Whittier Wood Furniture 2000W User manual

Assembly Instructions
2000W
24" Alder
Bookcase
2-Door Kit
P.O. Box 2827
Eugene, OR 97402 USA
For normal household use only.
recommended for commercial use.
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
2003W
30" Alder
Bookcase
2-Door Kit
2001W
36" Alder
Bookcase
2-Door Kit
Service Policy: We will replace any parts which
are defective, missing or damaged during assembly.
Please contact Whittier Wood Products customer
service department directly (by phone, fax, mail or
email) for replacement parts.
Hours: Our friendly customer service staff can
be reached Monday-Friday 7:00 a.m. to 5:00 p.m.
(Pacific Time). A message can be left 24 hours a
day, 7 days a week.
To Order: Provide the complete furniture model
number, part letter, production code, quantity
needed, reason for replacement and your full name
and address along with a telephone number in case
we need to contact you.
Parts ship from our Eugene, Oregon factory within
1 or 2 business days from the time we receive
the request. Please allow 5-10 business days for
delivery.
Outside U.S. or Canada: 541-687-0213
Fax: [phone] • Email: [e-mail]
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
05/08VN
Production Code:
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)

Page 2 — 2000W, 2001W, 2003W — 05/08
2000W, 2001W, 2003W Door Kit — Parts List
Before beginning assembly, check that the quantities of the parts received match those on the parts list below.
A — Door — Qty. 2
B — Door Knob — Qty. 2 C — #8x1½" Machine
Screw — Qty. 2
F — Pad — Qty. 2
D — Hinge — Qty. 4 E — Hinge Plate — Qty. 4

ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED: Phillips Head Screwdriver
1) Lay the Doors (A) face down on a clean protected surface. Snap the handle of the Hinge (D)
down on to each of the Hinge Plates (E) as seen in Figure 1 and 1a.
2)
Page 3 — 2000W, 2001W, 2003W — 05/08
2000W, 2001W, 2003W Door Kit
ED
Fig. 1
Fig. 2 Fig. 2a
A
There are pre-drilled holes in the door as shown in Figure 1a. This is where you will be inserting the
hinge part of the assembly. Insert the Hinge (A) assembly that has the plastic knobs into the pre-drilled
holes in the bottoms and tops of the Doors (A).See Figures 2 and 2a. You must place both Hinges
into the Door prior to attaching to bookcase.
E
D
Fig. 1a

4)
Page 4 — 2000W, 2001W, 2003W — 05/08
Side adjustment
Depth adjustment
To move the door towards the side panel, rotate screw ‘2’ counter-clockwise. To move it away,
rotate screw ‘2’ clockwise.
Loosen screw ‘1’ and adjust door. Re-tighten screw.
Height adjustment Loosen screws ‘3’ and adjust door. Re-tighten screws.
Fig. 4
1
2
3
3
The door may need to be adjusted so that all the spaces between the doors and unit sides are
equal. To make those adjustments, follow instructions in Figure 4.
Fig. 3 Fig. 3a
3) Attach the door to the bookcase by inserting the screws in the Hinge Plate (E) into the second
and third holes up from the bottom of the bookcase unit. See Fig. 3. Attach the second hinge
assembly to the same door/bookcase by inserting screws into the third and fourth predrilled holes
down from the top of the pre-inserted center shelf. See Figure 3a.
Bottom
Center
shelf

Page 5 — 2000W, 2001W, 2003W — 05/08
5) Attach the Knobs (B) to the Doors (A) with #8x1½" Machine Screws (C). See FIGURE 3.
DOOR
C
B
Phillips Head Screwdriver
6) Attach a Pad (F) to the back of each door where it comes in contact with the adjustable shelf.
Fx 2
Bx 2
Cx 2
Fig. 4