Whirlpool VB-100 User manual

INSTRUCTION MANUAL
Vacuum Cleaner
Model No.: VB-100
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.

1. Parts and components overview
Note: Illustations may differ from actual product.
1. Hose inlet 9. Dirt container
2. Lid release button 10. Dusting brush
3. Carry handle 11. Telescopic extension tube
4. Auto cord rewind button 12. Accessories holder
5. Floor tool parking slot 13. Crevice tool
6. On/Off button 14. Flexible hose
7. Wheel 15. Combination floor tool
8. Dirt container release button 16. Upholstery tool / Curtain brush

2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions should always be observed, including the
following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains
supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum
hose and accessories.
4. Children should be supervised to ensure
that they do not play with the appliance.
5. The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
6. Use only as described in this manual. Use
only the manufacturer’s recommended
attachments.
7. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped
into water. Do not use the vacuum cleaner
with a damaged cord or plug. If the supply
cord or plug is damaged, return the vacuum
cleaner to a Whirlpool Authorised Service
Agent or suitably qualified person for
examination, repair or adjustment.
8. Do not pull or carry by the cord. Do not use
the cord as a handle, close a door on the
cord or pull the cord around sharp edges or
corners. Do not run the vacuum cleaner over
the cord. Keep the cord away from heated
surfaces.
9. Do not handle the plug or vacuum cleaner
with wet hands. Do not use outdoors or on
wet surfaces.
10. Do not put any objects into openings. Do not
use with any openings blocked and do not
restrict air flow. Keep all openings free of
dust, lint, hair or anything that may reduce
airflow.
11. Keep hair, loose clothing, fingers and all
parts of the body away from openings and
moving parts.
12. Do not pick up hot coals, cigarette butts,
matches or any hot, smoking or burning
objects.
13. Do not pick up flammable or combustible
materials (lighter fluid, petrol, kerosene, etc)
or use in the presence of explosive liquids or
vapours.
14. Do not vacuum up harmful or toxic material
(chlorine bleach, ammonia, drain cleaner,
etc).
15. Do not vacuum up hard or sharp objects
such as glass, nails, screws, coins, etc.
16. Do not use without the filters in place.
17. Take extra care when vacuuming stairs.
18. Keep vacuuming area well lit.
19. Store the vacuum cleaner indoors in a cool,
dry area.
20. Turn off the on/off switch before unplugging
the vacuum cleaner.
21. Use only CE-approved 13 amp extension
cords. Nonapproved extension cords may
overheat. Care should be taken to arrange
the cord so that the cord cannot be pulled or
tripped over.
WARNING: Always switch off and unplug
the vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting
the attachments.
CAUTION: The vacuum cleaner is a very
powerful unit. Before plugging the cord into the
electrical outlet, make sure the switch is in the
‘off’ position.
IMPORTANT: If the inlet, hose or telescopic
tube is blocked, switch off the vacuum cleaner
and remove the blockage(s) before re-starting
the vacuum cleaner.
IMPORTANT: Cleaning filters improves
vacuum performance. Make sure all the filters
are completely dry before inserting back into the
vacuum cleaner.
This vacuum cleaner is intended for household
use only and not for commercial or industrial use.

3. How to Assemble
IMPORTANT: Always unplug the vacuum cleaner from the electrical outlet
before assembling or removing the accessories.
1. Insert the flexible hose connector into the
inlet on the main body of the vacuum
cleaner until it clicks into place.
2. Push the telescopic extension tube on to the
end of the handle.
3. The telescopic extension tube can be
lengthened or shortened by pushing the
button in and sliding the tube apart or
together as required.
4. Fit the combination floor head by pushing
onto the extension tube.
4. How to Operate
Cord Release
Fully unwind the power cord. A yellow mark on the power cord indicates the recommended cord length.
Do not exceed the cord length beyond the red mark.
On/Off Button
Insert the power plug into the electrical outlet. Ensure the vacuum cleaner is switched off.
Press the on/off button located on the top of the vacuum cleaner and press the button again to turn the
vacuum cleaner off.
Carpet Cleaning
For carpet and rug cleaning press the rocker switch on the combination floor head to raise the brushes.
Hard floor Cleaning
For hard floor cleaning, press the rocker switch on the combination floor head to lower the brushes.
Cord Rewind
To rewind the power cord, press the cord rewind button, located on the top of the vacuum cleaner, and
guide the power cord with one hand. This will prevent the cord from whipping which could cause damage
or injury.
Carry Handle
Use the carry handle located on the top of the vacuum cleaner to move the vacuum cleaner from room to
room.
Hose Storage
For convenience there is a slot located at the rear of the vacuum cleaner where the floor tool and hose
can be parked for storage.

5. Accessories:
The accessories can be attached directly to the handle by removing the telescopic tube and pushing in
the desired accessory.
The accessories can also be attached to the telescopic tube for extra reach. Remove the combination
floor head and push on the desired accessory.
Crevice tool: for crevices, corners and cracks, etc.
Dusting brush: for delicate surfaces.
Upholstery tool / Curtain brush: for curtain, carpet, upholstery, stairs, etc.
6. Dirt Container & Filter Removal and Replacement:
NOTE: Before emptying the dirt container and removing or replacing any filters the hose
must be removed from the vacuum.
WARNING: Always unplug the vacuum cleaner from the electrical outlet before
removing the dirt container.
WARNING: Do NOT use the vacuum cleaner without ALL of the filters in place.
NOTE: For best performance, replace filters annually.
Press and hold in the latch on the top of the hose connector and remove the connector away from the
vacuum cleaner
Emptying the Dirt Container
Lift the lid of the vacuum cleaner by pressing in the lid release buttons on the vacuum cleaner.
Rotate the dirt container anti-clockwise and lift the container out of the vacuum cleaner

Position the dirt container over a rubbish bin and press the dirt container release catch.
When all the dirt has fallen close the dirt container base, and return the dirt container to the vacuum
cleaner.
Cleaning the Filters:
NOTE: NOTE: Do not use any detergents or boiling water to wash the filters. Whirlpool
recommends checking the filters every time the dirt container is emptied and cleaning
as instructed below.
NOTE: All filters must be in place before using the vacuum cleaner.
Central Pre-motor Filter
Remove the dirt container as directed above.
Remove the central filter as shown:
The Central filter and filter can be rinsed in
warm water (max 40oC). Allow to air dry
completely before replacing.
Return the central filter, shroud and filter
sleeve to the dirt container. Replace the
dirt container as directed, ensuring that it
locks into place rotating clockwise before
the lid is closed.
The filter can be separated into two separate
parts.
Gently tap the central filter, filter shroud and filter
sleeve against the side of a rubbish bin to remove
excess dirt

Post-motor filter:
NOTE: This is located on the back of the vacuum cleaner.
Release the post-motor cover by pressing down on the catch at the top of the cover.
Remove the filter and case by pulling away from the casing then separate the filter from the case.
The post-motor filter can be rinsed in warm water (max 40oC). Allow to air dry for at least 24 hours before
replacing.
Return the post-motor filter to the casing and re-fit to the back to the vacuum cleaner.
8. Storage
IMPORTANT: Always unplug the vacuum cleaner from the electrical outlet and
rewind the power cord as directed before storing.
NOTE: Always store the vacuum cleaner base down.

9. Troubleshooting
WARNING: To reduce the risk of personal injury, unplug the vacuum cleaner
before performing maintenance or troubleshooting checks.
PROBLEM: Vacuum cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in securely.
Cause: No electricity in the electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Blocked central filter.
Solution: Remove, clean and replace filters. See page 6.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won’t pick up/loss of suction.
Cause: Dirt container not installed properly.
Solution: Review dirt container replacement.
Cause: Dirt container full or blocked.
Solution: Empty dirt container.
Cause: Clogged filters.
Solution: Remove, clean and replace filters.
PROBLEM: Accessories won’t pick up.
Cause: Accessories are not attached correctly.
Solution: Refer to section 5.
PROBLEM: Dust escaping from the vacuum cleaner
Cause: Dirt container full.
Solution: Empty dirt container.
Cause: Dirt container not installed correctly.
Solution: Review dirt container replacement.
Cause: Hose is not installed correctly.
Solution: Review installation.
Cause: Filter not installed completely.
Solution: Remove, clean and replace filters.
10. Technical Specification
Model: VB-100
Voltage: 220V ~50Hz
Power: 1400W
Capacity: 1.6 Litres approx
Cord length: 5M approx
*Subject to technical change without notice.
11. Service & Help
Please contact Whirlpool Service Centre:
Address : 14/F Wilson Logistics Centre, 24-28 Kung Yip Street, Kwai Chung, Hong Kong
Star Hotline : [phone]