wildkin Rocking Horse User manual

Page 1 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
Thank you for purchasing this Rocking Horse! We know
that it will bring you and your little one years of
enjoyment! Please first be sure you have all the
necessary components listed on page 2. We suggest
that you lay them all out on the carpet before
assembling. If for any reason you think a component
may be missing, please contact our customer service
team. Please read the General Safety Instructions
below before beginning assembly.
General Safety Instructions
- Your Rocking Horse is safety tested for all ages, however, it is recommended that the chair only be used by
children under 100 lbs.
- Please do not let children kneel or stand in the chair. It was designed for sitting and rocking only.
- Please do not let young children “over-rock” the chair because it may tip over.
- Each part of this rocking horse is individually wrapped in plastic. Plastic bags can be dangerous to young children.
To avoid the danger of suffocation, keep these bags away from babies and small children.
- This piece must be assembled by an adult. Please do not leave any spare parts near children.
Tools You Will Need
- Standard Phillips Head Screwdriver. CAUTION: It is highly recommended that you not use power tools or electric
screwdrivers as screws should not be over-tightened.
Care Instructions:
- We recommend this item be wiped down with a non-bleach wipe. However, if there are fabric cushions on your
rocking horse, we strongly recommend that these be dry-cleaned only.
Rocking Horse Assembly Instructions
ADULT ASSEMBLY REQUIRED.
SMALL PARTS AND SHARP POINTS MAY BE PRESENT PRIOR TO ASSEMBLY.
KEEP OUT OF BABY’S REACH.
WARNING:

Components
A 1- Front Leg
Page 2 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
Rocking Horse Assembly Instructions
BL 1- H-shaped Left Leg BR 1- H-shaped Right Leg
C1- Wooden SeatH 1- Rocker
D 1- Chair Back
* Please note that the shape of your
chair back (D) and horizontal leg
support (A) may be slightly different
than the drawing.
* Please note left and right arm rest are labeled as if
you were sitting in the chair. “Bump” of the arm rest
should be facing out.
FrontFront
F 1- Pony Head G 2- Handles
EL 1- Left Arm Rest ER 1- Right Arm Rest

C
D
Components
Page 3 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
Rocking Horse Assembly Instructions
w1 2- Lg. Washer (1 ”)
Hardware Shown in Actual Size
1
4
s3 8- Sm. Machine Screw (1”)
s2 4- Med. Machine Screw (1 ”)
1
4
s1 2- Lg. Machine Screw (1 ”)
3
4
w2 2- Med. Washer ( ”)
3
4
w3 12- Sm. Washer ( ”)
5
8
w4 14- Spring Washer ( ”)
3
8
1. Place Seat (C) level to the ground.
2. Insert Chair Back (D) vertically into the pre-drilled
holes on Seat (C).
Figure 1
Attach Chair Back (D) to Seat (C).

C
C
C
A
BL
BR
D
EL
ER
Page 4 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
10. Insert Front Leg (A) to the bottom of the Seat
(C).
11. Put Small Washer (w3), Spring Washer (w4) and
Small Machine Screw (s3) in sequence into the
pre-drilled holes to secure Front Leg (A) to Seat
Bottom (C).
5. Insert Lg Machine Screw (s1) through Spring
Washer (w4) and Sm. Washer (w3) into pre-drilled
hole. (As shown in drawing).
3. Insert Arm Rests (EL & ER) vertically into the
pre-drilled holes on Seat (C).
4. Align Arm Rests (EL & ER) to the pre-drilled holes
on the Chair Back (D) post.
6. Secure screw with screwdriver until tight. Repeat
process for both legs.
7. Turn assembly upside down and align Rear Leg
(BR & BL) to the bottom of the Seat (C).
8. Insert Sm. Machine Screw (s3) through Spring
Washer (w4) and Small Washer (w3) through Rear
Legs and then into pre-drilled hole on the Seat (C).
9. Insert Med. Machine Screw (s2), through Spring
Washer (w4), through Med. Washer (w2), through
Large Washer (w1) into pre-drilled holes to secure
Rear Legs (BR & BL) to the Seat (C).
Rocking Horse Assembly Instructions
Figure 2
Attach Arm Rest (EL & ER) to Chair Back (D).
Attach Rear Legs (BR & BL) to the bottom of Seat (C). Figure 3
Attach Front Leg (A) to Seat (C).
Figure 4
w3 w4 s1
w3
w4
s3
w3
w4
s3
w3 w4 s1

F
C
C
A
H
BL
BR
14. Insert Rear Legs (BR & BL) and Front Leg (A)
to Rocker (H).
15. Place Rocker (H) upside down.
16. Insert Small Machine Screw (s3) through Spring
Washer (w4), through Small Washer (w3) into the
pre-drilled holes on Rocker (H) to secure to the
rest of the assembly. Screw in until secure.
Page 5 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
Rocking Horse Assembly Instructions
13. Insert Medium Machine Screw (s2) through
Spring Washer (w4), through Small Washer (w3)
into both pre-drilled holes on the sides of Seat
(C) and screw them in until secure.
Figure 5
Attach Pony Head (F) to the front of the Seat (C).
Secure Pony Head (F). Figure 6
Attach Assembly to Rocker (H).
Figure 7
12. Insert Pony Head (F) into the pre-drilled holes
of the front of the Seat (C).
w3
w4
s2
w3
w4
s3
w3
w4
s3
w3
w4
s2
w3
w4
s3

C
G
G
F
Page 6 of 6
P: 866-727-0544 E: [email protected] www.wildkin.com
Rocking Horse Assembly Instructions
Figure 8
Secure Handle (G) to Pony Head (F).
17. Align Handle (G) with Pony Head (F) and turn
handle to screw in until secure.