why pro WHY-EP User manual

DUPLICATING PROCEDURES
DEDICATED TO
PROFESSIONALS
why-pro.com
WHY-EP

2
Totally enriched, in detail well-finished,
honouring the original design that gave the
success obtained till today.
An important news has been represented by
a default integration, on each button, of a 64
bit Sice Rolling code. This allows to use the
WHY-EP remote controls as a first installation
in combination with one of our SICE Tech
multifrequeuncy receiver. The further copies
and its insertion on the receiver happen simply
and directly.
WHY-EP
ANTI-SHOCK
NEW DESIGN
BI-COMPONENT MOLD
DOUBLE LED
WHITE-BLUE
GROWN
COMPATIBILITY LIST
INTENSIFIED POWER
SIGNAL

3
WHY-EP
1. While pressing the button 1 of the “WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHY-EP LED emits a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown in the picture).
4. Press and retain pressed the button of the original remote control and wait for a change flash (as a faster flash) of WHY-EP LED
and a change of its color that confirms the correct learning of code. This step may take a few seconds.
5. While the LED is flashing, press the button of the “WHY-EP” where you want to program the code just learnt, and retain pressed
until the LED switches o. This step may take some seconds.
6. The copy has been happened with success. Now check on the automation the correct functioning of the new WHY-EP remote
control.
Notes:
• If the LED flashes only 3 times and switches o, the code has not learnt correctly. Please repeat the operation from the step 1.
• The WHY-EP memory is completely re-writable.
• To duplicate further buttons of WHY-EP, please repeat the operation from the step 1.
FIXED CODE
DUPLICATING PROCEDURES
BEST POSITION FOR THE
DUPLICATION
5 cm
IT IS RECOMMENDED:
TO REALIZE A CORRECT DUPLICATION OF THE REMOTE CONTROLS, WE RECOMMEND TO
FOLLOW THE PROCEDURES HERE BELOW TAKING CARE TO DISTANCE YOURSELF BY TOOL
THAT CAN GENERATE FREQUENCY TROUBLES AS:
CORDLESS
WI-FI VIDEO SURVEILLANCE DEVICES
MOBILE PHONES, SMARTPHONES OR TABLETS
WI-FI OR BLUETOOTH ACTIVED IN YOUR COMPUTERS
ELECTRONIC MOTOR
NEON LIGHTS
WIRLESS DEVICES FOR BACK END MANAGEMENT IN THE BUSINESS STORES
ART. 4791001
WHY-EP

4
WHY-EP ROLLING SIMPLE
DUPLICATING PROCEDURES
1. While pressing the button 1 of the “WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHY-EP LED will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown in the picture).
4. Press and retain pressed the button of the original remote control and wait for a change flash (as a faster flash) of WHY-EP LED
and a change of its color that confirms the correct learning of code. This step may take a few seconds.
5. While the LED is flashing, press the button of the “WHY-EP” where you want to program the code just learnt, and retain pressed
until the LED will switch o.
6. The copy has been happened with success.
7. Activate now the correct procedure for the programmed model and insert the new remote control on the receiver (see the
compatibility list present in this manual).
Notes:
• If the LED flashes only 3 times and switches o, the code has not learnt correctly. Please repeat the operation from the step 1.
• The WHY-EP memory is completely re-writable.
• To duplicate further buttons of WHY-EP, please repeat the operation from the step 1.
To activate the remote control on the receiver for models marked with proceed as below:
1. First of all you must be closed to the automation.
2. Press and retain pressed the programmed button during 10 seconds, when the LED start to flash, release the button.
3. Wait until the LED will turn o. The operation has been done, now you can use your new remote control.
To activate on the receiver all the other models: Refer you to the instructions of the original model.
NOTE: THE SEED CODE OF THE WHY-EP CAM BE EMITTED AS HERE BELOW:
1. Press the buttons 1 and 2 simultaneously for 8 seconds and release them when the LED start to flash;
2. While the LED is flashing press the button with the seed code needed.
ATTENTION!! Every kind of receiver can have the “radio-mode” disarmed. In this cases will be necessary insert the new remotes controls with the “manual procedures”.

5
WHY-EP ROLLING COMPLEX
DUPLICATING PROCEDURES
1. While pressing the button 1 of the “WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHY-EP LED will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown
in the picture).
4. Press and retain pressed the button to be programmed of the original remote control, till the LED will switch on as a
fix light; now release the button.
5. The WHY-EP LED will emit a short flash every 2 seconds. That it informs the user that, to duplicate the remote
control, it is necessary to emit the SEED CODE to realize the copy.
6. Transmit now the SEED CODE of the BFT original remote control, using a pin, press the rear hide button (see the
picture) or, according to the new references, press the 1 and 2 buttons until the original remote control LED switches
on. (see the picture)
7. Now the WHY-EP LED will change the flash mode (more fast), for a reconfirmation of the correct code learning. This
step may take some seconds.
8. At this moment, press the WHY-EP button when you want to store the code and retain pressed until the WHY-EP LED
switches o.
9. Activate now the procedure to insert the new remote control on the receiver.
BFT
To activate the remote control on the receiver for models marked with proceed as below:
1. First of all you must be closed to the automation.
2. Press and retain pressed the programmed button during 10 seconds, when the LED start to flash, release the button.
3. Wait until the LED will turn o. The operation has been done, now you can use your new remote control.
To activate on the receiver all the other models: Refer you to the instructions of the original model.
NOTE: THE SEED CODE OF THE WHY-EP CAM BE EMITTED AS HERE BELOW:
1. Press the buttons 1 and 2 simultaneously for 8 seconds and release them when the LED start to flash;
2. While the LED is flashing press the button with the seed code needed.
ATTENTION!! Every kind of receiver can have the “radio-mode” disarmed. In this cases will be necessary insert the new remotes controls with the “manual procedures”.
V2
433 - 868
1. While pressing the button 1 of the “WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHY-EP LED will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown
in the picture).
4. Press and retain pressed the button to be programmed of the original remote control, till the LED will switch on as a
fix light; now release the button.
5. The WHY-EP LED will emit a short flash every 2 seconds. That it informs the user that, to duplicate the remote
control, it is necessary to emit the SEED CODE to realize the copy.
6. Transmit now the SEED CODE of the V2 original remote control pressing at the same time 1 and 2 buttons.
7. Now the WHY-EP LED will change the flash mode (more fast), for a reconfirmation of the correct code learning. This
step may take some seconds.
8. At this moment, press the WHY-EP button when you want to store the code and retain pressed until the WHY-EP LED
switches o.
9. Activate now the procedure to insert the new remote control on the receiver.

6
WHY-EP
Attention: verify the programming remote control is a MASTER.
Pressing whatever button, the LED has to emit a double flash rather than to switch on as a fixed light.
1. While pressing the button 1 of the “WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHY-EP LED will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance.
4. Press and retain pressed the button to be programmed of the original remote control, till the LED will switch on as a
fix light; now release the button.
5. The WHY-EP LED will emit a short flash every 2 seconds. That it informs the user that, to duplicate the remote
control, it is necessary to emit the SEED CODE to realize the copy.
6. Predispose the FAAC/GENIUS remote control for the SEED CODE emission. Press at the same time the 1 and 2 buttons
(note: THESE ARE THE BUTTONS OF THE DIAGONAL LINE as in the picture).
7. While FAAC/GENIUS remote control LED flashes, place it in front of WHY-EP at a distance of 5cm and press the button
to be programmed until the WHY-EP LED will change the flash mode (more fast), for a reconfirmation of the correct
code learning. This step may take some seconds.
8. At this moment, press the button when you want to store the code and retain pressed until the WHY-EP LED, switches
o.
9. The copy has been happened with success. Now check on the automation the correct functioning of new WHY-EP
remote control pressing two times the copied button.
Notes:
• If the LED flashes only 3 times and switches o, the code has not learnt correctly. Please repeat the operation from
the step 1.
• The WHY-EP memory is completely re-writable.
• To duplicate further buttons of WHY-EP, please repeat the operation from the step 1.
ROLLING COMPLEX
DUPLICATING PROCEDURES
FAAC
433 - 868 GENIUS
433 - 868

7
WHY-EP WHY-EP WHY-EP
DUPLICATING PROCEDURES
1. While pressing the button 1 of the “NEW WHY-EP”, at the same time press 4 times the 2 button.
2. Release both buttons. Now the LED of “NEW WHY-EP” will emit a short flash every 2 seconds.
3. Place the “SOURCE WHY-EP” in front of the “NEW WHY-EP” , at about 5 cm of distance (as in the picture 3 at the page 3).
4. Press and retain pressed the button to be programmed of the “SOURCE WHY-EP”
NOW IF THE CODE IN THE “SOURCE WHY-EP”
Notes:
• If the LED flashes only 3 times and switches o, the code has not learnt correctly. Please repeat the operation from the step 1.
• The WHY-EP memory is completely re-writable.
• To duplicate further buttons of WHY-EP, please repeat the operation from the step 1.
IS A FIXED
OR ROLLING-SIMPLE CODE
5a wait for a change flash (as a faster flash) of “NEW
WHY-EP” LED and a change of its color that confirms the
correct learning of code. This operation may take some
seconds.
6a While the LED is flashing, press the button of the
“NEW WHY-EP” where you want to program the code
just learnt, and retain pressed until the LED will switch
o.
7a The copy has been happened with success. Now
check on the automation the correct functioning of
NEW WHY-EP remote control pressing directly the
button where the code has been programmed. If it will
not work, please proceed with the insertion on the
receiver of the NEW WHY-EP, through the function,
if it is present, or through the procedures given by the
automation manufacturer.
IS A ROLLING-COMPLEX CODE
5b The WHY-EP LED will emit a short flash every 2
seconds. That it informs the user that, to duplicate the
remote control, it is necessary to emit the SEED CODE to
realize the copy.
6b Transmit now the SEED CODE of the “SOURCE
WHY-EP” pressing at the same time 1 and 2 buttons
for 3 seconds till the switch on of LED. While the LED
is flashing, (within 10 seconds) pressing and retain
pressed the button where you want to program the
SEED CODE.
7b Now the LED of the “NEW WHY-EP” will change
the flash (more fast) and color to confirm the correct
learning of the code. This step may take some seconds.
8b At this moment, press the NEW WHY-EP button when
you want to store the code and retain pressed until the
WHY-EP LED, switches o.
9b The copy has been happened with success. Now
check on the automation the correct functioning of
NEW WHY-EP remote control pressing directly the
button where the code has been programmed. If it will
not work, please proceed with the insertion on the
receiver of the NEW WHY-EP, through the function,
if it is present, or through the procedures given by the
automation manufacturer.

8
SPECIAL PROCEDURES
TO REACTIVATE THE ROLLING SICE TECH CODE INSERTED AS DEFAULT ON A
BUTTON, PROCEED AS HERE BELOW:
1. While pressing the button 1 of the WHY-EP, at the same time press 4 times the 2 button.
2. Release both buttons. Now the WHITE LED “WHY-EP” will emit a short flash every 2 seconds.
3. Press the button where you want to reactivate the rolling code and retain pressed till the LED switches o.
NOTES:
TO reactivate further buttons of WHY-EP, please repeat the operation form the step 1.
TO MAINTAIN THE SAME SERIAL NUMBER OF A ROLLING REMOTE
1. While pressing the button 2 of the WHY-EP, at the same time press 4 times the 2 button.
2. Release both buttons. Now the LED “WHY-EP” will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown in
the picture at the page 3).
4. Press and retain pressed the 1 button of the original remote control and wait for a change of color of “WHY-EP” LED
that it will switch o.
5. Choice the button where you want to program the freqeucny and press it. This step may take some seconds.
6. The copy has been happened.
7. Activate now the correct procedure for the copied model and insert the new remote control on the receiver (see the
compatibility list present in this manual).
8. Repeat this procedure for the other buttons, if necessary.
PROGRAM A ROLLING CODE ON EACH BUTTON WITH A SERIAL NUMBER
1. While pressing the button 4 of the WHY-EP, at the same time press 4 times the 1 button.
2. Release both buttons. Now the LED “WHY-EP” will emit a short flash every 2 seconds.
3. Place the original remote control to be programmed in front of the “WHY-EP”, at about 5 cm of distance (as shown in
the picture at the page 3).
4. Press and retain pressed the 1 button of the original remote control switches o.
5. Choice the button where you want to program the freqeucny and press it. This step may take some seconds.
6. The copy has been happened.
7. Activate now the correct procedure for the copied model and insert the new remote control on the receiver (see the
compatibility list present in this manual).
WHY-EP

9
WHY-EP COMPATIBILITY LIST
LEGEND:
BRAND MODEL D.O.R.
DOR TECHNOLOGY ACT ON THE RECEIVER DIRECT FUNCTIONING
ACM TX2, TX2 COLOR, TX4
ADYX TE4433H BLUE, 433-HG BRAVO
AERF
COMPACT, HY-DOM, MERCURI B,
MERCURI C, SABUTON, MARS,
SATURN, ST3/N, TERRA, TMP-1,
TMP-2, UNITECH
ALLMATIC BROWN, BROWN RED, BRO.OVER,
PASS, MINIPASS, TECH3
APERIO GO, GO PRO, GO MINI
APERTO (Sommer) 4020-TX03-434, TX02-434-2,
TX02-868-2
APRIMATIC TR, TM4, TXM
ATA PTX4 BLU, PTX4 PINK
AVIDSEN 104251, 104250, 104250 OLD,
104250 RED, 104257, 104350, 654250
BALLAN FM400, FM400E
BENINCA
TO. GO. WV, TWV, ROLLKEY, APPLE,
LOT WCV, CUPIDO, TO.GO. QV
IO
BFT
MITTO, MITTO M, MITTO RCB,
MITTO A, TRC, GHIBLI, MURALE,
KLEIO
CARDIN
TRQ S449,
TRQ S449 GREEN (PRECODE),
TXQ S449, TXQ S449 GREEN,
TRQ S486, TXQ S486, S437 TX,
XRADO

10
WHY-EP COMPATIBILITY LIST
BRAND MODEL D.O.R.
CASALI GENIUS/CASALI A252RC
CHAMBERLAIN/LIFT MASTER/
MOTOR LIFT
953ESTD, 371 LM, 971
LM, 84330E, 94334CE,
94333E/94334E/94335E, 9747E,
1A5639-7, 1A5477, 1A6487, 132B2372,
94330EML/9333EML/94335EML,
84330EML/84333EML/84335EML,
8747EML
CLEMSA
MUTANCODE, T, T-8, E-CODE N
MASTERCODE MV
ATTENTION! FIXED CODE
DASPI ZERO RC
DEA SYSTEM PUNTO 278, GOLDR, GENIE R 273,
GENIE R-GT2N, MIO TR, GT2M, TRN
DITEC BIXLP, GOL4, BIXLG
DOORHAN TRANSMITTER 4
DOORMATIC MILENY, MILENY-EVO
ECOSTAR RSC, RSE, RSZ
ERREKA
IRIS, ROLLER 2, ROLLER 433, ROLLER
868, SOL433, SOL868, VEGA 433,
VEGA 868
FAAC
TML 433SLH, DL 868 SLH,
XT 868 SLH, XT 433 SLH, T 868 SLH,
T 433 SLH, XT 868 SLH BLACK,
XT 433 SLH BLACK
XT 433 RC, TE433HG, XT4 433 RCBE
FADINI JUBI-SMALL, JUBI 433
GENIE GITR-3, GIT, GICT390, GIFT390-1,
G3T-BX, G1T-BX, GM3T, GICTD, GIFTD

11
WHY-EP COMPATIBILITY LIST
BRAND MODEL D.O.R.
GENIUS
AMIGOLD, AMIGO, KILO
BRAVO, ECHO
GIBIDI AU1600, AU1600 WOOD, AU1680,
AU1680 WOOD, DOMINO
JCM
NEO, TWIN
GO, GO PORTIS, GO NORTON,
KBLUE ETH-TEL01
KEY 900TXB-42R, TXB 44R, SUB 44R
KING GATES CLIPPER, STYLO
KLING KUA, KUA E, KUA S
LABEL SPYCO
LIFE FIDO
LINEAR
MCT-11, ACT-21, ACT-22,
STING RAY ACT-31,
STING RAY ACT-34B
MERLIN 2.0 E945M, E943M, E940M
MERLIN/PROLIFT C945, C940, C943, M842, M844
MHOUSE TX3, TX4, GTX4
MOOVO MT4G
NICE
SMILO, FLOR-S, VERY-VR,
FLOR-S ERA
ONE (ON), ON ERA, INTI, ERGO,
PLANO, ONE (ON FM)

12
WHY-EP
BRAND MODEL D.O.R.
COMPATIBILITY LIST
NORTON
NEO, TXCD
GO NORTON,
GO MINI NORTON
NOVOFERM
MCHS, MICRO-NOVOTRON 502,
MINI-NOVOTRON 504,
MICRO-NOVOTRON 502,
MICRO-NOVOTRON 504,
MICRO-NOVOTRON 31,
MICRO-NOVOTRON 51,
MINI-NOVOTRON 30,
MINI-NOVOTRON 50, MNHS,
O&O TX, T.COM R4-2, T.COM R8-2, TWIN,
TX (NEO)
PECCININ TX MENBRANA
PRASTEL MTE, MPSTLE, MPSTP2E, TCE, BFOR,
TRQ-P, SLIM-E
PUJOL
WARNING
YOU MIGHT FACE CUSTOMISED
CODES NOT DUPLICABLE
TWIN, VARIO, VARIO MARS,
VARIO OCEAN, NEO
RIB LITHIO
ROPER
NEO
GO ROPER, GO MINI ROPER
SABUTOM BROOVER, BROSTAR
SEA
HEAD, SMART DUAL ROLL,
SMART-3 ROLLING CODE,
COCCINELLA ROLL
SEAV BE HAPPY RS
SECULUX NEO
SILVELOX Mhz 2007, QUARZ SAW

13
WHY-EP
BRAND MODEL D.O.R.
COMPATIBILITY LIST
SIMINOR
CVXNL, MITTO
SIM433
SOMFY
K-EASY, K-EASY NEW, K-EASY OLD,
MITTO, KEY GO RTS, TELIS RTS,
KEYTIS RTS, KEYTIS RTS NS, ALARMA
SOMMER
4010, 4011, 4014 TX03-434-2,
4013 TX03-434-4, 4020 TX03-868-4,
4026 TX03-868-2, 4022 TX02-434-2,
4025 TX02-868-2, 4031 TX08-868-4
STAGNOLI KALLISTO, VENUS AV223
TAU 250K-SLIMRP, 250K-SLIMR,
250T-4RP
TELCOMA FM400E, FM400
TOR LIFT TORMIT4
V2 TSC, TXC, TRC, HANDY,
PHOENIX, PHOX 433
VDS ECO-R, TRQ P

DEDICATED TO
PROFESSIONALS
Sede Legale / Legal Headquarter
Via Berardo Maggi, 4 - 25124 Brescia (BS)
[phone]
[phone]
Sede Operativa / Operative Headquarter
Via Nedo Nadi, 7/A - 43122 Parma (PR)
why-pro.com