Whirlpool WGD8800YC User manual

1
W10392126A
W10392127A-SP
Table of Contents
DRYER SAFETY ............................................................... 2
INSTALLATION REQUIREMENTS................................... 4
Tools and Parts................................................................... 4
LOCATION REQUIREMENTS.................................................... 5
ELECTRIC DRYER POWER HOOKUP-CANADA ONLY .......... 6
Electrical Requirements .................................................... 6
GAS DRYER POWER HOOKUP ................................................ 7
Electrical Requirements .................................................... 7
Gas Supply Requirements................................................. 7
INSTALL LEVELING LEGS......................................................... 8
VENTING..................................................................................... 9
Venting Requirements........................................................ 9
PLAN VENT SYSTEM............................................................... 10
INSTALL VENT SYSTEM ......................................................... 12
MAKE GAS CONNECTION...................................................... 12
CONNECT INLET HOSES........................................................ 12
CONNECT VENT ...................................................................... 14
LEVEL DRYER.......................................................................... 14
COMPLETE INSTALLATION CHECKLIST .............................. 15
REVERSE DOOR SWING......................................................... 15
TROUBLESHOOTING.............................................................. 17
INSTALLATION NOTES
Date of purchase:_________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
Date d'achat :_____________________________________
Date d'installation : ________________________________
Installateur : ______________________________________
Numéro de modèle :________________________________
Numéro de série :__________________________________
NOTES CONCERNANT L'INSTALLATION
Table des matières
SÉCURITÉ DE LA SÉCHEUSE ........................................18
EXIGENCES D'INSTALLATION .......................................20
Outillage et pièces .............................................................20
EXIGENCES D'EMPLACEMENT ............................................... 21
RACCORDEMENT DE LA SÉCHEUSE
ÉLECTRIQUE - CANADA SEULEMENT .................................. 22
Spécications électriques................................................. 22
RACCORDEMENT D'UNE SÉCHEUSE À GAZ ........................ 23
Spécications électriques................................................. 23
Spécications de l'alimentation en gaz ........................... 23
INSTALLATION DES PIEDS DE NIVELLEMENT ......................25
L'EVACUATION .......................................................................... 25
Exigences concernant l'evacuation .................................25
PLANIFICATION DU SYSTÈME D'ÉVACUATION..................... 26
INSTALLATION DU SYSTÈME D'ÉVACUATION....................... 28
RACCORDEMENT AU GAZ.......................................................29
RACCORDEMENT DES TUYAUX D'ALIMENTATION .............. 29
RACCORDEMENT DU CONDUIT D'ÉVACUATION .................31
RÉGLAGE DE L'APLOMB DE LA SÉCHEUSE ......................... 31
LISTE DE VÉRIFICATION
POUR INSTALLATION TERMINÉE............................................32
INVERSION DU SENS D'OUVERTURE DE LA PORTE............ 32
DÉPANNAGE .............................................................................. 34
Gas Dryer Installation Instructions
Canadian Electric Dryer Installation Instructions
Instructions pour l'installation de la sécheuse a gaz
(É.-U. et Canada) et électrique (Canada uniquement)
Para obtener acceso al “Instrucciones de instalación” en español, o para obtener información
adicional acerca de su producto, visite: www.whirlpool.com
Tenga listo su número de modelo completo. Puede encontrar el número de modelo
y de serie dentro de la cavidad superior de la puerta.

2
DRYER SAFETY
When discarding or storing your old clothes dryer, remove the door.

3

4
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed for all installations:
Level
Tape measure Pliers
Remove parts package from dryer drum. Check that all parts
are included.
Parts needed: (Not supplied with dryer)
Check local codes. Check existing electrical supply and venting.
See “Electrical Requirements” and “Venting Requirements”
before purchasing parts.
Mobile home installations require metal exhaust system hardware
available for purchase from the dealer from whom you purchased
your dryer. For further information, please refer to the “Assistance
or Service” section in your “Use and Care Guide”.
Parts supplied (all models):
Flat-blade screwdriver Adjustable wrench that
opens to 1" (25 mm) or
hex-head socket wrench
Tin snips (new vent
installations)
Caulking gun and compound
(for installing new exhaust vent)
Vent clamps
1/4"( 6 mm) nut driver
(recommended)
Tools needed for gas installations:
8" (203 mm) or 10"
(254 mm) pipe wrench 8" (203 mm) or 10"
(254 mm) adjustable wrench
(for gas connections)
Pipe-joint compound
resistant to LP gas
Utility knife
“Y” connector 2' (0.6 m) inlet hose
5' (1.5 m) Inlet Hose Rubber washer
Parts supplied (steam models):
INSTALLATION REQUIREMENTS
Leveling legs (4)

5
LOCATION REQUIREMENTS
You will need:
A location allowing for proper exhaust installation.■
See “Venting Requirements”.
A separate 15 or 20-amp circuit needed for gas dryers and■
30-amp circuit needed for electric dryers.
If using power supply cord, a grounded electrical outlet■
located within 2 ft. (610 mm) of either side of dryer.
See “Electrical Requirements”.
Floor must support dryer weight of 200 lbs. (90.7 kg).■
Also consider weight of companion appliance.
Level oor with maximum slope of 1" (25 mm) under entire■
dryer. If slope is greater than 1", clothes may not tumble
properly and automatic sensor cycles may not operate
correctly.
For garage installation, place dryer at least 18" (460 mm)■
above oor.
Steam models only: Cold water faucets located within 4 ft.■
(1.2 m) of the water ll valves, and water pressure of 20-100
psi (137.9-689.6 kPa). You may use the water supply for your
washer using the “Y” connector provided.
Do not operate your dryer at temperatures below 45° F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic sensor cycle. this can result in longer drying times.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
Check codes requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes, or
sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
DRYER DIMENSIONS
Optional Equipment: (Not supplied with dryer)
Refer to your “Use and Care Guide” for information about
accessories available for your dryer.
INSTALLATION CLEARANCES
The location must be large enough to allow the dryer door
to open fully.
NOTE: Most installations require a minimum of 5" (127 mm)
clearance behind dryer for exhaust vent with elbow. See “Venting
Requirements”.
Back view:
Bottom view:
Side view with open door dimensions:

6
Mobile home - Additional installation requirements:
This dryer is suitable for mobile home installations.
The installation must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile home
construction and Safety, Title 24, HUD Part 280) or Standard
CAN/CSA-Z240 MH.
Mobile home installations require:
All dryers:
Metal exhaust system hardware, available for purchase■
from your dealer. For further information, see “Assistance
or Service” section in your “Use and Care Guide”.
Special provisions must be made in mobile homes to■
introduce outside air into dryer. Openings (such as a
nearby window) should be at least twice as large as
dryer exhaust opening.
For gas dryers mobile home installations:
Mobile Home Installation Hold-down Kit Part Number■
W10432680 is available to order. For further information,
see “Assistance or Service” section in your “Use and
Care Guide”.
ELECTRIC DRYER
POWER HOOKUP- CANADA ONLY
ELECTRICAL REQUIREMENTS
It is your responsibility:
To contact a qualied electrical installer.■
To be sure that the electrical connection is adequate and in■
conformance with Canadian Electrical Code, C22.1-latest
edition and all local codes. A copy of above codes standard
may be obtained from: Canadian Standards Association,
178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.
To supply the required 4 wire, single phase, 120/240 volt,■
60 Hz, AC only electrical supply on a separate 30-amp
circuit, fused on both sides of the line. A time-delay fuse or
circuit breaker is recommended. Connect to an individual
branch circuit.
This dryer is equipped with a CSA International Certied■
Power Cord intended to be plugged into a standard 14-30R
wall receptacle. The cord is 5 ft. (1.52 m) long. Be sure wall
receptacle is within reach of dryer’s nal location.
4-wire receptacle (14-30R)
If using a replacement power supply cord, it is recommended that
you use Power Supply Cord Replacement Part Number 9831317.
For further information, please reference service numbers located
in “Assistance or Service” section of your “Use and Care Guide”.
Spacing for recessed area or closet installation
All dimensions show recommended spacing allowed, with tested
spacing of 0" (0 mm) clearance on sides and rear.
Additional spacing should be considered for ease of■
installation and servicing.
Additional clearances might be required for wall, door, and■
oor moldings.
Additional spacing should be considered on all sides of the■
dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation■
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilitation openings are
acceptable.
Companion appliance spacing should also be considered.■

7
GAS DRYER POWER HOOKUP
ELECTRICAL REQUIREMENTS
120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical■
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate
circuit serving only this dryer be provided.
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
� For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with
the dryer: if it will not t the outlet, have a proper outlet
installed by a qualied electrician.
GAS TYPE
Natural Gas:
This dryer is equipped for use with Natural gas. It is design-
certied by CSA International for LP (propane or butane) gases
with appropriate conversion.
Your dryer must have the correct burner for the type of gas■
in your home. Burner information is located on the rating
plate in the door well of your dryer. If this information does
not agree with the type of gas available, contact your dealer
or call the phone numbers referenced in the “Assistance or
Service” section of your “Use and Care Guide”.
GAS SUPPLY REQUIREMENTS
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
� For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualied electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with
the dryer: if it will not t the outlet, have a proper outlet
installed by a qualied electrician.

8
GAS SUPPLY CONNECTION REQUIREMENTS
Use an elbow and a 3/8" are x 3/8" NPT adapter tting■
between the exible gas connector and the dryer gas pipe,
as needed to avoid kinking.
Use only pipe-joint compound. Do not use TEFLON■®† tape.
This dryer must be connected to the gas supply line with a■
listed exible gas connector that complies with the standard
for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.
A. 1/2" NPT gas supply line
B. 3/8" NPT dryer pipe
NOTE: If the dryer is mounted on a pedestal, the gas pipe height
must be an additional 10" (254 mm) or 15.5" (394 mm) from the
oor, depending on the pedestal model. For a garage installation,
the gas pipe height must be an additional 18" (460 mm) from
the oor.
1/2" IPS pipe is recommended.■
3/8" approved aluminum or copper tubing is acceptable for■
lengths under 20 ft. (6.1 m) if local codes and gas supplier
permit.
If you are using Natural gas, do not use copper tubing.■
Lengths over 20 ft. (6.1 m) should use larger tubing and■
a different size adapter tting.
If your dryer has been converted to use LP gas, 3/8" LP■
compatible copper tubing can be used. If the total length of
the supply line is more than 20 ft. (6.1 m), use larger pipe.
NOTE: Pipe-joint compounds that resist the action of LP gas
must be used. Do not use TEFLON®† tape.
Must include shut-off valve■
In the U.S.A.:
An individual manual shut-off valve must be installed within
six (6) ft. (1.8 m) of the dryer in accordance with the National
Fuel Gas Code, ANSI Z223.1. The location should be easy to
reach for opening and closing.
In Canada:
An individual manual shut-off valve must be installed in
accordance with the B149.1, Natural Gas and Propane
Installation Code. It is recommended that an individual
manual shutoff valve be installed within six (6) ft. (1.8 m) of
the dryer. The location should be easy to reach for opening
and closing.
A. 3/8" exible gas connector
B. 3/8" pipe to are adapter tting
C. 1/8" NPT minimum plugged tapping
D. 1/2" NPT gas supply line
E. Gas shutoff valve.
LP Gas Conversion:
IMPORTANT: Conversion must be made by a qualied
technician.
No attempt shall be made to convert the dryer from the gas
specied on the model/serial rating plate for use with a different
gas without consulting your gas company.
GAS SUPPLY LINE
Must include 1/8" NPT minimum plugged tapping accessible■
for test gauge connection, immediately upstream of the gas
connection to the dryer.
A
B
E
D
C
†®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.
BURNER INPUT REQUIREMENTS
Elevations above 10,000 ft. (3,048 m):
When installed above 10,000 ft. (3,048 m) a 4% reduction■
of the burner Btu rating shown on the model/serial number
plate is required for each 1,000 ft. (305 m) increase in
elevation.
Gas supply pressure testing
The dryer must be disconnected from the gas supply piping■
system during pressure testing at pressures greater than
1/2 psi.
DRYER GAS PIPE
The gas pipe that comes out through the rear of your dryer■
has a 3/8" male pipe thread.
4 1/2"
(115 mm)
A
B
1"
(25 mm)

9
VENTING REQUIREMENTS
WARNING: To reduce the risk of re, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
Dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling, attic, crawlspace, or a concealed space
of a building. Only rigid or exible metal vent shall be used for
exhausting.
Rigid metal vent:
Recommended for best drying performance and to avoid■
crushing and kinking.
Flexible metal vent: (Acceptable only if accessible to clean)
Must be fully extended and supported in nal dryer location.■
Remove excess to avoid sagging and kinking that may■
result in reduced airow and poor performance.
Do not install in enclosed walls, ceilings, or oors.■
The total length should not exceed 7■3/4ft. (2.4 m).
NOTE: If using an existing vent system, clean lint from
entire length of the system and make sure exhaust hood
is not plugged with lint. Replace plastic or metal foil vents
with rigid metal or exible metal vents. Review Vent System
Chart and if necessary, modify existing vent system to
achieve best drying performance.
4"
(102 mm)
4" (102 mm) heavy metal exhaust vent
INSTALL LEvELING LEGS
2. Screw in leveling legs
Examine leveling legs. Screw legs into leg holes by hand,
use a wrench if necessary, to nish turning legs until they
begin to touch the base.
Now stand the dryer on its legs. Slide the dryer until it is
close to its nal location. Leave enough room for electrical
connection and to connect the exhaust vent.
Only a 4" (102 mm) heavy metal exhaust vent and clamps■
may be used.
Do not use plastic or metal foil vent.■
vENTING
Prepare dryer for leveling legs
1.
To avoid damaging oor, use a large at piece of cardboard
from dryer carton; place under entire dryer. Firmly grasp
dryer body (not console panel) and gently lay dryer down on
cardboard.
IMPORTANT: If laying dryer on its back, use the cardboard
corner posts the dryer was packed with to avoid damaging
the back of the dryer. Lay the dryer on its side if you do not
have the cardboard corner posts the dryer was packed with.

10
Optional exhaust installations:
Exhaust Cover Kit (to cover unused exhaust holes):■
Part Number W10186596 - all models
Bottom Exhaust Kit- Part Number 8212503■
PLAN vENT SYSTEM
Recommended exhaust installations
Typical installations vent the dryer from the rear of the dryer.
Other installations are possible.
B
B
C
D
E
F
G
H
A
A. Dryer
B. Elbow
C. Wall
D. Exhaust hood
E. Clamps
F. Rigid metal or exible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
Clamps:
Use clamps to seal all joints.■
Exhaust vent must not be connected or secured with screws■
or other fastening devices that extend into interior of duct
and catch lint. Do not use duct tape.
Vent products can be purchased from your dealer. For more
information, see “Assistance or Service” section in your “Use
and Care Guide”.
Louvered Hood
Good
Angled Hood
Box Hood
Better
Exhaust hoods:
Elbows:
Recommended Styles:
Recommended Styles:
45° elbows provide better airow than 90° elbows.■
Must be at least 12" (305 mm) from ground or any object■
that may obstruct exhaust (such as owers, rocks, bushes,
or snow).
Acceptable Style: