Whittier Wood Furniture 2091AFGSPc User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 10/13
Model #
2091AFGSPc;
2091AFCAFc
64"W Pacific
Sound Bar Console
AFGSP = Glazed Spice finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Handle the glass plates with care. Glass is fragile.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
This assembly requires two people.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Parts List
2091AFGSPc_2091AFCAFc —Page 2 —10/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
A
Top (attached)
1
B
Adjustable Shelf (attached)
4
Cc
Case
1
D
Removable Back (installed)
2
E
Door Frame (installed)
2
F
Door Glass (attached)
2
Ga
Speaker Door (attached)
1
H
Small Drawer Box (inserted)
2
I L
Small Drawer Face (installed)
2
J M
Large Drawer Box (inserted)
3
K
Large Drawer Face (installed)
3
L
Glass Retainer (inserted)
1
M
Shelf Bracket (installed)
16
N
#6 x 1/2" Undercut Screw (inserted)
16
P
Butler Hinge (attached)
2
Q
Magnetic Push Lock (attached)
2
R
#5 x 5/8" Flat Head Screw (inserted)
12 (AFGSP)
0 (AFCAF)
T
#6 x 5/8" Undercut Screw AB (inserted)
4
U
Drawer Slides (pre-installed sets)
5
V
#6 x 3/4" Philtruss Screw (inserted)
30
W
#6 x 1/2" Philtruss Screw (inserted)
34
YB
3mm x 12mm Pan Head Screw (inserted)
4

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Parts List
2091AFGSPc_2091AFCAFc —Page 3 —10/13
Part
Description
Quantity
YC
1/4" x 20mm Insert Nut (inserted)
4
YD
#8 x 1-5/8" Machine Screw (installed)
10
YE
#8 x 1-3/8" Lo-Profile Screw (inserted)
6
YI
Tuscan Magnetic Plate (attached)
2
YJ
#6 x 5/8" Undercut Screw ZN (inserted)
0 (AFGSP)
12 (AFCAF)
YK
#8 x 20mm Pan Head Screw (inserted)
4
YL
Foot Bracket (attached)
1
YM
Adjustable Glide (installed)
1
ZB
Small Adjustable Glide (installed)
4
ZD
Hinge (attached)
4
ZE
Hinge Plate (attached)
4
ZF
#6 x 3/4" P.O Screw (inserted)
16
ZG
Knob (attached)
2
ZH
#8 x 1-1/4" Machine Screw (installed)
2
ZI
Handle (attached)
5
ZK
Drawer Stop (attached)
4
ZL
Turn Button (attached)
8
ZM
#6 x 5/8" Philtruss Screw (inserted)
30
ZN
#8 x 1-1/4" Pan Head Screw (inserted)
33
ZP
#8 x 1-1/4" Black Screw (inserted)
25
ZQ
#8 x 1" Lo-Profile Screw (inserted)
20
ZR
Flat Washer (inserted)
2
ZS
Hex Bumper (attached)
2
ZT
Fitted Back (attached)
1
ZU
Speaker Spacer
2
ZV
Velvet Pad 340 x 19mm (attached)
4
ZW
Chain (attached)
2

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Parts List
2091AFGSPc_2091AFCAFc —Page 4 —10/13
Part
Description
Quantity
ZX
Cleat (attached)
1
ZY
Push Plate
2
ZZ
1/2" Dark Antique Brad
4
TS
Media Tipping Restraint (attached)
1 set

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 5 —10/13
Tool Required: Phillips Screwdriver, Pencil.
1. Place the console at its final destination. Rotate the Adjustable Glides (ZB) found at the corners
of the unit and (YM) at the bottom of the Center Foot until the unit is level. See Figure 1.
Step two is optional: Attach the Push Plates (ZY) when the console will be placed in a high-use
area such as a retail sales floor where the Sound Bar Speaker Door (Ga) will be opened and closed
often.
2. Remove the Speaker Door (Ga) and place it face-up on a clean protected surface. Center a
Push Plate (ZY) over the right Tuscan Magnetic Plate (YI) and attach with two 1/2" Dark Antique
Brads (ZZ). Repeat for the left side. See Figure 2. Attach the Door.
Fig. 1
ZB
ZB
YM
Fig. 2
ZY
ZZ
x 2
x 4
ZZ
ZY
YI
Ga
(back view)
ZZ
ZY
YI

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 6 —10/13
3. To open the Speaker Door (Ga), simultaneously press the Push Plates or both corners until the
magnets release. Gently grasp the middle of the door and pull it open. To shut the door, push
gently but firmly on the Speaker Door (Ga) until the two Tuscan Magnetic Plates (YI) make
secure contact with the Magnetic Push Locks (Q).
If you did not install the Push Plates, gently press on both corners until the magnets release.
See Figure 3.
If you need to install your sound bar from the back, remove the #6 x 1/2" Philtruss Screws (W)
and pull away the fitted back (ZT). After installing the component, replace the Fitted Back and
attach with the #6 x 1/2" Philtruss Screws.
4. If your center sound bar needs to sit above the edge of the speaker door, place the two Speaker
Spacers (ZU) into the sound compartment so the Velvet Pads (ZV) face down. Place the
speaker on top of the Spacers. See Figures 4 and 4a.
Fig. 4
Ga
ZU
ZU
Fig. 4a
ZU
Fig. 3
YI
ZT
Q
Ga
Q
YI

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 7 —10/13
5. To insert your media components and access wires into the console more easily, you may want
to remove the Removable Backs (D). To do so, unlock the Turn Buttons (ZL) as shown in
Figures 5 and 5b. Slide the Backs away and place them off to the side. To put them back into
place, slide the Backs behind the Drawer Stops (ZK) and position the Turn Buttons so that they
are locked. See Figures 5a and 5b.
6. Determine where you want to place the Adjustable Shelves (B). To support each shelf, tap the
Shelf Brackets (M) into the four holes with the flat side down. Insert the shelf as shown in Figure
6. You may fasten the brackets to the shelf by inserting a #6 x 1/2" Undercut Screw (N).
Repeat for each shelf. See Figure 6a.
Fig. 6
N
M
Fig. 6a
Door removed for illustration purposes.
B
B
ZL
Locked
Position
Fig. 5
Fig. 5a
Unlocked
Position
Fig. 5b
ZT
ZK
ZL
D
D
ZK

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 8 —10/13
7. To adjust the doors, follow the instructions below.
Continued on Page 9
Fig. 7a
1
Side adjustment 4mm (5/32")
To move the door towards the side
panel, loosen screw ‘1’and tighten
screw ‘2’. To move the door away
from the side panel, loosen screw
‘2’ and tighten screw ‘1’.
Depth Adjustment 4mm (5/32")
Loosen screw ‘2’ (just one turn),
adjust the door to the desired position
and tighten the screw.
Height Adjustment 4mm (5/32")
Loosen screw ‘3’, adjust the door to
the desired position and tighten
the screw.
3
3
2
Door
Hinge
Arm
ZD
Fig. 7
ZE
2

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 9 —10/13
Furniture Tipping Restraint Instructions
Before you begin this assembly, identify each part and make sure the quantities received match what is on this
list. If you need to replace a part, contact Whittier Wood Furniture customer service and refer to the following
list for its name and letter code.
Part
Description
Quantity
A
Cam Buckle and Short Strap (installed)
1
B
Plastic Bracket (installed)
1
C
1" x 1000mm Long Strap (installed)
1
D
#8 x 3" Pan Head Screw
2
E
#10 x 1" Oval Head Screw (inserted)
1
F
Washer
1
If you have a stone or tile floor or do not wish to drive screws into the corner of the baseboard
and floor see the instruction included inside the tipping restraint kit for an alternate
installation.
8. Decide where you want to place the piece of furniture in your room. Mark the baseboard with a
pencil mark directly behind the location where the tipping restraint is attached to your item.
Move the item away from the wall far enough to allow you to access the spot where the
baseboard meets the floor. Position the straps and Plastic Bracket (B) as shown in Figures 8
and 8a with the angled corners of the Plastic Bracket (B) firmly placed against the seam of the
baseboard and floor. Attach by driving #8 x 3" Pan Head Screws (D) through the holes in the
Plastic Bracket (B) into the seam below the baseboard where it meets the floor. See Figures 8
and 8a.
Fig. 8
Fig. 8a
Wall
Floor
D
Floor
Baseboard
D
x 2

2091AFGSPc; 2091AFCAFc 64"W Pacific Sound Bar Console
Assembly Instructions
2091AFGSPc_2091AFCAFc —Page 10 —10/13
9. Move the item back into position against the wall and reach underneath the piece of furniture to
grasp the loop in the free end of the strap. Pull the free end of the strap until portion between
the Cam Buckle (A) and the back apron of the item is tight. See Figures 9 and 9a. If you need
to move the piece of furniture reach beneath and locate the buckle which connects the two
sections of the strap and depress the release lever, then pull on the section of strap that is
between the buckle and the back apron of the furniture until there is enough slack to allow you
to pull the item away from the wall.
Fig. 9a
Fig. 9
C
Wall
Floor