5019 301 10258/A
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
describedin your Instructions for Use. Close thedoor
and turn the programme selector to the desired
programme and temperature. The indication lamp
next to the “Start/Pause” button flashes.
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch
offautomatically.Unsuitablecombinationsofoptions
are deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
“Cold wash” button
• Water is heated only up to 20°C
• Suitable for delicate laundry items with wash
temperature recommendation of max. 30° on
the care label.
• Selectable only on the lowest temperature step
of each programme.
“Easy ironing” button
• Can be used together with “Cotton” ,
“Synthetics” and “Daily load”
programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very gently.
“Variable spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
CONSUMPTION DATA
Programme Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 95 5.0 49** 1.90 2:00
Cotton*** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50** 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Lingerie 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature,
the load and the type of wash.
*The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Openthetapandpressthe“Start/Pause”button .
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator
shows the current programme phase, running from left
to right through Wash, Rinse, Spin/Drain.
• When the programme phase is finished, the
corresponding indication goes out.
Before starting and after end of a programme, the
lamplights to showthatthe door canbe opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lightingupofthe“Service”indicationcanbecausedby
a fault in an electrical component. Refer to the
“TroubleshootingGuide”in yourInstructions for Use;
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Wastewaterisnotpumpedout.Checkwhetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence
indicator are off, and the “Door open”
indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the “Start/Pause” button to pause
the programme. The light flashes.
2. Selectthe newprogramme (withtemperature),
any options and another spin speed if you want.
3. Press the “Start/Pause” button again. The
new programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme
before the end.
•Pressthe“Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
Downloaded From WashingMachine-Manual.com Manuals
