Whirlpool AKR600IX User manual

T-BOX
DECORATIVE COOKER HOOD
AKR600IX / AKR900IX
INSTRUCTION MANUAL

1
Dear Customer,
If you follow the recommendations contained in this Instruction Manual, our appliance
will give you constant high performance and will remain efficient for many years to
come.
CONTENTS
RECOMMENDATIONS AND SUGGESTIONS
CHARACTERISTICS
INSTALLATION & USE
MAINTENANCE
Product Specification & Technical Parameters
Model AKR600IX / AKR900IX
Rated Voltage 220-240V~
Rated Power Frequency 50Hz
Light Power 2x20W 12V
Motor Power 250W
Total Power 290W
Motor 1
Diameter of Exhaust Pipe 150mm
Dimension (mm) L 596/896 x W 500 x H 570-1020

2
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
* The manufacturer will not be held liable for any damages resulting from incorrect or
improper installation.
* Please read this instruction manual before installing and using this cooker hood.
Properly keep this instruction manual in a safe place for future reference.
* This cooker hood can be used either in the Ducted Mode (ducting fumes to the
outside) or in the Recirculation Mode (internal recycling). The choice of modes can
be left to customers.
* Only a qualified and trained service technician can undertake the work of installation
and servicing.
* Check that the mains voltage corresponds to the one indicated on the rating plate
fixed inside the hood.
* Check that the domestic power supply guarantees adequate earthing.
* Do not connect the hood to exhaust ducts carrying combustion fumes (boilers,
fireplaces, etc.)
* If the hood is used in conjunction with non-electrical appliances (e. g. gas burning
appliances), a sufficient degree of ventilation must be guaranteed in the room in order
to prevent the backflow of exhaust gas. The kitchen must have an opening directly
with the open air in order to guarantee the entry of clean air.
* The minimum distance is 750mm from the cooker hood to a gas hob, and is 650mm
to an electric hob. If the installation instructions for gas hobs specify a greater distance,
this must be taken into account.
NOTICE: Considering excessive weight, two or more people are required to install or
move this appliance. Failure to do so can cause physical injuries.
USE
* The cooker hood has been designed only for domestic use to eliminate kitchen
fumes.
* Never use the hood for purposes other than what it has been designed for.
* Never leave high naked flames under the hood when it is in operation.
* Adjust the flame intensity to direct it onto the bottom of the pan only; making sure
that it does not engulf the pan sides.

3
* Deep fat fryer must be continuously monitored during use: overheated oil can burst
into flame.
* The hood should not be used by children or person not instructed in its correct use.
MAINTENANCE
* Proper maintenance of the Range Hood will assure proper performance of the unit.
* Disconnect the hood from the main supply before carrying out any maintenance
work.
* Clean and/or replace aluminum grease filters and activated charcoal filters after
specified period of time.
* Clean the hood using a damp cloth and a neutral liquid detergent.
* DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of
such waste separately for special treatment is necessary.
WARNING!!
In certain circumstances electrical appliances may be a danger hazard.
* Do not check the status of the filters while the cooker hood is operating.
* Do not touch the light bulbs after appliance use.
* Do not disconnect the appliance with wet hands.
* Avoid free flame, as it is damaging for the filters and a fire hazard.
* Constantly check food frying to avoid that the overheated oil may become a fire
hazard.
* Disconnect the electrical plug prior to any maintenance.
* Children don’t recognize the risks of electrical appliances. Therefore use or keep the
appliance only under supervision of adults and out of the reach from children.
* Don’t use this product outdoor.
* This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
* There shall be adequate ventilation of the room when the range hood is used at the
same time as appliances burning gas or other fuels.
* There is a fire risk if cleaning is not carried out in accordance with instructions.
* Do not flambé under the range hood.

4
* The discharge air must not be discharged into a flue which is used for exhausting
fumes from appliances burning gas or other fuels.
CHARACTERISTICS
DIMENSIONS
COMPONENTS
Ref Q’ty Product Components
1 1pc Hood body, complete with: controls, lights, blower, filters, air
outlet adapter
2 1set Telescopic Chimney comprising
2.1 1pc Decorative Chimney Top
2.2 1pc Decorative Chimney Bottom
3 1pc Aluminum Exhaust Duct (source locally, not supplied)
4 1pc Charcoal filter (accessory)
5 1pc Wall or Roof Cap (source locally, not supplied)
Ref Q’ty Installation Components
6.1 1pc Chimney Mounting Bracket
6.2 1pc Hood Mounting Bracket
7 1set Damper (flaps)
8 1pc Oil Cup

5
9.a 5pcs Mounting Screws (ST 5 X 50MM)
9.b 2pcs Chimney Mounting Bracket Screws (M 4 X 10 MM)
9.c 3pcs Chimney Bottom Fixing Screws (ST 4 X10 MM)
10 5pcs Drywall Anchors
Ref Q’ty Documentations
14 1pc Instruction Manual
15 1pc Warranty Card

6
INSTALLATION & USE
Note 1 : On stainless steel hoods, carefully remove the plastic protective film from all
exterior surfaces of the hood and chimney prior to final installation.
Note 2: At least two people will be required to mount the hood.
WALL DRILLING AND BRACKETS FIXING (X=Y-260)
1. Draw a vertical line on the
supporting wall up to the ceiling,
or as high as practical, at the
centre of the area in which the
hood will be installed.
2. Draw a horizontal line at 650mm
above the electric hob or 750mm
above the gas hob.
3. Place one of chimney mounting
brackets 6.1 on the wall as shown
min. 20mm from the ceiling or upper limit aligning the centre (notch) with the
vertical reference line.
4. Mark the wall at the centre of the holes in the bracket.
5. Place the hood mounting bracket 6.2 on the wall as shown aligning the central
notches to the vertical reference line.
6. Mark the wall at the centre of the holes in the bracket.
7. Drill

10mm holes at all the centre points marked.
8. Fix the two brackets using the mounting screws and drywall anchors.
MOUNTING THE HOOD BODY
1. Hook the body onto the hood mounting
bracket 6.2 as shown.
2. Balance the hood body by slightly
adjusting the hood mounting bracket.
Gently lower the hood until it securely
engages the bracket.

7
DAMPER (FLAPS) FIXING
1. Fix the damper (flaps) into the air outlet adapter.
2. To be sure that the damper (flaps) is locked well on the air
outlet adapter, it should be flexible in opening and closing.
DUCT FIXING
Caution: To reduce the risk of fire, use metal ductwork only.
1. Attach an adequate length of

150mm round duct into
the recessed area of the air outlet adapter.
2. Secure the duct using two screws that have been already
fixed on the two sides of the air outlet adapter. Make sure
the duct is fixed well on.
CONNECTIONS
Ducted mode air exhaust system
Caution: To reduce the risk of fire, use metal ductwork
is preferred.
1. Decide where the ductwork will run between the
hood and the outside.
2. A straight, short duct run will allow the hood to
perform most efficiently.
3. Long duct runs, elbows, and transitions will
reduce the performance of the hood. Use as few
of them as possible. Larger ducting may be required for best performance with
longer duct runs.
4. Attach an adequate length of

150mm round duct to the air outlet adapter.
5. The air must not be discharge into a flue that is used for exhausting fumes from
appliances burning gas or other fuels" "Regulations concerning the discharge of
air have to be fulfilled.
6. Install a roof/wall cap. Connect round metal ductwork to cap and work
back towards hood location. Use duct tape to seal the joints between
ductwork sections.

8
Recirculation Mode
Caution: Do not use plastic or rigid metal ducting.
1. Determine the length of the compressed flexible aluminum
ducting. Attach an adequate length of

150mm round duct
to the air outlet adapter.
2. Install the charcoal filter on.
3. Please note that the air will flow out from the two grids on the
sides of the decorative chimney top.
Electrical Connection
* Electrical wiring must be done by a qualified person(s) in accordance with all
applicable codes and standards. Turn off electrical power at service entrance
before wiring.
* If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
* Do not use the plug and an extension cord other than the ones initially supplied with
the hood.
* The earthing of this hood is compulsory. Do not remove ground prong of the plug.
TELESCOPIC CHIMNEY COMPRISING ASSEMBLY
Decorative Chimney Top
Raise the decorative chimney top 2.1 up inside the decorative
chimney bottom 2.2. Secure decorative chimney top 2.1 to the
chimney mounting bracket 6.1 that is well fixed on the wall with
the two chimney bracket screws 9.b supplied from two sides.
Decorative Chimney Bottom
1. Carefully slide the decorative chimney bottom 2.2 down outside the decorative
chimney top 2.1. Carefully place the decorative chimney
bottom 2.2 into the recessed area of the hood body top.
2. Fix the Decorative Chimney Bottom 2.2 with the three
decorative Chimney Bottom screws 9.c supplied from
inside of hood body.

9
OPERATION OF CONTROLS
The hood is operated using the push button on the front panel.
The light switch turns the lamps on and off.
The blower switch turns the blower on to three speed settings:
0 - OFF
1 - LOW SPEED
2 - MEDIUM SPEED
3 - HIGH SPEED
4 – LIGHT
MAINTENANCE
GREASE FILTER
* The grease filters should be cleaned frequently (every two months of operation, or
more frequently for heavy use). Use a warm detergent solution.
* Grease filters are washable.
1. Remove the grease filter one by one by pulling
out each latch. This will disengage the filter from
the hood. Tilt the filter downward and remove.
2. Wash the filters, taking care not to bend them.
Allow them to be dry before refitting.
3. When refitting the filters, make sure that the handle is visible from the outside.
4. To install the grease filter, align rear filter tabs with slots in the hood. Pull out the
latch, push filter into position and release. Make sure the filter is securely
engaged after assembly.
NON-DUCTED RECIRCULATION CHARCOAL FILTER
This filter is not washable, can not be regenerated, and should be replaced
approximately every 3 months of operation, or more
frequently in the case of heavy usage.
1. To install the charcoal filter, and lock it until the
stop click is heard.
2. Install grease filter after charcoal filter is
installed.