to the weather. under the dryer.
1DO NOT tamper with the controls.
l Dryer must be electrically grounded.
See the Installation Instructions.
- SAVE THESE INSTRUCTfONS -
Additional safety instructions and your responsibilities
l NEVER operate the dryer if:
-it is not working right (i.e. noisy,
too hot).
-it is damaged.
-parts are missing (i.e. door latch).
-all panels are not in place.
-the lint screen is loose, damaged
or missing.
l ALWAYS shut off the gas valve
before leaving on vacation if you
have a gas dryer.
l ALWAYS unplug the power supply
cord or turn off electrical power
before attempting to service the
dryer. Shut off GAS VALVE if you
have a gas dryer.
l You are responsible for maklng
sure that your dryer:
-is properly maintained.
-is properly installed and leveled on a
floor that can support the weight in a
well ventilated room:
-is located in an area where the
temperature is above-45°F (7°C).
-is connected to the proper outlet and
electrical supply.’
-is properly connected to fuel and
exhaust systems.*
-is not installed against drapes or
cuff ains.’
-is used only for jobs normally
expected of home clothes dryers.
-is not used by anyone unable to
operate it properly.
*See the Installation Instructions for
complete information.
3

Operatinginstructions
Starting your dryer
Be sure to refer to the chart bebw and the Dryer Guide for proper sorting, bading
and control setting information before starting your dryer.
NOTE: Do not overdry. Overdrying can cause shrinkage, static ding, and damage
some fabrics.
TYPE Of LOAD
cononssnd lhflr
EXTRA HEAW-Badspreads, mattrass
padb, WNs
HEAVYWEIGHT-Towels, jaans, cordumys.
work dothes
MEDIUMWEIGHTSheets, pillowcasas.
cottul undarwear. diapers
LIGHTWEIGHT~tistes, organdies,
lingerie
SUGGESTED
CYCLE
AUTOMATlC
REGULAR
SUGGESTED
TEMPERATURE
HEAW HIGH
HEAW HIGH
PERMT PRESS
KNITS GENTLE
ParmsnenI pm64 syntheIk#
snd bhda
HEAVYWEIGHT-Wok dothas, jackets, AUTOhhTlC PERMT PRESS
mk PERMANENT PRESS
MEDIUMWEIGHTShirk, play dothas. PERMT PRESS
sheees, dada
LIGHTWEIGHT-Lingerie, blouses. drassas KNITS GENTLE
Kdb
HEAWWEIGHTXottcns, rayons, blends, AUTOMATlC PERMT PRESS
T-&ii, slacks. shirk PERMANENT PRESS
MEDlUMWElGHTSynthet (polyester, KNITS GENTLE
aqtic, etc.), dress da&, skirts, sweaters
UGHTWEIGHT-Synthet (polyestar, KNITS GENTLE
acrylic, etc.) and bkds, rlngerie, blouses.
dlt3St3Mi
Ddkate faklcr
Sheer cwkins (2 or 3 panels) AUTOMATlC KNITS GENTLE
gauze, lace, etc. PERMANENT PRESS -
RubN Wtlc,
best-lttve fabrIca
FOAM RUBBERPillows, bras, stuffad toys
rum- curtains. tablecloth6
RUBBER-BACKED RUGS
FLUFF AIR’
20-30 minutes No temperature
20-30 minutes needs to be se-
40250minutes lected. Cycle is
OLEFIN, POLYPROPYLENE,
SHEER NYLON 15-20 minutas unheated.
4 ‘see page 7.

1. Select a cycle by turning the Cycle
Control Knob either way. Stop
when the indicator on the knob’s
outer ring points to the cycle and
setting you want. See pages 6-7 for
further cycle information.
2. Prasa a temperature s&actlon
which matches the type of fabric
being dried. The indicator will
appear over the temperature
selectian you have chosen.
3. Push the Start Button to start
the dryer.
4. To stop and restart the dryer:
l Open the door or turn the Cycle
Control Knob to OFF to stop the
dryer.
l Close the door, select a cycle (if
necessary) and push the Start
Button to restart the dryer.
The Cycle Control Knob should point
to an Off area when the dryer is not
in use. If the dryer is stopped before
the cycle is finished, turn the Cycle
Control Knob to an OFF area
5

Operating lnstructlons
Contlnued
The automatic cycles
The automatic cycles albw you to
select the degree of dryness you
prefer for the cbthes being dried.
The automatic DRY-MISEfVcontrol
is a thermostat that senses the dryer
air temperature. The dryer automati-
cally shuts off when the selected
dryness fs reached. 2
The Cycle Control Knob will not
move until the bad is almost dry or the
cooldown portion of the cycle has
been reached. After the cool-down
portion fs complete, the Cycle Control
Knob automatically moves to an OFF
area and tumbling stops.
Use AUTOMAllC REGULAR to dry
heavy or mediumweight cotton items.
The bad tumbles without heat during
the last 5 minutes. This helps make
the bad easier to handle.
Use AUTOMADC PERMANENT
PRESS to dry permanent press, knlts
and other synthetic items. The bad
tumbles without heat during the last
10 minutes. This helps keep wrinkles
from setting in and makes the bad
easier to handle.
For the first few bads; set the Cycle
Control Knob to point to the + in either
automatic cycle. When the dryer stops,
feel the dried items.
l II items are drier than you like, use a
setting to the right of the *the next
time you dry a similar bad.
l ff items are not as dry as you like,
use a setting to the left of the + the
next time you dry a similar bad.
NOTE: Overdrying can cause shrink-
age, static cling and damage to some
fabrics.
6

number of minutes you want from 10 to
70. The last 5 minutes of this cycle are
without heat to help make the load
easier to handle.
The FLUFFAIR cycle
Fire Hazard
Do not dry plastic or rubber Items
with heat. Use FLUFF AIR cycle,
or line dry. Failure to do so could
result In flre or damaged ttems.
The dryer does not heat when the Cycle
Control Knob is set in FLUFF AIR. This
cyde can be used to fluff or air dry bed-
ding, plastic tablecloths, foam rubber
pillows, stuffed toys, sneakers, etc.
1. Turn the Cycle Control Knob to the
number of minutes you want in
FLUFF AIR.
2. Push the Start Button.
NOTE: Repeat steps above if more
time is needed to dry items.
7

AdditionalDryerFeatures
Gentle tieat system
For better fabric care, the Gentle Heat
system helps prevent overdrying.
Drying temperatures are automatiilly
reduced to a bwer heat setting during
the last few minutes of drying.
Gentle Heat is followed by a cool-
down period in all cydes to make your
clothes easier to handle. 3
FINISHGUARD’setting
3
r,
‘5
/=-
\
\
When you are unable to remove a bad
from the dryer as soon as it stops,
wrinkles ten form. FINISH GUARD
tumbles the bad, without heat, every 5
minutes for up to 40 minutes. This
tumbling rearranges and fluffs the bad
to help avoid wrinkles that set in when
the bad remains in the drum.
You do not have to set the Cycle
Control Knob for FINISH GUARD.
FINISH GUARD takes over automati-
cally to proted the bad if you do not
open the door within 5 minutes after
the PERMANENT PRESS cycle stops.
A signal will sound every 5 minutes
during FINISH GUARD, for up to 40
minutes. The signal will stop when the
dryer door is opened.
End-of-cycle signal
The dryer sounds a signal to let you
know when the cycle is finished. The
signal cannot be turned off and is not
adjustable.
The signal is helpful when you are
drying permanent press, synthetics
and other items that should be taken
out as soon as the dryer stops.

Using the drying rack
(models LE9200XW and LG9201 XW)
The drying rack lets you dry items that
you may not want to tumble. The rack
does not move, but the drum turns.
Make sure nothing hangs over the
edge of the rack.
1. Fit rear legs of the rack into indent-
ations in the back wall of the dryer.
2. Lower the front so the legs rest on
the dryer opening.
3. Put wet items on top of the rack
Leave space between them so air
can reach all surfaces.
4. Close the door and start the dryer.
See below for suggested cycles
and temperature settings when
using the drying rack.
NOTE: The rack must be removed for
normal tumble drying.
Fire Hazard
Drying rubber, plastic and other heat-sensltlve
materials wlth heat can damage them or be a
E HAZARD.
Drying ra& suggestions
Drying time will depend on how much moisture the items hold. The following chart
suggests cycles and temperature settings for the different kinds of items that
might best be rackdried. SUGGESTED SUGGESTED
TO RACK DRY: CYCLE TEMPERATURE
Wool 8weaters TIMED DRYING KNfTS GENTLE
(Bbck to shape and lay flat on the rack)
StUffd toy8 01 p11bW8
(Cotton or polyester fiber filled)
ShrffSd toy8 Or p11kW8
(Foam rubber filled)
Sneak8r8 or canvas shoes
TIMED DRYING
FLUFF AIR
AUTOMATfC
PERM’T PRESS
No temperature
needs to bs
selected. Cycle
is unheated.
9

CaringForYourDryer
Product and Fabric Damage Hazard
Do not run the dryer wlth the llnt screen loose,
damaged, blocked or mlsslng. Dolng so can
cause overheating and damage to both the
dryer and fabrics.
Cleaning the lint screen
The lint screen is located under a lid
on top of the dryer. Clean it before
each load. A screen blocked by lint
can increase drying time.
1. Open the lid and pull the lint screen
straight out.
2. Roll lint off the screen with your
fingers. Do not rinse or wash the
screen to remove lint. Wet lint is
hard to remove.
3. Push the lint screen firmly back into
place and close the lid.
Lint screen maintenance
Laundry detergents and fabric
softeners can cause a residue build-up
on the lint screen. A clogged lint
screen can extend drying times. Clean
the lint screen every six months or
more frequently il it becomes clogged
due to a residue build-up. Use the
following method:
1. Wet both sides of lint screen with
hot water.
2. Wet a nylon brush with hot water
and liquid detergent.
3. Scrub lint screen with the brush
until all residue build-up is re-
moved.
4. Rinse with hot water.
5. Thoroughly dry lint screen with a
clean towel and replace in dryer.
10