Wilson Electronics WPCM-2 User manual

Before you begin:
It is advised to have the assembled unit
mounted to the ceiling by a professional. It would be helpful to
have two people assemble the unit.
Although this unit is designed to hold up to 300 lbs, it is
imperative that the fi nished unit is mounted securely to the
ceiling. Ceiling installation hardware must be determined
on an individual basis and therefore is NOT included.
This item ships in three boxes. All three boxes contain bagged
hardware.
Instructions for a WPMSS are included. Please do not follow
those instructions but you may fi nd the parts diagrams helpful.
Qty
Description
Part
1
Ceiling Mount Bracket
M
1
Pole
P
2
Upright Bracket A (see diagram)
A
2
Upright Bracket B (see diagram)
B
2
Center Brackets
C
4
TV Brackets
D
4
Arms for 10 degree Tilt
T
4
Stud Straps
S
2
“U” Channel Brackets
U
18
1⁄4” Screws
18
Washers
8
3” Screws & Washers
4
3” Wood Stud Phillips Head Screws
4
Small Washers
1
Tube Plug
2
Plastic Collars
1
Mounting Pole Pin
1
Mounting Pole Cap
1
Set Screw (10/32 x 1⁄4”)
1
3/8 x 2.5” long Hex Head Bolt
1
Nylock Nut for 3/8 x 2.5” Bolt
8
Nylock Nuts 5/16 for stud straps
WPCM-2 Dual Monitor Ceiling Mount
H. Wilson Company 555 West Taft Drive South Holland, IL 60473
Phone [phone] E-mail [email protected]om
Instructions:
1.
Remove all items from boxes and identify all parts.
2.
Review these instructions completely before proceeding.
3.
Make sure that Parts A & B are oriented in the same
direction as the diagrams for A & B. Attach Part A to Part B
using (2) 1⁄4” screws at the bottom of the mount by inserting
the screws from the outside through the hole on the fl ange into
the weld nut. (***See Part B diagram of WPMSS Instructions)
**** If you are not using the 10° tilt, proceed to Step 5. ****
4.
Repeat steps 3 for second pair of brackets. Set one pair
aside.
5.
Determine which of the three height options to use and
attach both Parts U to Part P using the silver 2 1⁄2” long bolt and
Nylock nut. Tighten. Place black tube plug into the bottom (end
with no hole) of Part P.
Stud Straps
Stud Straps
Stud Straps
Stud Straps
Part ‘T’
AA
B
B
B
A
Pole
‘U’ Channel
Brackets
Part ‘T’
Large Silver Bolt attaches
Large Silver Bolt attaches
U Channel brackets to pole
U Channel brackets to pole
Photo A
Photo B

6.
Place two stud straps through holes on part A of fi rst bracket pair and attach fi rst
bracket pair to pole assembly using washers and Nylock nuts.
7.
Place two stud straps through part A of second bracket pair and thread through other
side of pole assembly making sure to allow enough room to place washers and nuts. Tighten
second bracket assembly to pole assembly.
8
. Determine whether you are utilizing the 10° tilt.
a.
If you are NOT using the tilt feature, close the bracket assemblies and fasten the tops
together using the 1⁄4” screws.
b
. If you are utilizing tilt, Attach Part T to the top of Part A using (2) 1⁄4” screws, by
inserting the screws from the outside through hole on fl ange into weld nut on the arm.
Repeat on other side. Close the bracket assemblies & fasten the tops using 1/4” screws.
9.
Place plastic collars into the top and bottom of receiving tube on Part M.
10.
Place the pole assembly with A & B brackets attached upright and insert the top of the
pole through the receiving tube on Part M (ceiling mount bracket).
11.
Push the Mounting Pole Pin (located in bagged hardware) through the hole in the top
of the Pole assembly. Place Mounting Pole Cap over Pin and pole being sure it seats fi rmly.
***At this point you may want to “dry fi t” Part C into part B to familiarize yourself
with the hanging mechanism. ***
12.
Attach parts D – fl at side down - to back of each TV using hardware specifi c to your TV.
(Hardware not included for this step.)
13.
Attach part C with the fl at side down and the notch oriented at the top to parts D using
(2) two 1⁄4” screws and washers for each TV.
14.
Install the completed ceiling mount assembly to the ceiling using the appropriate hard-
ware and method for your particular needs.
15.
With the WPCM-2 properly and safely installed to the ceiling, hang each TV by aligning
Part C with the receiving tabs on Part B and gently lower into the bracket assembly.
16.
Insert security screw into top of Part C, securing it to B.
17.
Determine that the assembly is at the desirable position and tighten the set screw
located near the bottom of the receiving tube on the ceiling mount bracket.
Pole assembly is the
pole & channel brackets
Secure stud
straps & pole
assembly
Photo C
Pole assembly with TV Bracket
attached - side view