Wido ICE2 User manual

- 1 -
INSTRUCTION MANUAL
ICE MAKER
ICE2
Thanks for your choosing our ICE MAKER
Please read this Instruction Manual carefully before operation
Please keep it in a safe place and refer to it when necessary.

- 2 -
Description
1. Top Lid
7. Icefull sensor
2. Control panel
8. Fan cover
3. Sliding door
9. Water out
4. Ice storage tank
10. Water inlet
5. Fan
11.Power cord
6. Evaporator
Specifications
Model
ZB-250
Ice Making Capacity
40kgs
Ice Sizes
adjustable
Ice Storage Capacity
10kgs
Dimension
457*432*744
Voltage
AC 220-240V/50Hz
Power cord
3 pins grounded plug. (to reduce risk of electric shock)
Spare Parts
No.
Description
Picture
Quantity
1
Filter Bracket
option
2
Anti-drain Plug
1
3
Filter Connector
option

- 3 -
4
Adaptor
1
5
Water Follow
Controller
1
6
Filling Water
Pipe(1m)
1
7
Filling Water
Pipe(40cm)
1
8
Ice Scoop
1
9
Filter Bracket
2
Function
Instant making ice
Ice full alarming,add water water alarming
Crystalline ice in square
Before/First Use of Your Ice Maker
1.During transportation, the incline angle of the cabinet should not be over 45° .Do not turn the
Ice maker upside down.As this may damage the compressor and sealed system.
2.Remove all packing material and carefully check your ice maker to ensure it is in good
condition and that there is no damage to the ice maker or power cord and plug.
3The ice maker should be placed horizontally on a level surface.To ensure proper ventilation for
your ice maker allow 150mm of space at the top, the back and on each side. Do not install
the Ice maker near an oven, radiator, or any other heat source.
4.Before using the Ice maker for the first time, please wait 2 hours after positioning it, and keep
the front lid open for at least 2hours
5.Ensure that the voltage indicated on the ice maker corresponds with the voltage in your home.
6.Pure water is not allowed to be used on this unit, spring water is recommended.
Control Panel Operation

- 4 -
Area
Mark
Description
Indicators
ADD WATER
alert ice is not enough,need to check the water supply
TIMER
timer is working or time is under setting.
ICE
unit is under ice making process
ICEFULL
alert ice is full,need to be taken out
CLEAN
unit is under auto clean process.
LED screen
Buttons
button to change time setting
ON/OFF
turn on/off the unit
TIMER/CLEAN
set timer function or turn on auto clean function
Operating Instructions
Step 1 Fill water
onnect the external water pipe at back of unit with the water tape as follows.
Step 1.1
Insert filter bracket into the
hole at back of the unit or
assemble the filter bracket
onto back of the unit with a
thread
Step 1.2
Take off the film of the
filter,and take off the covers
at both side

- 5 -
Step 1.3
Thread the filter connectors
to two sides of the connector
Step 1.4
Push the filter into the filter
bracket,make sure the flow
direction on filter is from left
to right
Step 1.5
Connect filling pipes at both
side of the filter,before
connecting the pipe to the
unit,please let the water flow
over the filter for several
seconds till the water come
out is clean
Step 1.6
Well assemble the water
filling controller and the metal
parts as right sketch
Step 1.7
Connect water filling
pipe(1m) to the water filling
controller

- 6 -
Step 1.8
Connect water filling
controller and metal parts to
water faucet as right sketch
Step 1.9
Put a barrel beside the
unit,and then turn on the
water filling controller to let
the water flow over the filter
for 30seconds,till the water
from left side is clean
Step 1.10
Take off the anti-drain plug
from back of the unit, then
connect water pipe left to the
inlet hole(the left one)
Step 1.11
Insert the water filling
pipe(1m) to the drain hole(the
right one)
Step 1.12
If you need to take off the
pipe or replace it,please do
as follows:
Firstly take off the blue ring
named asA,then press the
white ring at the outer side
named as B,At last take out
the pipe
Step 2 Plug in.
Step 3 Timer setting: before press button ON/OFF, press button TIMER/CLEAN,the indicator

- 7 -
TIMER will light up,press button + or - to adjust the timer waken up time.If the timer function is
set,the indicator will light up
Step 4 Press button ON/OFF,unit starts to make ice,LED screen will show ambient
temperature
Step 5 Adjustment of ice making time: You can change the ice size by adjust the ice making
time as follow,at the last 10minutes before ice harvest,the LED screen will flash,press + or - to
adjust the ice making time for next cycles. One press of button +,data 1 will be shown on the
screen,and the ice making time for next cycles will be one minutes more.
For example,if LED flashes 10,at this time,you press button +,data 1 will be shon on the
screen,means next cycles,the ice harvest will count down from 11minutes. If two press is
done,then count down from 12minutes.
Step 6 Auto clean function: before the unit is turned on,long press the TIMER/CLEAN button
for 3seconds,unit will enter the auto clean mode.
Step 7 Press button ON/OFF again to turn unit off.
Caring
1.Clean the inner liner, water box, ice shovel and evaporator frequently. When cleaning, unplug
the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the
inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or
diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
2.Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of
obstruction. Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
3.If the machine is reused after a long time , maybe the water pump cannot pump sufficient
water due to the air inside, the ADD WATER water indicator light will turn on in this case . To
correct this press the START button again, then the machine will work normally.
4.To ensure the cleanliness of the ice cubes, water in the water reservoir should be replaced
every 24 hours.
5.If the compressor stops for any reason such as water shortage, too much Ice, power off, etc...
Do not start the system right away, wait 3 minutes, and then re-start the Ice maker.
6.Always change with fresh water before starting ice production at initial installation or after long
shut-off periods.
Troubleshooting
1. Please note, if the water filled to the evaporator is not symmetrical, small sundries maybe be
formed and lodged in the pipe which will mean that water will be filled to the evaporator causing
it to jam.
2. Please pull out the cap of the pipe, then let the water through the pipe in order to clean the
pipe, then you can replace the cap. It will make formal ice cubes
Problem
Possible Cause
Suggested Solutions
The compressor works
abnormally with a
Buzzing
noise
The voltage is lower
than recommended
Stop the Ice maker and do not restart
until the voltage is normal.

- 8 -
The light of ADD WATER
is on
There is no water or
water is not enough
Press the “STOP” button, fill with
water, and press the “START” button
again to restart.
Indicator light on the
display is not on
1.Control panel wire
line is loosen
2.Control panel is
broken
Call for service
The water is flowing,ice
is made,however no
release of ice
Temperature sensors
are connected by
mitake
Call for service
Everything is correct but
no ice is made.
1.Refrigerant leaks
2.Cooling system
blocked
call for service
WARNING
If the power cord is damaged; it must be replaced by the manufacturer, its service agent or a
similarly qualified person in order to avoid a hazard.
Fill with potable water only.
It is normal for the compressor and condenser surface to reach temperatures between 70°C and
90°C during operation and surrounding areas may be very hot.
Due to fast freezing, ice cubes may appear “Cloudy”. This is air trapped in the water and will
not affect quality or taste of ice.
This appliance can be used by children aged from 8years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision
Do not immerse in water
R-134a is a fluorinated greenhouse gas covered by the Kyoto Protocol,its global warming
potential is 1300.Please keep the unit well.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled waste disposal,recycle it responsibly to promote the
sustainable reuse of material resources.

- 9 -
Safety Notes
•Position the ice maker on flat, stable surface.
•This ice maker can only be used indoors.
•The installation and any repairs of the ice maker should be performed by qualified
technician.
•If the power cord is damaged; it must be replaced by a qualified person to avoid a
hazard.
•Do not immerse this product in water or use a jest washer to clean the unit.
•Do not cover this appliance when it is operating.
•Only use drinking or potable water with this appliance.
•This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
•Children shall not play with the appliance.
•Cleaning and user maintenance shall not be made by children without supervision
•Please keep all packaging material away from children and pets.
•