Whirlpool VS2511 User manual

產品安全指引及使用說明指南
VS2511

2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
WARNING : To reduce the risk of fire, electric shock,
or injury:
1. Do not pick up detergent, kerosene, blizzard, nee-
dle, ash, wet dust, dirty water and match, etc. with
the vacuum cleaner.
2. To avoid filter blockage and motor damage, do not
pick up granule such as cement, land plaster, and
spitball.
3. Keep the vacuum cleaner away from fire and the
place of high temperature.
4. Caution: Always use the vacuum cleaner should be
assembled with HEPA and roller brush before op-
eration.
5. To avoid short circuit, keep the vacuum cleaner
away from water.
6. Recharge the battery when use it first time or the
battery is used up. Keep recharge and discharge
once three months when do not use it in long pe-
riod.
7. Unplug the plug when the vacuum cleaner recharge
finished, or during cleaning and maintenance.
8. When cleaning the vacuum cleaner, please use dry
cloth; do not use petrol and lacquer thinner which
will damage the surface.

3
9. Do not use if the plug or cord is damaged.
10. Switch the appliance off after use.
11. The charging base requires a 100-240V~, 50/60 Hz
supply. Do not use any other power source.
12. Only the supplied charging base should be used
with the appliance.
13. Never suck up water or any other liquid. Never suck
up flammable substances and do not suck up ash-
es until they are cold.
14. Do not immerse the body of the cleaner or the elec-
trical cord or plug in water or liquids.
15. Do not use attachments or accessories not recom-
mended by the manufacturer.
16. Close supervision is necessary when an appliance
is used near children. Children should not operate
this appliance.
17. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance
by a person responsible for their safety.
18. Children should be supervised to ensure that they
do not play with the appliance.
19. This appliance is for household use. Do not use for
any purpose not expressly specified in this manual.
20. There are no user serviceable parts in this appli-
ance. Unauthorised dismantling or servicing will
void the warranty.
21. Store the appliance away from direct sunlight, with all
accessories detached and out of the reach of children.

4
22. Caution: Only charge the vacuum cleaner with the
Charging bracket supplied. During charging, the
plug feels warm to the touch. This is normal.
23. Caution: Never block the exhaust air openings dur-
ing vacuuming.
24. Caution: Switch off the appliance when you re-
charged it.
SAVE THIS INSTRUCTIONS
THIS CLEANER WORKS BY SUCKING AIR AT HIGH
PRESSURE THROUGH A POWERFUL MOTOR. FOR EF-
FICIENT AND SAFE OPERATION IT IS ESSENTIAL
THAT ALL THE AIRWAYS AND FILTERS ARE CLEANED
AT REGULAR INTERVALS AND THAT THE DUST IS
EMPTIED BEFORE THE DUST CONTAINER IS FULL
AND AFTER EVERY USE OF THE APPLIANCE.
FAILURE TO CLEAN THE FILTERS AND EMPTY THE
DUST CONTAINER WILL RESTRICT THE AIRFLOW. THIS
WILL RESULT IN POOR CLEANER PERFORMANCE.
LONG TERM NEGLECT WILL BLOCK THE AIRFLOW
AND MAY DAMAGE THE CLEANER BEYOND REPAIR.
ANY DAMAGE CAUSED BY FAILURE TO CLEAN THE
FILTERS, AIRWAYS AND DUST CONTAINER AS SPECI-
FIED IN THESE INSTRUCTIONS WILL NOT BE COV-
ERED BY THE WARRANTY.
IMPORTANT NOTICE - PLEASE READ BEFORE USING
THIS PRODUCT!

5
1. Check the rating label of Bed Cleaner matches the
dedicated Handheld unit.
2. This Bed Cleaner is intended for normal household
use only. Do not use the appliance outdoors. Do not
use the appliance for other uses than its intended
use.
3. To protect against electrical shock, do not immerse
the Bed Cleaner in water or other liquids.
4. Do not store the Bed cleaner in areas with high
temperature, keep it away from heat sources such as
radiators or gas/electric fires.
5. If a blockage is found in the rotating brush, it should
be removed before use.
6. Do not continue to operate the appliance if you are in
any doubt about it working normally (e.g. abnormal
noise, smell, smoke), or if it is damaged in any way -
switch off, withdraw the mains plug and consult your
dealer.
7. The use of accessories not recommended by the
appliance manufacturer may cause injuries.
8. Never touch the appliance itself with wet hands.
9. Do not point the appliance at the eyes, ears or mouth
during operation.
10. Do not watch the power-on UV lamp directly, it may
cause damage to vision.
IMPORTANT SAFETY INSTRUCTIONS
(for Bed Cleaner)

6
1. ON/OFF switch
2. ECO speed switch
3. Foldable handle release
button
4. Handheld release button
5. Motorized brush
release button
UPRIGHT UNIT:
PRODUCT OVERVIEW
6. LED light
7. Motorized brush
8. Folding handle
9. Handheld handle
10. Handheld unit
11. Charging bracket
1
2
3
4
5
6
7
8
9
10
11

7
HANDHELD UNIT:
PRODUCT OVERVIEW
12. ON/OFF switch
13. Battery/ Charging indicator
14. Dust container release button
15. Seal ring
16. HEPA filter
17. Outer filter
18. Dust container
19. Adaptor
12
13
14
16
15
17
18
19
20
21
22
23
24
or
20. Extended crevice tool
21. Wide brush / Upholstery
adaptor
22. Wide brush
23. Upholstery
24. Flexible hose

8
APPLICATION OF ACCESSORIES
Adaptor:
Insert the Adaptor [19] into the inhale handheld nozzle of dust
container. It acts as an adaptor for the connection of accessories
for different purposes. To remove the Adaptor from dust container
just pull firmly outward.
Extended Crevice Tool:
Connect [20] Extended Crevice Tool is for cleaning small areas
which are difficult to reach, such as corners, gaps, holes, etc.
Wide Brush:
Insert and slide [22] Wide Brush into [21] Wide brush / Upholstery
adaptor. The Wide Brush is applicable for cleaning uneven surfaces,
such as hair, fibers, carpets, etc.
Upholstery:
Insert and slide [23] Upholstery into [21] Wide brush / Upholstery
adaptor. The Upholstery is applicable for cleaning textile surface,
such as shirts, curtain, bedding, etc.
Flexible hose:
Connect the Flexible hose [24] to accessories and Adaptor [19] at
both ends. The extension hose allows the vacuuming flexiblity to
reach some narrow and hidden areas.

9
Foldable Handle
PRODUCT ASSEMBLING
To lower the handle, press the
folding handle release button.
• Charging bracket assembly must be placed on a flat ground, mounting
screws and plastic wall anchors can fix the charging bracket on the wall.
• Mounting screws and plastic wall anchors are placed at the bottom
of the charging bracket. Drill the holes on the wall and put the plastic
wall anchors into holes, and then fixed the charging bracket with
mounting screws.
Off
Lift the handle to an upright
position, the handle will lock
automatically.
Assembling the Charging bracket
Wall Mount Hole
Mounting Screws
Plastic Wall Anchors
Detachable Motorized Brush Motorized Brush
LED Light
Motorized Brush
Release Button
Press

10
1. Insert the handheld unit to the upright unit
Make sure the upright unit is switched OFF. Avoid
any obstacles in between the hand-held unit and
the upright unit.
2. Attach the upright unit onto the charging bracket
˙Make sure the charging bracket is placed on a flat stable floor.
˙Attached the upright unit onto the charging bracket.
˙If the upright unit is not attached to the charging
bracket properly, charging will not start.
˙Avoid any dust in between the charging bracket
and the unit, clean the contacts if necessary.
˙Be careful of the unit will be tripped
over by the power cable during charging.
˙The charging indicator will illuminate red to
indicate that the vacuum cleaner is being charged.
NOTE: The charging indicator will turns to blue
when the battery is fully charged.
HINT: It is recommended to charge the vacuum
cleaner for at least 6 hours for before use.
˙It is normal that the charging bracket and the unit
will get warm while charging.
˙Even if the switch button is turned on, put the
vacuum cleaner back into the charging bracket,
the vacuum cleaner will be automatically stop working.
˙During the battery recharge process on charging bracket, the vacuum
cleaner has the circuitry protect feature. Even press on the switch
button, the product will be still in power-o mode.
3. Connect the power cable to the main socket
Socket for
Adaptor
Charge the battery when:
˙using the product for the first time
˙after not using the product for a long period of time
˙ when the unit is at low power and the battery/ charging indicator flashes red.
Light
on
Charging the Vacuum Cleaner
PRODUCT CHARGING

11
LED INDICATOR
Status LED color
Power ON Blue
Low battery Blue flashing
Empty battery Red flashing
Charging Red
Charging complete Blue
Bad battery Red & Blue alternative flashing
OPERATION
Make sure the battery is fully charged before use.
Operation of the upright vacuum cleaner
1. Press the ON/OFF switch to switch on the upright vacuum cleaner.
2. During the use, press the ECO Speed switch to shift between High
Speed and ECO Speed. In High Speed, the product suction power
will be in maximum while ECO Speed will be at relatively lower noise
level and with longer operation lead time.
3. During operation, the LED light on the floor brush will light up.
4. Always turn o the vacuum cleaner when the product is standing
upright on the ground because the brush bristles may damage the
floor or carpet.
5. When the product is not in used, it is recommended to store it
against the wall upright and children should be supervised to ensure
that they do not play with the appliance.
Operation of the handheld vacuum cleaner
1. Press the handheld button to detach the handheld vacuum cleaner
from the upright unit. Press the ON/OFF switch to turn on the
vacuum cleaner. The handheld vacuum cleaner will start to work.
2. Vacuum the surface in any direction until the area is clean.
3. Press the ON/OFF switch to turn o the vacuum cleaner. Slightly lift
the vacuum clenaer head upward to avoid dust falling out from the
dust container before switching o.
4. Empty the container before doing any more vacuuming and clean it
before putting it away.
5. Return the handheld vacuum cleaner to the upright unit.

12
MAINTENANCE & CLEANING
Empty the dust container
˙Dirt and liquid in the dust container should be emptied after each
use or at the time when the dust exceeds the maximum dust marking.
˙Always switch o the vacuum cleaner before cleaning.
1. Hold the vacuum cleaner vertically with the air-intake (nozzle end)
pointing downward to avoid spillage. Press the release button on
the top of the vacuum cleaner and release the dust container over a
rubbish bin and remove the filter bracket from the dust container.
2. Remove the filters by holding the two lips on the outer filter and
pull them out from the dust container.
3. Empty the contents of the dust container into the rubbish bin.

1313
4. Remove the filters and wash with water. Dry it before re-installing it.
NOTE: Do not clean the vacuum cleaner with paint thinner or
chemical solutions as this will damage the vacuum cleaner.
5. Fit the inner and outer filter into the dust container. Make sure you
have dried the inside of the dust container.
6. Re-install the dust container.
Caution:
˙Do not vacuum up large objects such as tissue papers. This will
cause a blockage and lower the suction power.
˙Never vacuum up flammable substances and do not vacuum up
ashes until they are cold.
˙Always dispose of the dust and clean the filter frequently,
otherwise the dust will damage the motor.

14
Maintenance when the motorized brush cannot be manually rotated
1. Slide the brush lock.
4. Remove the hair on the
rotating brush.
Lift up the right side of the
rotating brush, then take out
the rotating brush.
3. Take out the rotating brush.
Brush lock
Slide
Carry out the maintenance if any waste threads or hair gets tangled
in the brush. Press the motorized brush release button to detach the
motorized brush from the upright unit.
Regular Maintenance
Slowly rotate the brush manually
and remove any foreign objects
tangled around the brush.
Maintenance for Motorized brush
Take out
the dust
2. Rotate to open the brush door.
Scissors

15
5. Re-install the rotating brush back into the motorized brush

16
1. Bed cleaner body
2. Handheld unit release buttons
(2 buttons at two sides)
3. Dust spotting LED windows
4. Rotating brush (UV triggered device)
5. Rotating brush door
6. Front wheels (two sides)
7. UV lamp tube
8. UV lamp tube door
9. Rear wheel (UV triggered device) This Bed Cleaner must be operated with rated
Handheld unit of VS2511
PRODUCT OVERVIEW (for Bed Cleaner)
1
24
6
6
78
9
5
3
HOW TO USE THE UV BED CLEANER
1. Fit the Handheld unit onto the UV bed cleaner.

17
2. Press the Power Button on the Handheld unit to power on.
Power Button
Hold the Handheld unit tightly with one
hand, then press the two Handheld unit
release buttons with your other hand at
the same time to unlock.
Bedding surface
Slide
3. Slide on the surface of your bed to clean.
4. How to detach UV Bed Cleaner from Handheld unit.

18
NOTE
MAINTENANCE / CLEANING
There are totally two triggered devices at the rear wheel of UV bed
cleaner and rotating brush. UV lamp will be power on only when all
these two triggered devices are actuated.
Rear wheel
(UV triggered device)
1. How to clean the UV Bed Cleaner.
Use a wet towel or tissue to wipe the
cleaner, then let it dry before use.
Rotating brush
(UV triggered device)

19
Re-assemble the rotating brush and brush door to the UV Bed Cleaner
after cleaning.
a. Use your fingers to pull the two rotating brush door locks.
b. Then detach the door.
Take out the rotating brush,
and clean it.
Remove the hair on the
rotating brush.
Scissors
2. How to clean the rotating brush.

20
3. How to clean or exchange the UV lamp tube.
a. Use your fingers to pull the two UV lamp tube door locks.
b. Then detach the door.
a. Use your fingers to hold the UV lamp tube and then
rotate it by 90° clockwise or anti-clockwise.
b. Then take out the UV lamp tube.
After cleaning or exchanging the UV lamp tube, re-assemble the UV
lamp tube and the door to the UV Bed Cleaner.