Whirlpool WDC1070 User manual

Front Load Washer & Dryer
Combo
User Guide
Model: WDC1070
This washing machine is designed for HE high-efficiency
washing detergent.

2
Index
1. Safety Information ...........................................................................3
1.1 Important Safety Instruction ........................................................ 3
2.Installation Guide ..............................................................................5
2.1 For installation or dismantling of the washer............................... 5
2.2 Electrical and water pressure requirements.................................. 7
2.3 Installing the washer .................................................................... 8
2.4 Cleaning the washer................................................................... 10
3.Product Functions............................................................................11
4. Caring for your laundry ................................................................12
5. Using the Washer............................................................................14
5.1 Place laundry inside the washer................................................. 14
5.2 Adding washing detergent to the detergent drawer.................... 15
5.3. Operating the washer ................................................................ 16
6. Cleaning the Washer......................................................................24
6.1 Cleaning the washer interior ...................................................... 24
6.2 Cleaning the washer exterior...................................................... 24
6.3 Cleaning the detergent drawer ................................................... 25
6.4 Cleaning the rubber water hose filter......................................... 26
6.5 Cleaning the rubber door seal .................................................... 26
6.6 Cleaning the loose object collection compartment..................... 27
7. Troubleshooting..............................................................................28
8. Product Warranty..........................................................................34
9. Product Specification .....................................................................35
10. Support and Service......................................................................36
11. Dealer Information .......................................................................36
Note: This user guide includes all diagrams and explanations.

3
1. Safety Information
1.1 Important Safety Instruction
Yours and others’safety is an important matter.
This guide provides important safety measures and information
regarding the use of the product. Please read this User Guide and
installation instructions and all other information enclosed with the
washer carefully and act accordingly.
This sign warns that yours or others’safety may
be at risk. This sign together with the words
‘DANGER’or ‘WARNING’represents the following:
Danger
Immediate non-compliance may cause
injury or damage
Warning
Non-compliance may cause
injury or damage
Please note the following for your safety while using the washer:
Strictly follow installation guide
when installing the washer.
Read carefully all instructions when
using the washer.
This washer is designed for household
use only.
This product is not designed for use by
persons who have limited physical,
sensory or mental abilities and by
persons who have inadequate
experience or knowledge (children
included), provided they are supervised
or have been instructed by a responsible
person.
Do not install and place the washer
where it is exposed to rain or other
Do not attempt to maintain, repair or
change any parts of the washer on your
own
Read installation guide in detail, paying
weather conditions.
Do not leave children unattended near
the washer when it is operating.
To be operated with cold drinking water
and commercially available detergents
and care products which are suitable for
use in washers.
Do not use with items of laundry
pre-treated with cleaning agents
containing solvents, e.g. stain
remover / cleaning solvent may cause
fire hazard or explosion.
Do not attempt to maintain, repair or
change any parts of the washer on your
own
During high temperature washing or
drying, wait for temperature to drop to a
safe level, when the door would
automatically unlock.

4
special attention to electrical
requirements.
Read installation guide in detail, paying
special attention to electrical
requirements.
Before disposing the washer at the end
of its use, disconnect the main plug,
sever the main cable and discard along
with the plug. Destroy the lock on the
washer door to prevent children from
locking themselves in and risking lives.
Do not reach into the drum if it is still
rotating.
Never insert/disconnect the mains plug
with damp hands.
Do not place heavy objects above the
washer.
Do not operate the washer during gas
leaks.
Do not place the washer near gas stoves
or any fire source, or place burning
cigarettes, lit candles or other flammable
objects on/ above the washer.
The following may cause
damage to laundry items:
Do not wash water-proof items such as
rain gears, down jackets, sleeping bags
etc..
The washer is designed for household
use only, and meant for washing laundry
items that are suitable for washing and
drying. Check the washing and care
instructions on your laundry items before
washing.
Socks, lingerie and other small or
delicate laundry items are best placed in
laundry bags (not provided with the
washer) to avoid damages.

5
2. Installation Guide
2.1 For installation or dismantling of the
washer
When you encounter difficulties during installation or usage of the washer,
please call Whirlpool local agent to seek advice of arrange for maintenance
or repairs.
WARNING
Risk of injury during installation
This washer requires two or more persons to carry and install. Not
following this instruction may cause spinal or other serious injuries.
1. Remove all accompanying items from the
washer drum:
User guide
Rubber water hose
bolt hole cover
hex wrench (for removing bolt hole
cover and adjusting feet of the
washer )
washing detergent measuring spoon
detergent compartment separator plate (refer to
single sheet explanation note)
2. Two persons are required to remove the protective
plastic base from the bottom of the washer.
The base must be removed before use, without which
the washer may sustain damages.

6
3. Remove four sets of installation kit
attached to four corners at the back of the
washer. Each set consists of a screw,
washer and plastic retainer (A).
Use the smaller end of the hex wrench provided, loosen the screw by about 2cm
(B). Move hex wrench horizontally to the round opening (C). Pull the screw, washer
and plastic retainer out at the same time.
4. Loosen the wire on the plastic retainer.
Wire can only be removed after
the kit is pulled out.
5. Plug the gap with the bolt hole cover (E)
Referring to Diagram E, insert the plastic
plug into the circular opening where the
arrow is pointing towards.
Press down the protruded portion in the
centre.
Push the bolt hole cover in to plug the
gap, following the arrow direction.
Important:
Installation kits must be removed before using the washer, or it may sustain
damages when in operation.
Parts
Screw
Washer
Plastic Retainer

7
2.2 Electrical and water pressure requirements
1. A 2-pin plug is provided with each washer:
the plug
complies with the standards in your country, to be
connected to a power socket that complies to the standards. Please
ensure a good functioning 20A 2-pin socket is
used with the plug.
2. Check the 220V electrical socket and ensure it
meets the voltage requirement labeled on the
provided cable.
WARNING
Electrical Shock Hazard
Please ensure the electric connection is properly
grounded.
Please do not remove the ground connection
Please do not use adapter or Ts (3-pin plug adapter)
Please do not use an extension cord.
Not following this guide may cause fire or lead to
electrical shock and harm lives.
3. A 220V/ 60Hz/ 20 amp power socket that comes with fuse wire.
Dedicated power supply, enhanced safety wire and circuit breaker are
recommended. Please engage a qualified electrician to install.
Important Notice
If the electrical cable is spoilt, please contact Whirlpool, Whirlpool’s
local agent or qualified personnel for replacement. Please refer to
Whirlpool website for contact numbers.
Important:
Please retain the four sets of installation kit for future use, when
moving the washer.

8
4. A dedicated water tap for the washer is recommended.
If such
an option is not available, connect rubber water hose to any
existing tap, but ensure that a ¾inch O ring is used to secure
the tap and pipe from leaking.
Recommended water pressure is between 20 to 800 kPa (approximately 0.2 - 8.0
kgf/cm2, equivalent to 2 - 80m water pressure, which is higher than
normal water tap level). Water temperature should be between 5-30 degree °C to
ensure the normal functioning of the washer.
2.3 Installing the washer
1. Affix the rubber water hose for discharging water to the
smallest pipe with a 5cm diameter. After removing the
curved pipe, push the rubber hose inwards and upwards. If a
dedicated rubber water hose is not available,
retain the curved pipe for directing water discharge into water
pail or tank.
Important Notice
The curved end of the rubber water hose for
discharging water must be fixed at a height
between 0.85 to 1.2m.
If lower than 0.85m, the washer would not be able
to fill its tank with the amount of water required for
its operation.
If higher than 1.2m, it would not be able to
discharge used water.
Important Notice
Please do not connect the washer to a hot water tap, this will affect its drying
functions.

9
2. Using the curved end of the rubber water hose (F),
connect to the outlet at the top on the back of the washer
3. Secure the straight end of the rubber water hose (G) to
the top of the water tap with a screw.
4. Tighten till water does not seep through. Turn on the tap. If water
leaks through, tighten both ends of the rubber water hose. Do
not seal the connecting joints with tapes
5. Open the cover on the front bottom right of the
washer. Ensure that the filter cover is
tightened. To tighten, turn the filter cover clockwise till
it’s fully tightened. In addition, check to ensure the soft
pipe for discharging water
connected to the filter is tight as well.
6. Ensure that the washer is placed on a flat
surface, and that all four supporting feet are
even and stable to prevent and reduce vibration and noise
during operation.
7. Ensure there’s a minimum 10cm space between the
back of the washer and the wall, furniture or object it is
standing against.
Important Notice
The washer must not be placed in a spot exposed to
rain and weather elements. Do not place it on a
carpeted surface to avoid blocking its ventilation
system.
Important Notice
Please use the new rubber hose that comes with the
washer. Do not re-use old / used rubber water hose.

10
8. To check whether the washer is balanced, stand in front of the
machine, with hands placed on the top of the
machine, shake to see if it wobbles. If it does wobble,
check and adjust the height of the four supporting feet to
improve on its balance. Turn each supporting foot
clockwise to shorten its height, turn anti-clockwise to
lengthen it. All feet must touch the floor. Finally, using
the hex wrench accompanying the product, tighten the
nut with the larger end (H). Vibration, noise, leaks and wear
and tear can be reduced following this method.
9. Connect the plug to a power socket.
WARNING
Fire Hazard
Please do not place the washer near fire stoves, heaters or other fire or heat
source. Do not place lit candles, lanterns or other similar light
source. Ignoring this warning may lead to fire hazard and risk lives.
2.4 Cleaning the Washer
Before the use of the washer, please follow the following steps to
clean the interior of the machine:
1. Add 20ml detergent to the detergent box, approximately ⅓ of the measuring cup
provided with the washer.
2. Follow the operating guide on page 16. Choose ‘WASH’and ‘WHITES’programmes.
3. Allow the washer to complete the selected programme cycles.
Important Notice
The supporting feet provided with the washer are specially designed for the
product. Please do not replace with other feet, as this may cause unnecessary
vibration and damage to the machine.