WHITECROFT LIGHTING CENTURION PP65 Assembly instructions

May 2014 - Rev E
Whitecroft Lighting Limited
Burlington Street, Ashton
-under-
Lyne, Lancashire OL7 0AX
Telephone [phone] Facsimile: [phone]
Registered No. 3848973 England
Registered Office: As above
SITING AND POSITIONING
1) Only mount the fitting at a point that is stable, secure and strong enough to
maintain it in its desired orientation in the most severe weather conditions.
2) Do not mount your fitting on a flammable surface and do not focus it on any
object less than 1.0m away.
3) Do not position fitting in an enclosure or other location which has restricted air
flow.
4) Thought should be given to the siting of the dusk/dawn photocell sensor versions
of the floodlight. The light switching level will be affected if the unit is situated under
the eaves of a building or if the sensor is obscured from the ambient light falling on
the surface during daylight conditions.
GENERAL INFORMATION
1) A qualified electrician, in accordance with IEE wiring regulations should carry
out connection to mains wiring.
2)Prior to supply electrical power to the fitting, first ensure all voltages,
frequencies and fusing conforms with the specifications supplied within these
instructions.
3) This unit must be EARTHED.
4) Ensure that the rated voltage and frequency requirements are compatible with
the available mains supply.
5) Cleaning of reflectors and lenses should be carried out using clean, soft and lint
free damp cloths and soapy water.
6) Do not carry out high voltage insulation test, i.e. 500/1000v this may damage
internal components.
7) We recommend use of a high temperature Copper Paste on all screws that
need to be accessed during maintenance process, this will prolong the life of the
fixings and reduce the force required to remove the screws.
8) Some luminaires installed in outdoor environments may experience a build-up
of internal condensation. This is due to a difference in temperature between inside
and outside the luminaire which is quite common and acceptable under
BSEN60598. TECHNICAL SUPPORT
Telephone: [phone]
E-mail: [e-mail]
http://www.whitecroftlighting.com/
Exterior Perimeter Security Bulkhead
Installation And Wiring Instructions
CENTURION PP65
Fusing :
• Power Factor: 0.90
• 28/38 watts, 4 amps (1-5 fittings per circuit)
• 70-80 watts, 4 amps (1-4 fittings per circuit)
• 70-80 watts, 6 amps (1-6 fittings per circuit)

INSTALLATION DETAILS
1) Take the fitting from its packaging
and locate the small plastic bag
containing; split ring, four No8x5/8
screws, four nylon washers and a
20mm cable gland complete with
associated lock-nut and rubber seal.
2) Remove the reflector by first
loosening the two securing screws, but
do not unscrew. Slide the top of the
reflector down, enough to release the
reflector from the location slot, then
release the lower half by lifting the
reflector out (fig 1).
SPECIFICATION
Lamp type 26W TC-D, 42W TC-T, 70W SON-E, 70W
HQI-E
Finish Black
Materials Body Polycarbonate
Diffuser Polycarbonate
Weight Maximum weight of fitting is 3.0Kg
Supply 230 - 240V AC, 50Hz
Operating temp -30oC to 25 oC
Connection Minimum Cable Size 2.5mm²
Ingress protection IP65
Lamp Performance Wattage IL@25oC Lamp Life
26W TC-D 1800 13,000hrs
42W TC-T 3200 13,000hrs
70W SON-E 5810 28,500hrs
70W HQI-E 7230 12,500hrs
3) A knock-out for a 20mm cable gland is located on either side of the base.
Carefully remove the desired knock-out and secure the gland. To maintain the IP
integrity of the luminaire, correctly locate and secure the rubber seal and lock-nut (fig 2).
NB. Never wire the fitting using flat ‘twin & earth’ cable since this could affect the IP
rating and allow ingress of moisture. Use a minimum of 2.5mm2 mains cable of circular
cross section only.
4) Prepare the two key-hole slots and two mounting holes on the base of the fitting, then
secure the base in its desired location using appropriate screws (fig 2). Ensure that the IP
integrity of the fitting is not impaired by the method of securing by screws through the
base.
5) Once the base is secured, check that the
mains supply is isolated and then feed the
supply cable through the selected cable
entry. Secure the cable via the saddle-bar,
ensuring enough spare inside the fitting to
make required termination.
6) Make the wiring connections from a suitably
fuse mains supply the luminaire; Live, Earth
and Neutral wires can now be connected to the
terminals of the 3- way screw connector block,
taking special note of the L E N positions.
Fig.2
Fig.1
7) Once all the wiring is complete, relocated the reflector into the base and
secure. Carefully fit appropriate lamp into the lamp-holder.
8) Secure the diffuser using the four No8x5/8 screws. Tighten only enough to
maintain the IP integrity of the luminaire (fig 3). NOTE: to avoid damaging the
diffuser – do not over tighten the fixing screws.
9) Finally fit the split ring through both the body and diffuser.
Dimensions and Fixing Hole Centres