Wincomm WPC-765 User manual

WPC-765/WPC-765E
Mini PC
USER’S MANUAL
P/N: 205G000WPC7650, V1.0
Copyright© ,2013. All rights reserved
All other brand names are registered trademarks of their respective owners.
The information contained in this document is subject to change without notice

WPC-765/WPC-765E User’s manual
ii
Version Change History
Date
Version
Description
Remark
2014/01/21
1.0
First release
Cosa Huang

WPC-765/WPC-765E User’s manual
iii
Acknowledgments
Intel® 3rd generation Core i and Celeron are registered
trademarks of Intel® Corporation.
IBM, PC/AT, PS/2 are trademarks of International Business
Machines Corporation.
Microsoft® Windows is a registered trademark of Microsoft®
Corporation.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
C&T is a trademark of Chips and Technologies, Inc.
UMC is a trademark of United Microelectronics Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
VIA is a trademark of VIA Technology, Inc.
Award is a registered trademark of Award Software
International, Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel is a trademark or registered trademark of Intel
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of
their respective owners.

WPC-765/WPC-765E User’s manual
iv
FCC Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment.
This equipment generates, uses and can radiate radio frequency energy. If
not installed and used in accordance with this user manual, it may cause
harmful interference to radio communications.
Note that even when this equipment is installed and used in accordance
with this user manual, there is still no guarantee that interference will not
occur. If this equipment is believed to be causing harmful interference to
radio or television reception, this can be determined by turning the
equipment on and off. If interference is occurring, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to a power outlet on a circuit different from
that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Warning:
Any changes or modifications made to the equipment which are
not expressly approved by the relevant standards authority could
void your authority to operate the equipment.
To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
Do not modify this equipment without authorization of the
manufacturer.

WPC-765/WPC-765E User’s manual
v
Safety Instructions
Intended use
The WPC-765/765E is intended to serve as a mini PC which is
designed for general purpose for hospital environment. It shall
not be used for life-supporting system.
Greeting & Setup
Thank you for purchasing the WPC-765/WPC-765E unit. We wish
that this unit will be durable and reliable in providing your
medical application needs. Please follow the instructions below to
ensure the unit continues to have high performance.
Unpacking
After opening the carton, there will be a mini PC unit with an
accessory box. Examine the contents to see if there are damages
to the unit and if all accessories are present.
Setting up
Please read this manual carefully and remember to keep this
manual for future reference.
Safety Instructions & Cleaning
The unit has undergone various tests in order to comply with
safety standards. Inappropriate use of the open frame unit may
be dangerous. Please remember to follow the instructions below
to insure your safety during the installation and operating
process.
Transporting & Placement of unit
1. When moving the unit on a cart; be very cautious. Quick
stops, excessive forces and uneven surfaces may cause
the cart to overturn thus risking the unit to fall to the
ground.
2. If the mini PC unit does fall to the ground, immediately
turn the power off and disconnect cords. Then contact a
service technician for repairs. Continual use of the unit
may result cause a fire or electric shock. Also, do not repair
the unit on your own.

WPC-765/WPC-765E User’s manual
vi
3. Having two or more people transporting the display unit is
recommended. In addition, when installing the unit by
suspending it also requires two or more people.
4. Before suspending the unit, make sure the material used
for suspension is sturdy and stable. If not properly
suspended, the display unit may fall and cause serious
injury to people standing nearby as well as to the unit
itself.
5. If you wish to mount the display unit, remember to use
only the mounting hardware recommended by the
manufacturer.
Electrical and Power Source Related
1. This mini PC unit must operate on a power source as
shown on the specification label. If you are not sure what
type of power supply used in the area, consult your dealer
or local power supplier.
2. The power cords must not be damaged. Applied pressure,
added heat, and tugging may damage the power cord.
3. The power cord must be routed properly when setup takes
place. We advise that this aspect measure is to prevent
people from stepping on the cords or while the unit is
suspended to prevent flying objects from getting tangled
with the unit.
4. Do not overload the AC outlets or extension cords.
Electrical shocks or fires may occur from overloading.
5. Do not touch the power source during a thunderstorm.
6. If your hands are wet, do not touch the plug.
7. Use your thumb and index finger, grip firmly on the power
cord to disconnect from the electrical socket. By pulling the
power cord, may result in damaging it.
8. If the unit is not going to be in use for an extended period
of time, remember to disconnect the unit.
9. Please use only the power cord provided by the dealer to
ensure safety and EMC compliance.
Various Factors of Environment

WPC-765/WPC-765E User’s manual
vii
1. Do not insert objects into the openings.
2. Do not have liquids seep into the internal areas of the mini
PC unit.
3. Having liquids seep in or inserting objects into the unit
may result in electric shocks from taking and/or short
circuiting the internal parts.
4. Do not place the mini PC unit in the presence of high
moisture areas.
5. Do not install the mini PC unit in a wet environment.
6. Do not place near unit near heat generating sources.
7. Do not place the unit in a location where it will come in
contact with fumes or steam.
8. Remember to keep the mini PC unit away from the
presence of dust.
9. If water has flow in or seep in, immediately disconnect the
open frame unit. Then contact a service technician for
repairs.
Ventilation Spacing
1. Do not cover or block the openings on the top and back
sides of the display unit. Inadequate ventilation may cause
overheating thus reducing the lifespan of the unit.
2. Unless proper ventilation is present, do not place unit in an
enclosed area; such as a built-in shelf. Keep a minimum
distance of 10 cm between the display unit and wall.

WPC-765/WPC-765E User’s manual
viii
Cleaning the unit
1. Remember to turn off the power source and to unplug the
cord from the outlet before cleaning the unit.
2. Carefully dismount the unit or bring the unit down from
suspension to clean.
3. Please use a dry soft cloth to clean the unit.
4. Take a dry cloth and wipe the unit dry. Remember to avoid
having liquids seep into the internal components and areas
of the mini PC unit.
Servicing, Repairing, Maintenance & Safety Checks
1. If the unit is not functioning properly, observe the
performance level of the display closely to determine what
type of servicing is needed.
2. Do not attempt to repair the mini PC unit on your own.
Disassembling the cover exposes users’ to high voltages
and other dangerous conditions. Notify and request a
qualified service technician for servicing the unit.
3. To avoid risk of electric shock, this equipment must only be
connected to a supply mains with protective earth.
4. If any of the following situations occur turn the power
source off and unplug the unit. Then contact a qualified
service technician.
(a) A liquid was spilled on the unit or objects have fallen
into the unit.
(b) The unit is soaked with liquids.
(c) The unit is dropped or damaged.
(d) If smoke or strange odor is flowing out of the operating
unit.
(e) If the power cord or plug is damaged.
(f) When the functions of the unit are dysfunctional.
5. When replacement parts are needed for the mini PC unit,
make sure service technicians use replacement parts
specified by the manufacturer, or those with the same
characteristics and performance as the original parts. If

WPC-765/WPC-765E User’s manual
ix
unauthorized parts are used it may result in starting a fire,
electrical shock and/or other dangers.
ISO 7000-0434: Caution, consult ACCOMPANYING
DOCUMENTS.
ISO 7000-1641: Follow operating instructions or
Consult instructions for use.
IEC 60417 -5009: STAND-BY.
IEC 60417-5031: Direct current.
EU-wide legislation, as implemented in each
Member State, requires that waste electrical and
electronic products carrying the mark (left) must be
disposed of separately from normal household
waste. This includes monitors and electrical
accessories, such as signal cables or power cords.
When you need to dispose of your display products,
please follow the guidance of your local authority, or
ask the shop where you purchased the product, or if
applicable, follow any agreements made between
yourself.
The mark on electrical and electronic products only
applies to the current European Union Member
States.

WPC-765/WPC-765E User’s manual
x
When networking with electrical devices, the operator is
responsible for ensuring that the resulting system meets the
requirements set forth by the following standards:
–EN 60601-1 (IEC 60601-1)
Medical electrical equipment
Part 1: General requirements for safety
–EN 60601-1-1 (IEC 60601-1-1)
Medical electrical equipment
Part 1-1: General requirements for safety
Collateral standard: Safety requirements for
Medical electrical systems
–EN 60601-1-2 (IEC 60601-1-2)
Medical electrical equipment
Part 1-2: General requirements for safety
Collateral standard: Electromagnetic compatibility;
Requirements and tests
Accessory equipment connected to
the analog and digital interfaces
must be in compliance with the
respective nationally harmonized
IEC standards (i.e. IEC 60950 for
data processing equipment, IEC
60065 for video equipment, IEC
61010-1 for laboratory equipment,
and IEC 60601-1 for medical
equipment.) Furthermore all configurations shall comply with the
system standard IEC 60601-1-1. Everybody who connects
additional equipment to the signal input part or signal output part
configures a medical system, and is therefore, responsible that
the system complies with the requirements of the system
standard IEC 60601-1-1. The unit is for exclusive interconnection
with IEC 60601-1 certified equipment in the patient environment
and IEC 60XXX certified equipment outside of the patient
environment. If in doubt, consult the technical services
department or your local representative.

WPC-765/WPC-765E User’s manual
xi
Caution:
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW
-20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE
EQUIPMENT.
The user is not to touch SIP/SOPs and the patient at the same
time.
The sound pressure level at the operator’s position according to
IEC 704-1:1982 is no more than 70dB (A).
A) Grounding reliability can only be achieved when the equipment
is connected to an equivalent receptacle marked “Hospital
Only” or “Hospital Grade”.
B) Use a power cord that matches the voltage of the power outlet,
which has been approved and complies with the safety
standard of your particular country.
C) Caution: This adapter Sinpro MPU101-105 is a forming part of
the medical device
Contact information:
3F, No.14, Prosperity Road II, Science-Based Industrial Park,
Hsinchu, Taiwan 300, R.O.C
TEL: [phone]
E-Mail: [email protected]

WPC-765/WPC-765E User’s manual
xii
Table of Contents
Acknowledgments........................................................iii
FCC Class B ....................................................................iv
Safety Instructions.......................................................v
Introduction .........................................................1
Product Description......................................................1
Package list .....................................................................2
Features ...........................................................................3
Specifications .................................................................4
Guidance and manufacturer’s declaration –
electromagnetic emissions.....................................6
Guidance and manufacturer’s declaration –
electromagnetic immunity.......................................7
Guidance and manufacturer’s declaration –
electromagnetic immunity.......................................9
Immunity.............................................................................9
Cleaning/Disinfecting.................................................11
Getting Started ..................................................12
System Set Up.............................................................12
Dimension......................................................................13
System View.................................................................15
Disconnect Device ......................................................17
B. Scrap Computer Recycling.................................18

WPC-765/WPC-765E User’s manual
1
Introduction
Product Description
The WPC-765 / WPC-765E Mini PC are based on Intel 3rd
generation Core i processor which can deliver faster graphic with
higher CPU performance. It accommodates one 2.5” SATA III
hard disk drive and up to 8GB DDR3 SODIMM.
Fanless solution, integrated multimedia functions and extensive
expansion options make them the perfect platform upon which to
build comprehensive lifestyle computing applications.
The WPC-765/WPC-765E is compact, Giga LAN and selectable
WLAN network compatible PC with full safety and medical
approval and features to control a dedicated system with a wide
variety of applications. Combining the WPC-765/WPC-765E into
your system can achieve both cost-saving and efficient
improvements.
Common applications include Surgical, Radiology, PACS (Picture
Archiving Communication Systems), LIS (Lab Information
Systems) and Electronic Medical Record. The WPC-765 /
WPC-765E are definitely your perfect choices.

WPC-765/WPC-765E User’s manual
2
Package list
Before you begin installing your Medical Station, please make
sure that the following items have been shipped:
The WPC-765 or WPC-765E Mini PC unit
One DVD containing user manual, chipset drivers
Power Adapter x 1 (Mf:Sinpro, type/model: MPU101-105)
Power cord –Hospital grade used(US type), or other type in
UK, EU…etc.

WPC-765/WPC-765E User’s manual
3
Features

Intel 3rd Generation (Iv y Bridge) Core i7/i5/i3 CPU
True Fanless design for 0°C~40°C operating temp
Medical 60601-1 3rd edition certification
Rugged SECC/aluminum metal enclosure
Rich COM ports for control applications
Mini PCI-e sockets for WLAN & other add-on expansions
16 GB maximum memory for dual channel DDR3 SODIMM
Flexible customization for specific application requests

WPC-765/WPC-765E User’s manual
4
Specifications
[
Hardware Specifications
CPU
Support
Support Ivy bridge Intel® Core™ i7 i5/i3 rPGA
Socket Type Processor (35W max.)
-Core™ i7-3632QM (6M Cache, 2.20 GHz)
-Core™ i5-3210M (3M Cache, 2.50 GHz)
-Core™ i3-3110M (3M Cache, 2.40 GHz)
Chipset
Intel® HM76 PCH
BIOS
4Mb AMI Flash BIOS
VGA
Intel® integrated HD Graphics 4000 by Ivy bridge
CPU
Audio
Realtek ALC262 Audio Codec, 2+2 watts power
amplifier
LAN
Marvell 88E8071 Giga LAN x 2
Memory
Two 1066/1333/1600 MHz DDR3 SODIMM socket
support dual Channel, non-ECC, up to 16GB
IO
EC
Serial ATA
SATA3, 300 MB/s transfer rate x 1
WDT
Generates system reset; 256 segments, 0, 1,
2…255 sec/min.
Storage
HDD
2.5” SATA HDD drive bay x 1
Expansion slots
PCI-E
PCI-E x 16 expansion slot x 1 (Generation 3.0)
Mini-PCIe
52 pin card-edge type compatible to PCI
Express*Base specification 2.0 x 1
+3.3V loaded 0.75A+0.25A=1A
+1.5V loaded 0.375A
External I/O
USB
USB 2.0 x 2, USB 3.0 x 2
COM
RS232 x 5, RS232/RS422/RS485 x 1
LAN
RJ-45 x 2 (Gigabit Ethernet)
Audio
3.5mm phone jack connector * 2 (line-out, and
mic-in)

WPC-765/WPC-765E User’s manual
5
Video
output
DVI-D x 1 , or DVI-D x1 + CRT x1 (option, via Y
cable)
Power Adapter
Power
Close
MFR
Sinpro
Type
MPU101-105
Input Voltage
AC 100 ~240 V, 1.25 –0.5A @47 ~63 Hz
Output Voltage
DC 12V @8.33A
MTBF
100,000 hrs operation at 25 ℃
Mechanical Specifications
Architecture
Aluminum heatsink and SECC with black
coating
Color
Black
Mounting / Holder
Bracket mounting mechanism
Dimension (WxHxD)
WPC-765 : 294.6 * 188 * 61 mm
WPC-765E : 294.6 * 188 * 96.2 mm
Net Weight
WPC-765: 3kg (w/o power adapter)
WPC-765E: 3.8kg (w/o power adapter)
Packing Filler
PE
Environmental Specifications
Temperature
Operating: 0°C to 40°C (32°F ~104°F)
Storage, Transportation: -20°C to 60°C (-4°F
~140°F)
Humidity
Operating:
10% to 90%@ 40°C, non-condensing
Storage, Transportation:
10% to 90%, non-condensing
Vibration
Operating: 15g/0.53 oz, 11 ms, half sine wave
Non-operating: 50g/1.76 oz, 11 ms, half sine
wave
Shock
Operating: 5 ~ 17 Hz ,
Amplitude：0.117 ~ 500Hz ,
Acceleration：1.0G
Non-operating:10~55Hz/0.15g, 55~500Hz/2.0g
Altitudes
Operational: up to 3000 m (9842 feet)
Shipping: up to 12192 m (40000 feet)

WPC-765/WPC-765E User’s manual
6
Pressure
700 –1060 hPa (Operation)
186 –1060 hPa (Storage)
186 –1060 hPa (Transportation)
Guidance and manufacturer’s declaration – electromagnetic
emissions
The model WPC-765/WPC-765E is intended for use in the
electromagnetic environment specified below. The customer or the user
of the model WPC-765/WPC-765E should assure that it is used in such
an environment.
Emissions test
Compliance
Electromagnetic environment –
guidance
RF emissions
CISPR 11
The model WPC-765/WPC-765E
uses RF energy only for its internal
function. Therefore, its RF emissions
are very low and are not likely to
cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11
The model WPC-765/WPC-765E is
suitable for use in all establishments,
including domestic establishments
and those directly connected to the
public low-voltage power supply
network that supplies buildings used
for domestic purposes.
Harmonic
emissions
IEC 61000-3-2
Voltage
fluctuations/
flicker emissions
IEC 61000-3-3
Recommended separation distances between
portable and mobile RF communications equipment and the model
WPC-765/WPC-765E
The model WPC-765/WPC-765E is intended for use in an
electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of the model WPC-765/WPC-765E
can help prevent electromagnetic interference by maintaining a minimum
distance between portable and mobile RF communications equipment
(transmitters) and the model WPC-765/WPC-765E as recommended
below, according to the maximum output power of the communications
equipment.

WPC-765/WPC-765E User’s manual
7
Rated maximum
output power of
transmitter
W
Separation distance according to
frequency of transmitter
m
150 kHz to
80 MHz
d = 1,2
80 MHz to
800 MHz
d = 1,2
800 MHz to
2,5 GHz
d = 2,3
0,01
0,12
0,12
0,23
0,1
0,38
0,38
0,73
1
1,2
1,2
2,3
10
3,8
3,8
7,3
100
12
12
23
For transmitters rated at a maximum output power not listed above, the
recommended separation distanced in meters (m) can be estimated
using the equation applicable to the frequency of the transmitter, where P
is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.
NOTE 1At 80 MHz and 800 MHz, the separation distance for the higher
frequency range applies.
NOTE 2 These guidelines may not applyin all situations. Electromagnetic
propagation is affected by absorption and reflection from structures,
objects and people.
Guidance and manufacturer’s declaration – electromagnetic immunity
The model WPC-765/WPC-765E is intended for use in the electromagnetic
environment specified below. The customer or the user of the model
WPC-765/WPC-765E should assure that it is used in such an environment.
Immunity
test
IEC 60601
test level
Compliance
level
Electromagnetic
environment –
guidance
Electrostatic
discharge
(ESD)
IEC
61000-4-2
6 kV
contact
8 kV air
6 kV
contact
8 kV air
Floors should be wood,
concrete or ceramic tile. If
floors are covered with
synthetic material, the relative
humidity should be at least 30
%.

WPC-765/WPC-765E User’s manual
8
Electrical fast
transient/burst
IEC
61000-4-4
2 kV for
power
supply lines
1 kV for
input/output
lines
2 kV for
power
supply lines
1 kV for
input/output
lines
Mains power qualityshould be
that of a typical commercial or
hospital environment.
Surge
IEC
61000-4-5
1 kV
line(s) to
line(s)
2 kV
line(s) to
earth
1 kV line(s)
to line(s)
2 kV line(s)
to earth
Mains power qualityshould be
that of a typical commercial or
hospital environment.
interruptions
and
voltage
variations
on power
supply
input lines
IEC
61000-4-11
<5 % UT
(>95 % dip
in UT)
for 0,5 cycle
40 % UT
(60 % dip in
UT)
for 5 cycles
70 % UT
(30 % dip in
UT)
for 25
cycles
<5 % UT
(>95 % dip
in UT)
for 5 sec
<5 % UT
(>95 % dip in
UT)
for 0,5 cycle
40 % UT
(60 % dip in
UT)
for 5 cycles
70 % UT
(30 % dip in
UT)
for 25 cycles
<5 % UT
(>95 % dip in
UT)
for 5 sec
Mains power qualityshould be
that of a typical commercial or
hospital environment. If the
user of the model
WPC-765/WPC-765Erequire
s continued operation during
power
mains interruptions, it is
recommended that the model
WPC-765/WPC-765E be
powered from an
uninterruptible power supply
or a battery.