Williams-Sonoma MERCER CONSOLE User manual


Date:8‐Dec‐15www.williams‐sonoma.comPage1of6
Rev: 
























MERCER CONSOLE







Date:8‐Dec‐15www.williams‐sonoma.comPage2of6
Rev: 
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Parts Included:
(A) Top 1x
(B) Shelf 1x
(C) Leg 4x
(D) Leg 2x
(E) Rail 2x
(F) Connector 4x
Hardware Included:
(G)
Glass Bumper
10 x
(H)
Bolt
Dia.1/4” x 5/8”
32x
(I)
Allen Wrench
1 x
B
D
A
D
C
E
F


Date:8‐Dec‐15www.williams‐sonoma.comPage3of6
Rev: 
Assembly Instruction Steps:
1. Attach 2 Legs (C) to the Connector (F) as shown. Insert Bolt (H) and tighten withAllen Wrench (I).
2. Attach Leg (D) to assembly as shown, insert Bolt (H) and tighten withAllen Wrench (I). Repeat step 1 and 2 to
have 2 sets of leg assembly.
I
H
C
D
2X
2
X
H F
I
C
F
4
X


Date:8‐Dec‐15www.williams‐sonoma.comPage4of6
Rev: 
3. Attach Rails (E) to the leg assembly as shown, insert Bolt (H) and tighten with Allen Wrench (I).
4. Place the console base to the desired position.
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the furniture wobbles,
determine which corner does not touch the ground correctly. With two people follow these steps:
1) Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
2) Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and check
stability.
3) Repeat steps until furniture sits firmly on the ground.
H
E
I
E
4
X


Date:8‐Dec‐15www.williams‐sonoma.comPage5of6
Rev: 
5. Place the Glass Bumper (G) onto the base as shown.
6. Carefully place the Shelf (B) onto the position as shown.
G
G
6
X
4
X
B


Date:8‐Dec‐15www.williams‐sonoma.comPage6of6
Rev: 
7. Gently lift Top (A) and place onto the top as shown. Ensure the Top is centered.Assembly is complete!
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
For glass tops and shelves, glass cleaner may be used, but avoid spraying it onto the metal or ceramic
frame.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores|catalog
A