whitesales CCU3 User manual

INSTALLATION GUIDE |08.10.21 |V 1.2
Europa House, Alfold Road, Cranleigh, GU6 8NQ |01483 917580 |[e-mail] |whitesales.co.uk
Standard Comfort Controls
These installation instructions should be used for:
Contents
2 Connections
3 Programming
4 Technical Data
4 Functions
5 Trouble Shooting

Europa House, Alfold Road, Cranleigh, GU6 8NQ |01483 917580 |[e-mail] |whitesales.co.uk
INSTALLATION GUIDE |08.10.21 |V 1.2 |2
Standard Comfort Controls
Connections
PLEASE NOTE:
The installation of all electrical items must be undertaken by a qualied professional.
Do not use cable thicker than 1.5mm and multi-strand if possible for exibility.
Wire all other inputs before connecting mains power.
To ensure perfect sealing of the control unit you must pass the cables through the grommets and insert the
rubber cord for tighter seal.
The RS1 rain sensor is supplied complete with 5 metres of cable. If this is not sufcient the cable can be
extended to a maximum of 50 metres using 3 x 0.5mm cable.

Europa House, Alfold Road, Cranleigh, GU6 8NQ |01483 917580 |[e-mail] |whitesales.co.uk
INSTALLATION GUIDE |08.10.21 |V 1.2 |3
Standard Comfort Controls
Programming Remotes
1. *Only if using 5 channel remote*
Select the channel you wish to programme using
the ‘channel select’ button on the remote control.
2. Turn on the power to the CCU3 control unit.
3. Short press the ‘LEARN’ button on the CCU3, the
buzzer will make a short sound (approximatley 4
seconds).
4. Within a few seconds press and hold the ‘STOP’
button on the remote transmitter.
5. The buzzer will sound several times to conrm
the remote transmitter has been programmed.
6. Operate the remote as required. Open/close may
require double quick press on rst operation.
To delete the remote controls stored on the CCU3
control units memory simply press and hold the
'LEARN' button for 10-15 seconds until the red LED
light ashes.

Europa House, Alfold Road, Cranleigh, GU6 8NQ |01483 917580 |[e-mail] |whitesales.co.uk
INSTALLATION GUIDE |08.10.21 |V 1.2 |4
Standard Comfort Controls
Technical Data
Code CCU3
Voltage (Input) 230V AC
Voltage (Output) 230V AC
Output Current 6 Amp
Protection Class IP54
Operating Temperature -10°C / +60°C
Dimensions 162 x 139 x 45mm
Inputs RS1, CCU3RC1, CCU3RCS, S50-1, RRTKEY
Functions
Rocker Switch:
Open:
Press the Open button and the actuator will fully
open.
Stop:
If the actuator is opening press the Close buttton
to stop the actuator in mid-position. Or if the
actuator is closing press the Open button to stop
the actuator.
Close:
Press the Close button and the actuator will fully
close.
Remote Control:
Open:
Press the Open button (1) on the remote and the
actuator will fully open.
Stop:
If the actuator is opening press the Close button
to stop the actuator in mid-position. Or if the
actuator is closing press the Open button to stop
the actuator.
Close:
Press the Close button (2) on the remote adn the
actuator will fully close.
*For multi-channel remotes rst select the correct
channel you wish to operate using the select
buttons (3 and 4).
Rain Sensor:
Close – When Rain is detected the Rain Sensor
will perform a full close cycle until rain is no longer
present. The Rain Sensor takes 1st priority so all other
inputs will be disabled while rain is still present.
Once rain is no longer present it will take up to 8
minutes before other inputs can be used.

Europa House, Alfold Road, Cranleigh, GU6 8NQ |01483 917580 |[e-mail] |whitesales.co.uk
INSTALLATION GUIDE |08.10.21 |V 1.2 |5
Standard Comfort Controls
Trouble Shooting
Should I test the unit when commisioning?
We would always recommend you carry out a
functionality check when rst commissioning the
unit by applying moisture (water or a damp cloth)
to the rain sensor to check unit closes correctly.
Once the rain function is activated, the control
module will time out for 8 minutes – you can reset
by turning off power to the CCU3 module for 10
seconds.
The unit doesn’t seem to close in the rain?
The system can be checked by opening the
rooight, so it is half open using switch or remote
handset.
Remove rain sensor wires from terminals 12 – 14
in CCU3 control module.
Use a small piece of wire to short across
terminals 13 & 14.
The rooight unit should close – this proves
the control unit is wired correctly and any issue in
non-operation would have to be with rain sensor
wiring or the rain sensor.
If the unit opens, then you need to reverse the
motor feed wires in terminals 2 & 3 (ensure power
is turned off rst).
If the motor neither opens or closes when
terminals 13 & 14 shorted out it would indicate the
CCU3 control module is likely suspect and should
be returned for testing and inspection.