5019 301 20159
Whirlpool is a registered trademark of Whirlpool USA.
Theuseoftheprewashcycleincreasesprogrammedurationbyapproximately15 min.Consumptiondatawascalculated
based on normalized conditions in compliance with Standard IEC 60 456. The data on the “Energy Label” refers to
programme“Coloured Cotton60°C”.Consumptiondatainthehomemayvarywithrespecttothevaluesinthetablein
relationtothewatersupplypressureandtemperature,theloadandthetypeofwash.Thedryingtimesshownmayvary
based on the spin speed and type of fabric.
Addthedetergentasdescribedintheprogramme
tableorinthechapter“DetergentandAdditives”in
the booklet.
1. MakesurethattheProgrammeselectorissetto
“Stop”.
2. Open the water tap.
3. Set the Programme Selector to the desired
programme.
4. Set the thermostat knob to the desired
temperature.
5. Setthespinselectorknobtothedesiredspeed.
6. Special options can be selected, if required.
7. Checkthatthedooriswellclosedandturnonthe
washer-dryer by pressing the “ON/OFF”
button.Theindicatorlightcomeson,indicating
that the washer-dryer is on.
“Dryer half load” button
(depending on model)
“Intensive Rinse” button (depending on
model)
• Thequantityofwaterdurationoftherinsecycle
are increased.
• Thisoptionisespeciallyrecommendedinareas
with extremely soft water, for baby linen and
linen belonging to skin allergy sufferers.
“Rinse and Hold” button (depending on
model)
only for synthetic andwool programmes
• The laundry remains in the final rinse water
without progressing to the final spin cycle to
avoidcreasingandpreventcoloursfromrunning.
• Thisoptionisparticularlyrecommendedforthe
programmes “Synthetics” or “Delicate”.
• This function is particularly useful if you want to
postponespinningtoalatertimeorwhenyoudonot
wish to spin the clothes.
To terminate the “Rinse and Hold” option
(depending on the model)
synthetic and woolprogrammes only
• PresstheRinseandHoldbuttonagain;theload
will be spun according to the selected
programme.
If you do not wish to spin the clothes, turn the
programmeselectorknobtothe Draincycle,after
pressing the “No Spin“ button.
“Spin Speed Reduction” Button
Reducesorincreasesthespinspeedfrom1000to
550.
CONSUMPTION DATA
Programme Temperature
Selector
()
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme Duration
(hours:minutes)
1 - Cotton 90° 5.0 57 1.85 2:28
2 - Cotton 90° 5.0 50 1.07 2:08
3 - Cotton 60° 5.0 53 0.97 2:00
4 - Cotton 40° 5.0 53 0.60 1:55
5 - Synthetics 60° 2.5 60 0.83 1:15
6 - Synthetics 60° 2.5 60 0.42 1:00
7 - Wool 40° 1.0 61 0.32 0:48
ADD THE DETERGENT, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT THE DESIRED OPTIONS
Thedoorlocksautomaticallyaftertheprogramme
start until the end of the programme. If the
programmeselectorismovedtothe“Stop”position
orifthe electricity supply is interrupted, thenafter
approximatelytwominutesthedoorisreleased.In
thiscasedonotopenthedoor:becausehotwater
could come out of the door.
Tochangeaprogrammewhenacyclehasalready
begun:
1. Switch off the appliance by pressing the
“ON/OFF” button.
2. Select the new programme.
3. Start the programme by pressing the
“ON/OFF” button.
Tointerrupttheselectedprogrammeandcontinue
it at a later time:
1. Press the “ON/OFF” button.
2. Afterthedesiredintervalhaspassed,pressthe
“ON/OFF” button again.
1. Attheendoftheprogrammetheprogramme
selector moves to the “Stop” position.
2. To unload the machine wait for the door to
release (approx. 2 minutes).
3. Switchofftheappliance,openthe door and
unload the washing.
4. Closethewatertapandleavethedoorajarto
allow the drum to dry out.
1. Loadthemachineaccordingtothemaximum
drying load table.
Thedryingfunctioncanonlybeusedforcotton
and synthetic programmes (not wool) and
startswhentheknobreachestheprogramme
stop mark.
Itisimportantthatthelaundryhasbeenspun
and was washed with water.
2. Whenthespincycleisfinishedtheprogramme
selector moves to “Stop”.
3. Selectadryingtimebasedonthetypeoffabric
(cotton/synthetic), amount of laundry and
desiredfinalresults(iron/cupboarddry),using
the “Drying Time” knob.
4. Press the“Dryer Half Load” button.
5. Turnonthewatertap,checkthedrainhose,
use the
“ON/OFF” buttontoturnon(theindicator
light goes on).
1. Thesequentialwashinganddryingfunction
can only be used for energy-saving and
syntheticprogrammes (notwool)andstarts
whentheknobreachestheprogrammestop
mark.
2. Loadthewasher-dryer(accordingtothemax.
drying load table) and close the door
3. Selectadryingtimebasedonthetypeoffabric
(cotton/synthetic), amount of laundry and
desiredfinalresults(iron/cupboarddry),using
the “Drying Time” knob.
4. Press the“Dryer Half Load” button.
5. Set the “Washing Programme” knob to the
desired programme
6. Press the“ON/OFF” button to start the
drying cycle.
•CLEANING THE FILTER
To ensure smooth operation of the pump,
check the filter regularly and clean it when
necessary.
DOOR LOCK
CHANGING THE SELECTED
PROGRAMME
INTERRUPTING THE CURRENT
PROGRAMME
AT THE END OF THE WASH PROGRAMME
SETTING THE DRYING CYCLE
SETTING THE WASHING/DRYING CYCLE
IN SEQUENCE
NOTES AND INDICATIONS FOR USE
3gb20159.fm5 Page 2 Wednesday, January 9, 2002 6:04 PM