Whirlpool Easy-Yo-Use Automatic Washer User manual

PART NO. 3363575
Easy-To-Use
Automatic Washers
A Note to You............ 2
Washer Safety ..........3
Parts and Features ... 4
Operating Your
Washer......................5
Caring for Your
Washer.................... 11
Troubleshooting ...... 12
Requesting
Assistance or
Service .................... 16
Index ....................... 17
Warranty ................. 20
TM

2
ANOTE TO YOU
Thank you for buying a WHIRLPOOL®appliance.
Because your life is getting busier and more complicated, WHIRLPOOL appliances are easy to use, save time,
and help you manage your home better. To ensure that you enjoy years of trouble-free operation, we developed
this Use and Care Guide. It is full of valuable information about how to operate and maintain your appliance
properly and safely. Please read it carefully.
Also, complete and mail the Ownership Registration Card provided with your appliance. The card helps us
notify you about any new information on your appliance.
Please record your model’s information.
Whenever you call to request service for your appli-
ance, you need to know your complete model number
and serial number. You can find this information on the
model and serial number label (see the diagram on the
“Parts and Features” page for the location of the label).
Also, record the other information shown in the next
column.
Keep this book and the sales slip together in a safe place for future reference.
Model Number __________________________________
Serial Number ___________________________________
Purchase Date __________________________________
Dealer Name ____________________________________
Dealer Address __________________________________
Dealer Phone ___________________________________
Our Consumer Assistance Center number is toll free. 1-800-253-1301
To find detailed product information, the location of the nearest Whirlpool dealer or authorized servicer, to
purchase an accessory item, or register your appliance on-line, please visit our Web site at
www.WhirlpoolAppliances.com

3
IMPORTANT SAFETY INSTRUCTIONS
WARNING – To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
•Read all instructions before using the
washer.
•Do not wash articles that have been
previously cleaned in, washed in, soaked
in, or spotted with gasoline, dry-cleaning
solvents, other flammable, or explosive
substances as they give off vapors that
could ignite or explode.
•Do not add gasoline, dry-cleaning sol-
vents, or other flammable, or explosive
substances to the wash water. These
substances give off vapors that could
ignite or explode.
•Under certain conditions, hydrogen gas
may be produced in a hot water system
that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used
for such a period, before using the wash-
ing machine, turn on all hot water faucets
and let the water flow from each for
several minutes. This will release any
accumulated hydrogen gas. As the gas
is flammable, do not smoke or use an
open flame during this time.
– SAVE THESE INSTRUCTIONS –
WASHERSAFETY
•Do not allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children.
•Before the washer is removed from service
or discarded, remove the door.
•Do not reach into the washer if the tub or
agitator is moving.
•Do not install or store the washer where it
will be exposed to the weather.
•Do not tamper with controls.
•Do not repair or replace any part of the
washer or attempt any servicing unless
specifically recommended in this Use and
Care Guide or in published user-repair
instructions that you understand and have
the skills to carry out.
•See Installation Instructions for grounding
requirements.
You will be killed or seriously injured if you don’t
follow instructions.
You can be killed or seriously injured if you don’t
follow instructions.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word “DANGER” or
“WARNING.” These words mean:
wDANGER
wWARNING
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

4
Heavy
Cold
OnOnOff
Super
Plus
Medium
Small
QuickWash
Load Size
5Cycle 2Speed Cycle Logic
Laundry SystemLaundry System
WashTemperature
ALLRINSES COLD
Extra Rinse
Normal
QuickWash
WrinkleResist
P.Press /
Pullto Star t
Pushto Stop
1-800-253-1301( In U1-800-253-1301( In U.S.A.)
ConsumerAssistance CenterAssistanceCenter
OFF
SpinSpin
RinseRinse
3
6
OFF
OFF
OFF
OFF
OFF
OFF
SpinSpin
ExtraExtra
RinseRinse
SpinSpin
RinseRinse
6
9
15
SpinSpin
ExtraExtra
RinseRinse
SpinSpinRinseRinse
CoolCool
DoDownwn
Pause
69
6
9
SpinSpin
ExtraExtra
RinseRinse
SpinSpin
RinseRinse
Heavy Duty SuperCapacity
Super Wash/ Heavy
Hand Washables
(IntermittentAgitate)
Delicates
HeavySoilHeavySoil
Towels/ Wowels / Work ClothesorkClothes
Whites
Super WSuperWash /Heavy
Hot
Normal
MixedColorsMixedColors HeavySoilHeavySoil
Cottons/ SheetsCottons/ Sheets
Quick Wash
1or 2 Items1or 2 Items
LightSoilLightSoil
Delicates/ Hand WHand Washables
Colorsthat BleedColorsthat Bleed
MediumSoilMediumSoil
Lingerie/KnitsLingerie/Knits
Warm Wrinkle Resist
MixedColorsMixedColors
MediumSoilMediumSoil
Shirts/BlousesShirts/Blouses
PARTS AND FEATURES
The parts and features of your washer are illustrated on this page. Become familiar with all parts
and features before using your washer. Page references are included next to some features. Refer
to those pages for more information about the features.
Cycle control knob
(pp. 7-9)
Liquid chlorine
bleach dispenser
(p. 5)
Model and serial
number label
(under lid)
Basket
Tub
Load size
selector
(p. 6)
Liquid fabric
softener
dispenser
(pp. 6, 11)
Agitator
MAGIC CLEAN®
lint filter
(bottom of
washer basket)
(p. 9)
Extra rinse selector
(p. 6)
Wash temperature
selector
(p. 6)
OnOff
Super
Super
Plus
Plus
Medium
Medium
Small
Small
QuickWash
Load Size
5 Cycle 2 Speed Cycle Logic
Laundry System
Extra Rinse
1-800-253-1301 ( In U.S.A.)
Consumer Assistance Center
Heavy Duty Super Capacity
Heavy Soil
Towels / Work Clothes
Whites
Super Wash/Heavy
Hot
Normal
Mixed Colors Heavy Soil Cottons / SheetsCottons / Sheets
Quick Wash
1 or 2 Items
Light Soil
Delicates / Hand Washables
Colors that BleedColors that Bleed
Medium SoilMedium Soil
Lingerie/ KnitsLingerie/ Knits
Cold
Warm Wrinkle Resist
Mixed Colors
Medium SoilMedium Soil
Shirts/ Blouses
WashTemperature
ALL RINSES COLD
Super Wash/Heavy
NormalQuickWash
OFF
Spin
Rinse
Hand Washables
(Intermittent Agitate)
Delicates
Wrinkle Resist
P. Press /
Pull to Start
Push to Stop
3
6
OFF
OFF
OFF
Spin
Extra
Rinse
Spin
Off
Off
Off
Rinse
6
9
15
Spin
Extra
Rinse
Spin Rinse
Cool
Down
Pause
69
9
6
Spin
Extra
Rinse
Spin
Rinse
CONTROL PANEL

5
To get the best washing results possible, you must use your washer correctly. This section tells
you how to use your washer properly and efficiently.
USING YOUR WASHER
OPERATING YOURWASHER
1. Measure detergent and pour it into the washer.
•If desired, you may
also add powder or
liquid color safe bleach.
•Add extra detergent
for the Super Wash/Heavy
cycle.
2. Drop a sorted load of clothes loosely into your
washer, filling to the
top row of holes.
•Load evenly to main-
tain washer balance.
Mix large and small
items.
•Items should move
easily through the wash
water. Overloading can
cause poor cleaning.
•To reduce wrinkling
of permanent press clothes and some synthetic
knits, use a large load size to provide more space
(see step 6).
continued on next page
3. (OPTIONAL STEP) Pour measured liquid chlorine
bleach into the liquid
chlorine bleach dis-
penser. Bleach will
be diluted automatically
during the wash part of
the cycle.
•Never use more than
1 cup (250 mL) for a full
load. Use less with a
smaller load size.
•Follow the manufac-
turer’s directions for safe use.
•To avoid spilling, use a cup with a pouring spout.
Do not let bleach splash, drip, or run down into the
washer basket.
•Make sure you use only liquid chlorine bleach in
this dispenser.
wWARNING
Explosion Hazard
Never place items in the washer that are
dampened with gasoline or other
flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any
type of oil on it (including cooking oils).
Doing so can result in death, explosion,
or fire.
wWARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire, or electrical shock.

6
6. Turn the Load Size selector to the correct setting
for your wash load and
the type of fabric being
washed.
•Your washer has
three load size set-
tings.
•Choose a load size
that allows the load to
move freely for best
fabric care. See the
“Loading” section.
•Change the setting after the washer has started
filling by turning the selector to a different setting.
OPERATING YOUR WASHER
USING YOUR WASHER (CONT.)
4. (OPTIONAL STEP) Pour measured liquid fabric
softener into the fabric
softener dispenser.
•Do not spill or drip
any fabric softener on
the clothes.
•Make sure you use
only liquid fabric
softener in this
dispenser.
7. Select a wash temperature with the Wash
Temperature selector.
The selections are
color-coordinated with
the cycles on the Cycle
Control Knob so you
can select a water
temperature that
matches the type of
fabric and soils being
washed.
•Follow garment label instructions.
HOT: 130°F (54°C) or above.
– Whites and pastels.
– Heavy and greasy soils.
WARM: 90 to 110°F (32 to 44°C).
– Bright colors.
– Moderate to light soils.
COLD: 70 to 90°F (21 to 32°C).
– Colors that bleed or fade.
– Light soils.
8. (OPTIONAL STEP) For an additional rinse and
spin at the end of a wash cycle, set the Extra
Rinse selector to On.
5. Close the washer lid.
•Dilute liquid fabric softener by filling the dis-
penser with warm
water until liquid
reaches the
crossbar in the
opening.
•Softener is added
automatically during
the rinse portion of
the cycle.

7
OPERATING YOUR WASHER
USING YOUR WASHER (CONT.)
9. Push in the Cycle Control Knob and turn it
clockwise to the wash
cycle you want. See
the “Cycle Descrip-
tions” section.
•Reduce the wash
time when using a
small load size setting.
10. Pull out the Cycle Control Knob to start the
washer.
NOTE: To stop the washer at any time, push in the
Cycle Control Knob. To restart the washer, close
the lid (if open) and pull out the Cycle Control Knob.
LOADING
Loading suggestions
For these suggested full-sized loads, set the Load Size selector to the highest load size setting.
SUPER CAPACITY PLUS WASHERS
Heavy Work Clothes
3 pair pants
3 shirts
4 pair jeans
1 coverall
1 overall
Towels
10 bath towels
10 hand towels
14 wash cloths
1 bath mat
Mixed Load
3 double sheets
4 pillowcases
8 T-shirts
6 pair shorts
2 shirts
2 blouses
8 handkerchiefs
Delicates
3 camisoles
1 quilted robe
4 slips
4 panties
2 bras
2 nighties
1 baby’s dress
SELECTING ACYCLE,TIME,AND TEMPERATURE
This section describes the available wash cycles
and temperatures, and will help you make the best
selections for your wash loads. Each cycle is
designed for different types of fabric and soil levels.
The labels next to the selections on the Wash
Temperature selector are recommended wash
cycles, load colors, and types of loads to use with
each temperature. To use your washer, simply
choose the cycle on the Cycle Control Knob that
corresponds with the one you chose on the Wash
Temperature selector. The selections are color-
coordinated to make washing easier.
•The washer pauses briefly throughout each cycle.
These pauses are normal. Refer to “Understanding
normal washer sounds” to learn more about the
sounds you may hear during a wash cycle.
•Refer to “Understanding what happens in each
cycle” to learn what happens during a wash cycle.

8
OPERATING YOUR WASHER
CYCLE DESCRIPTIONS
Hand Washables
The Hand Washables cycle features a series of brief,
extra low-speed agitations (7 seconds) and short
soaks (13 seconds) to gently clean special-care
items. Low spin speeds minimize wrinkling. Use this
cycle for cleaning lightly soiled hand washables.
Garments are labeled “Hand Wash” because:
•The fiber or construction may be sensitive to
agitation.
•The fabric contains sensitive dyes that may bleed.
Properly sort and then use your Hand Washables
cycle for gentle washing. Follow care label direc-
tions for drying. Items that may shrink should be
dried flat. Block these items by gently stretching to
original measurements. Woolens tend to shrink
more the first time they are washed.
•If items appear to be floating due to trapped air,
stop the washer by pushing in the Cycle Control
Knob. Push items down into the water. Restart the
washer.
Quick Wash cycle
The Quick Wash cycle features a reduced agitation
speed for gentle soil removal, while providing
shortened wash/rinse, drain, and spin times. Use this
cycle with a low water level and a warm wash to
quickly clean a few lightly soiled items.
Normal cycle
The Normal cycle features high-speed agitation
followed by a brief period of low-speed agitation for
cleaning cottons and linens. High spin speeds
shorten drying times. Select 6 or 9 minutes of wash
time, depending on whether your load is moder-
ately or heavily soiled.
Super Wash/Heavy – Select the 15-minute
Super Wash/Heavy feature to wash heavily soiled
loads that need maximum soil removal. Use two
times the amount of recommended detergent for
this cycle.
P. Press/Wrinkle Resist cycle
The P. Press/Wrinkle Resist cycle starts with
high-speed agitation and then steps to low-speed
agitation for cleaning permanent press blends and
synthetic fabrics. To minimize wrinkling, this cycle
features a cool-down rinse and a low-speed final
spin. Select 6 or 9 minutes of wash time to clean
light to moderately soiled loads.
Delicates cycle
The Delicates cycle features an extra low speed
agitation for gentle soil removal from delicate items
and washable knits. Low spin speeds minimize
wrinkling. Use this cycle for cleaning light to
moderately soiled loads.
Super Wash/Heavy
NormalQuickWash
OFF
Spin
Rinse
Hand Washables
(Intermittent Agitate)
Delicates
Wrinkle Resist
P. Press /
Pull to Start
Push to Stop
3
6
OFF
OFF
OFF
Spin
Extra
Rinse
Spin
Off
Off
Off
Rinse
6
9
15
Spin
Extra
Rinse
Spin Rinse
Cool
Down
Pause
69
9
6
Spin
Extra
Rinse
Spin
Rinse
Heavy Soil
Towels / Work Clothes
Whites
Super Wash/Heavy
Hot
Normal
Mixed Colors Heavy Soil Cottons / Sheets
Quick Wash
1 or 2 Items
Light Soil
Delicates / Hand Washables
Colors that Bleed
Medium Soil
Lingerie/ Knits
Cold
Warm Wrinkle Resist
Mixed Colors
Medium Soil
Shirts/ Blouses
WashTemperature
ALL RINSES COLD

9
OPERATING YOUR WASHER
RINSE/DRAIN AND SPIN
Rinse and Spin feature
When using extra detergent for heavily soiled
clothes, or washing special-care items, you may
find an extra rinse and spin is needed.
•For an additional rinse and spin, push in the
Cycle Control Knob and turn it clockwise to any
of the Rinse settings. The washer fills to the
selected load size, agitates, drains, and spins.
NOTE: An Extra Rinse option is also available. See
“Using your washer.”
Drain and Spin feature
A drain and spin may help shorten drying times for
some heavy fabrics or special-care items by remov-
ing excess water.
•For a drain and spin, push in the Cycle Control
Knob and turn it clockwise to any of the Spin
settings. Then pull out the Cycle Control Knob.
The washer drains, then spins.
Your washer has a self-cleaning lint filter at the
bottom of the basket. Wash and rinse water flow
over the filter during agitation, separating the lint
from the water. The lint spins out of the system
during the spin part of the cycle.
If your washer drains into a tub, remove any lint
collected in the tub or strainer.
MAGIC CLEAN
lint filter
Basket
interior
MAGICCLEAN®LINT FILTER
UNDERSTANDING NORMAL WASHER SOUNDS
During drain
If water is drained quickly from your washer (depend-
ing on your installation), you may hear air being
pulled through the pump during the end of draining.
After drain and before spin
When the cycle changes from draining to spinning,
you may hear gears engaging.
Your new washer may make sounds your old one
didn’t. Because the sounds may be unfamiliar, you
may be concerned about them. Don’t be; most of
them are normal.
The following describes some of the sounds you
may hear and what causes them.
During washing
When you select a small load size setting, your
washer has a lower water level. This may cause a
clicking sound from the upper part of the agitator.
OPERATING YOUR WASHER

10
UNDERSTANDING WHAT HAPPENS IN EACH CYCLE
When the Cycle Control Knob is set to a number
and pulled out, the washer fills (to the selected load
size) before agitation and timing start. The washer
begins agitating immediately after filling; agitation
occurs with the washer lid up or down.
During agitation, the XTRA ROLLACTION™ agitator
creates a continuous
rollover action that pro-
vides a thorough cleaning
of the wash load.
After agitation starts, the Cycle Control Knob turns
clockwise until it points to an Off area and the
cycle ends.
NOTE: The washer pauses briefly throughout
each cycle. These pauses are normal for washer
operation.
Sequence of cycles
Fill
▼
Rinse
▼
Drain-No agitation
▼
Spin-Spray rinse
▼
Spin
▼
Off
Fill
▼
Wash selected time
▼
Drain*
No agitation
▼
Spin
▼
WASH RINSE
* The Permanent Press cycle partially drains, fills, agitates
briefly, and drains.
OPERATING YOUR WASHER

11
CARING FOR YOUR WASHER
Proper care of your washer can extend its life. This section explains how to care for your washer
properly and safely.
CLEANING YOUR WASHER
Cleaning the exterior
Use a soft, damp cloth or sponge to wipe up any
spills such as detergent or bleach.
Occasionally wipe the outside of
your washer to keep it looking new.
Cleaning the interior
Clean your washer interior by mixing 1 cup (250 mL)
of chlorine bleach and 2 cups (500 mL) of detergent.
Pour this into your washer and run it through a com-
plete cycle using hot water. Repeat this process if
necessary.
NOTE: Remove any hard water deposits using
only cleaners labeled as washer safe.
Cleaning the liquid fabric softener dispenser
Flush dispenser periodically with warm water, as
shown. Remove the dispenser by grasping the top
of the dispenser with both hands and squeezing
and pushing upwards with thumbs. Clean the
dispenser by rinsing it under a water faucet.
Replace it after cleaning.
NOTE: Do not wash clothes with this dispenser
removed. Do not add detergent or bleach to this
dispenser; it is for liquid fabric softener use only.
WINTER STORAGE,MOVING,VACATION CARE
Install and store your washer where it will not
freeze. Because some water may stay in the hoses,
freezing can damage your washer. If storing or
moving your washer during freezing weather,
winterize it.
To winterize washer:
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 quart (1 L) of R.V.-type antifreeze in the
basket.
4. Run washer on a drain and spin setting (see
“Drain and spin”) for about 30 seconds to mix
the antifreeze and water.
5. Unplug the power supply cord.
To use washer again:
1. Flush water pipes and hoses.
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Reconnect power supply cord.
5. Run the washer through a complete cycle with
1 cup (250 mL) of detergent to clean out antifreeze.
Non-use or vacation care:
Operate your washer only when you are at home. If
you will be on vacation or not using your washer for
an extended period of time, you should:
•Unplug the power supply cord or turn off electrical
power to the washer.
•Turn off the water supply to the washer. This helps
avoid accidental flooding (due to a water pressure
surge) while you are away.

12
TROUBLESHOOTING
Most laundering problems are easily solved if you understand the cause. Check the following list
for common washing problems. If you need further assistance, see the “Requesting Assistance
or Service” section, on page 16.
COMMON WASHING PROBLEMS
Problem...
Washer leaks
NOTE: After
checking these,
check household
plumbing.
Washer won’t
drain/spin
Wet loads
Washer continues
to fill/drain or
cycle stuck
NOTE: Washer
pauses briefly
throughout each
cycle. This is normal.
Washer makes
noise
Solution...
•Tighten hoses. See Installation
Instructions.
•Reseat (reposition) washers. See
Installation Instructions.
•Clamp drain hose.
•Unclog drain. Sink and standpipe
must be able to handle 17 gallons
(64.6 L) of water per minute.
•Ensure tub is centered before
starting washer.
•Ensure front feet are installed and
nuts are tightened. Level washer.
•Redistribute the load, or reduce
load size.
•Unclog hose. See Installation
Instructions for proper installation
of drain hose.
•Close the lid.
•Lower drain hose.
•Use less detergent.
•Check electrical source or call
electrician. Do not use extension
cords.
•Choose a cycle with a higher spin
speed.
•Cold rinses leave loads wetter than
warm rinses. This is normal.
•Raise the drain hose. It must be
higher for proper operation.
•Adjust drain hose for loose yet
secure fit. See Installation
Instructions.
•Do not seal off drain hose with
tape. The hose needs an air gap.
•Redistribute load.
•Level washer. Reset rear leveling
legs. See Installation Instructions.
•Tighten nuts.
•See Installation Instructions.
Cause...
•Fill hoses not tight.
•Fill hose washers not properly seated.
•Drain hose clamp not properly installed
or is off.
•Drain is clogged.
•Tub moved forward during unloading,
causing water to deflect off of tub ring.
•Unit not level, causing water to deflect
off of tub ring.
•Fill or spray rinses are deflecting off of
load. Washer is overloaded or load is
unbalanced.
•Drain hose is clogged.
•Lid is open.
•End of drain hose more than
72 inches (190.9 cm) above floor.
•Too much detergent – excessive sudsing.
•Low voltage or using an extension cord.
•Wrong cycle for load being washed.
•Cold rinses.
•Top of drain hose is lower than water
level in washer.
•Drain hose fits too tightly into standpipe.
•Drain hose taped into standpipe.
•Load is unbalanced.
•Washer is not level.
•Nuts on front feet not tight.
•Yellow shipping strap with cotter pins
not completely removed.

13
COMMON WASHING PROBLEMS (CONT.)
Solution...
•This is normal.
•This is normal.
•Plug in power cord.
•Turn timer knob to the right
slightly and pull to start.
•Clean screens.
•Turn on water.
•Reverse hoses.
•Straighten hoses.
•Plug in power cord.
•Check electrical source or call
electrician.
•Replace fuse or reset circuit
breaker. If problem continues,
call electrician.
•Do not use extension cords.
•Turn timer to the right slightly
and pull to start.
•Set and pull out knob.
•Allow cycle to continue.
•Wash smaller loads.
•This is normal.
•This is normal.
•This is normal.
•Push tub to center before
starting.
•This is normal.
•Ensure front feet are installed
and nuts tightened. Level
washer. Reset rear leveling legs.
See Installation Instructions.
Cause...
•Gears engaging after drain and
before spin.
•Upper part of agitator clicks during wash.
•Power cord not plugged in.
•Timer dial is not lined up.
•Water inlet valve screens are plugged.
•Water is turned off.
•Hot and cold hoses are reversed.
•Inlet hose is kinked.
•Power cord not plugged in.
•No power at plug.
•Fuse blown or circuit breaker open.
•Using an extension cord.
•Timer dial is not lined up.
•Timer knob not pulled out.
•Washer at pause in P. Press/Wrinkle
Resist cycle (approximately 2 minutes).
•Machine is overloaded.
•The top of the agitator moves only in one
direction.
•The top of the agitator is loose.
•The top of the agitator is much higher
than the highest water level. This creates
a perception of the washer not being full.
•Tub is pulled forward when unloading.
•Tub moves.
•Unit not level.
Problem...
Washer makes noise
(cont.)
Won’t fill/rinse/agitate
or wrong temperature
Washer stops
Agitator operation
Water level seems
too low or washer
not completely filling
Washer tub is crooked
TROUBLESHOOTING
continued on next page

14
TROUBLESHOOTING
COMMON WASHING PROBLEMS (CONT.)
Solution...
•Sort lint givers (towels, chenille) from
lint takers (corduroy, synthetics). Also
sort by color.
•Lint can be trapped in load if over-
loaded. Wash smaller loads.
•Clean out pockets before washing.
•Use enough detergent to hold
lint in water.
•Use wash water warmer than 70°F
(21°C).
•Use wash water warmer than 70°F
(21°C).
•Loads should move freely during
wash. Wash smaller loads.
•Do not pour chlorine bleach directly
on load. Wipe up bleach spills.
Undiluted bleach will damage fabrics.
•Clean out pockets before washing.
Zip zippers before washing.
•Mend rips and broken threads in
seams before washing.
•Dilute fabric softener and add to rinse
portion of cycle only. Do not drip
fabric softener on clothes.
•Install an iron filter.
•Use enough detergent to remove soil
and hold it in suspension.
•Sort dark clothing from whites and
lights.
•Unload the washer as soon as it
stops.
•Unload the washer as soon as it
stops.
•Use the P. Press/Wrinkle Resist cycle
or another cycle with low spin speeds
to reduce wrinkling.
•Loads should move freely during
wash. Wash smaller loads.
•If safe for fabric, use warm or hot
wash water. Use cold rinse water.
•Reverse hoses.
Cause...
•Improper sorting.
•Overloading.
•Paper or tissue in pockets.
•Not enough detergent.
•Detergent not dissolving.
•Wash water colder than 70°F (21°C).
•Overloading. Improper use of washer.
•Improper use of chlorine bleach.
•Sharp items not removed from pockets;
fasteners not fastened.
•Items damaged before washing.
•Improper use of fabric softener.
•Iron (rust) in water.
•Not enough detergent used, causing soil
to be redeposited.
•Dye transfer due to not sorting loads
properly.
•Dye transfer due to not unloading
washer promptly.
•Not removing load promptly.
•Wrong cycle for fabrics being washed.
•Overloading.
•Wash water not warm enough to relax
wrinkles. Using warm rinses.
•Hoses reversed.
Problem...
Residue or lint
on load
Tearing
Stains on load
Load is wrinkled

15
COMMON WASHING PROBLEMS (CONT.)
Problem...
Load is tangled/
twisted
Clogged dispensers
or bleach leaking
Gray whites,
dingy colors
Solution...
•Loads should move freely during
wash. Wash smaller loads.
•Do not wrap items around agitator.
•Dilute fabric softener in the dispenser.
•Add powder or liquid color safe bleach
directly to the basket. Do not use
chlorine bleach dispenser for color
safe bleach.
•Always measure bleach before adding
to the dispenser. Carefully pour into
the dispenser. Wipe up bleach spills.
•Sort dark clothes from whites and
lights.
•Use hot or warm washes if safe for
fabric. Hot water should be at least
130°F (54°C) to clean heavy or
greasy soils.
•Use more detergent for washing
heavy soils in cold or hard water.
•Use more detergent when washing
in hard water.
Cause...
•Overloading.
•Clothes wrapped around agitator.
•Not diluting softener.
•Use of color safe bleach in chlorine
bleach dispenser.
•Improper use of chlorine bleach.
•Dye transfer.
•Wash temperature too low.
•Not enough detergent.
•Hard water.
TROUBLESHOOTING

16
If you need to order replacement parts, we recom-
mend that you only use FSP®factory authorized
parts. FSP replacement parts will fit right and work
right, because they are made to the same exacting
specifications used to build every new
WHIRLPOOL®appliance.
REQUESTING ASSISTANCE OR SERVICE
To avoid unnecessary service calls, please check the “Troubleshooting” section. It may save you
the cost of a service call. If you still need help, follow the instructions below.
IFYOU NEED ASSISTANCE OR SERVICE
Call the Whirlpool Consumer Assistance Center
toll free at 1-800-253-1301. Our
consultants are available to
assist you.
When calling:
Please know the purchase date, and
the complete model and serial number of your
appliance (see “A Note to You” ). This information
will help us better respond to your request.
Our consultants provide assistance with:
•Features and specifications on our full line
of appliances
•Installation information
•Use and maintenance procedures
•Accessory and repair parts sales
•Do-it-yourself repair help
•Specialized customer assistance (Spanish speak-
ing, hearing impaired, limited vision, etc.)
•Referrals to local dealers, service companies, and
repair parts distributors.
Whirlpool service technicians are trained to fulfill
the product warranty and provide after-warranty
service, anywhere in the United States.
To locate the authorized Whirlpool service company
in your area, you can also look in your telephone
directory Yellow Pages.
IFYOU NEED REPLACEMENT PARTS
To locate FSP replacement parts in your area, call
our Consumer Assistance Center telephone number
or your nearest authorized service center.
FOR FURTHER ASSISTANCE
If you need further assistance, you can write to
Whirlpool with any questions or concerns at:
Whirlpool Brand Home Appliances
Consumer Assistance Center
c/o Correspondence Dept.
2000 North M-63
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your
correspondence.
Gearcase assembly
covered by your
warranty.

17
INDEX
This index is alphabetical. Look for the word or phrase you are interested in, then look for the
page number.
TOPIC PAGE
ASSISTANCE .............................................................16
CLEANING
Exterior ...................................................................11
Interior .................................................................... 11
Liquid fabric softener dispenser ............................. 11
CYCLES ....................................................................... 8
DISPENSERS
Liquid chlorine bleach .............................................. 5
Liquid fabric softener ...............................................6
EXTRA RINSE .............................................................. 6
FEATURES/PARTS ......................................................4
LINT FILTER .................................................................9
LOADING .....................................................................7
OPERATING ........................................................... 5-10
TOPIC PAGE
PARTS/FEATURES ......................................................4
RINSE/DRAIN AND SPIN .............................................9
SAFETY ........................................................................3
SOUNDS ......................................................................9
STORAGE .................................................................. 11
TROUBLESHOOTING .......................................... 12-15
WARRANTY ...............................................................20
WASHER OPERATION
Selecting a cycle and time ................................... 7-9
Selecting a load size ................................................ 6
Selecting a temperature ...........................................6
Stopping/restarting .................................................. 7
Using the dispensers............................................ 5, 6
Using your washer.................................................... 5

18
NOTES

19
NOTES

20
PART NO. 3363575
© 1997 Whirlpool Corporation ® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Outside the United States, a different warranty may apply. For details, please contact your authorized
Whirlpool dealer.
If you need assistance or service, first see the “Troubleshooting” section of this book. After checking “Trouble-
shooting,” additional help can be found by checking the “Requesting Assistance or Service” section. In the
U.S.A., call our Consumer Assistance Center at 1-800-253-1301.
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation of your washer.
2. Instruct you how to use your washer.
3. Replace house fuses or correct house wiring or plumbing.
B. Repairs when your washer is used in other than normal, single-family household use.
C. Pickup and delivery. Your washer is designed to be repaired in the home.
D. Damage to your washer caused by accident, misuse, fire, flood, acts of God, or use of products not
approved by Whirlpool.
E. Any labor costs during the limited warranties.
F. Replacement parts or repair labor costs for units operated outside the United States.
G. Repairs to parts or systems caused by unauthorized modifications made to the appliance. 11/96
WHIRLPOOL®
AUTOMATIC WASHER WARRANTY
WHIRLPOOL WILL PAY FOR
FSP®replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by an authorized Whirlpool
service company.
FSP replacement parts for any part of gearcase assembly if defective in
materials or workmanship. The gearcase assembly is shown in the
“Requesting Assistance or Service” section of this book.
FSP replacement parts for any top and lid rust.
FSP replacement parts for outer tub should it crack, or fail to contain
water, due to defective materials or workmanship.
LENGTH OF WARRANTY
FULL ONE-YEAR
WARRANTY
FROM DATE OF PURCHASE
LIMITED FIVE-YEAR
WARRANTY
FROM DATE OF PURCHASE
LIMITED TEN-YEAR
WARRANTY
FROM DATE OF PURCHASE
7/97
Printed in U.S.A.