Willow Milk Container User manual

reuse, refill, rejoice!
Willow Wearable Breast Pump Milk Container Quick Start Guide

For complete Instructions for Use, visit willowpump.com

3
Cap Dial
Locking Ring
Spout
Tab
ContainerInsert
meet your milk container
Your Milk Container comes assembled, but has two parts - the Insert and Container.
Tunnel
Locked Position
Unlocked Position
Pour Spout Interior Valve
TopBackFront
Dial
Air Vent
(underneath Dial)

4
set dial to 1 to pump...
Rotate Dial so only the 1 is visible (and the 2 is hidden under Cap).
Rotate all the
way until
the Dial stops!
‘1’ = Pump
• Set Dial to 1 (Pump
position) at the start of
your session
• This keeps the air vent
open when you pump
TIP: The air vent is open while you pump.
See page 9 for tips to avoid leaks.

5
...and 2 when you’re done!
Rotate Dial so only the 2 is visible (and the 1 is hidden under Cap).
Rotate all the
way until
the Dial stops!
‘2’ = Flip to Finish
• Set Dial to 2 (Flip
to Finish position)
when you’re finished
pumping
• This closes the air
vent for Flip to Finish
• NOTE: If Dial is in
the wrong position
during Flip to Finish,
milk will leak from
the air vent

6
sterilize for first-time use
1. Disassemble Milk Container
2. Boil Container and Insert for ten minutes to sterilize before you use it
(just for the rst time!). Place on a clean surface to air dry.
Peel back
Cap
Rotate blue
locking ring to
unlocked position
1Push hard on Insert
tunnel (use both thumbs!)
until it pops out
2Separate
Container and
Insert
3 4
DO NOT put Container or Insert in a microwave or microwave sterilizer bag.

7
Insert Flextube™Container Pump
get ready to pump
Just 4 parts - and you’re ready to pump!

8
assemble container &insert
Press firmly to
seal to Container
2
Place Insert into
Container (tab facing up)
1Rotate to
locked position
3Make sure
Cap is closed
4

9
Rotate Dial so only
the 1 is visible (and the
2 is under Cap)
7
Connect Flextube™ tip
to Insert spout.
Push tip all the way down!
5Push Flextube™
collar in so it sits firmly
against Cap
6

10
align and attach pump
For more on alignment, pumping, and breaking latch, visit:
willowpump.com for Willow Wearable Breast Pump Instructions for Use
Center your nipple in
the Insert tunnel.
Turn Pump on and bring straight on to
Milk Container with your other hand to
connect. Press Play to initiate latch.
21

11
Watch videos in app or
at willowpump.com
pumping tips (stay dry!)
• The air vent (on the top
of the Milk Container) is
open while you pump.
• To avoid leaks, make sure
milk doesn’t cover the air
vent when you pump.
• To pump in any position,
pump with our spill-proof
Milk Bags.
Get up
and pump...
!...but don’t lean
too far forward
or back

12
finished pumping?set dial to 2...
Pause Pump, then rotate Dial to
2 (Flip to Finish position) to close
air vent - or milk will leak!
1
Break latch and
remove Pump
2
Rotate so Cap
faces you
3
TIP: Rotate Dial to 2 (Flip to Finish position) before you
remove Willow from your bra to avoid spills.

13
then flip to finish
Watch videos in app or
at willowpump.com
FLIP all the way over and wait
until gulps stop (a total of 8 gulps)
6
TILT until pump
starts to gulp
4
HOLD until
milk disappears
from tunnel
5

14
time to transfer!
Always keep Container and Insert assembled to pour.
1Flip Pump over so
Milk Container faces up
2Separate Milk
Container from Pump
4Pour from pour
spout on top
3
Open Cap

15
disassemble to clean
Separate Flextube™ from Milk Container to clean, then follow instructions
on p. 4 to disassemble into parts below.
CAUTION: Do not remove Dial, locking ring, or interior valve to clean.
For cleaning instructions for your Flextube™ and Pump, visit:
willowpump.com for Willow Wearable Breast Pump Instructions for Use
Insert CapContainer TIP: You can leave the
Cap on or remove it
to clean. Make sure
the Cap is open if you
leave it on.

16
keep your milk container clean
❏Rinse immediately under running water for at least 1 minute.
❏Soak in warm, soapy water for a minimum of 5 minutes (use mild
dishwashing soap, and agitate while they soak).
❏Use the Large Cleaning Brush from your Willow Pump Kit to clean
(wash for at least 60 seconds, minimum 30 seconds of brushing).
Use the Small Cleaning Brush to clean the Insert spout.
❏Rinse with hot water for at least 50 seconds.
❏Place parts on clean paper towels or a drying rack to air dry.
After each use, wash your Container and Insert in the dishwasher
(top rack only) or follow the instructions below!
See any signs of milk after cleaning? Repeat the steps above.

17
!Scrub around
interior valve -
don’t push a brush
through it!

18
For more information on Willow’s lights, visit:
willowpump.com for Willow Wearable Breast Pump Instructions for Use
milk container alerts & lights
Willow’s lights tell you what’s going on with your Milk Container. Here’s what they mean.
White Solid:
Your Container is full. Flip
to Finish (see p. 10-11),
transfer to a bottle or bag,
then press Pump/Pause
to continue pumping.

pump wherever life takes you.
[e-mail]
willowpump.com/help
1-888-WILLOW-3

ART-1084-A
©2019 Willow. All rights reserved. Willow and Flextube are trademarks or
registered trademarks of Willow in the United States and other countries.