Wincor Nixdorf iCASH 15 Configuration guide

iCASH 15 Cleaning Instruction
Edition November 2010

All product names mentioned in this document are registered trademarks.
Copyright ©Wincor Nixdorf International GmbH, 2010
All rights including the rights to the translation, reprinting, transmission or copying by any means, in whole or in part are
reserved. Offenders will be liable for damages. All rights including rights resulting from a patent grant or registration of a utility
or design are reserved.

iCASH 15 – Cleaning Instruction
1
General Informations
The device must be switched off for service and maintenance work.
You should service and clean the parts of the device listed below at the specified intervals.
In addition, please note the following:
Take care not to drop any cleaning liquids into the device.
Only use the cleaning material listed in this manual. Do not use thinners.
Information where to order the listed cleaning materials is given in the chapter "Cleaning materials".
Maintenance
Check the dust box once a day and empty it if necessary.
Perform a visual inspection of the coin hoppers and coin paths.
Clean the coin paths.
Cleaning the housing
Cleaning interval: as needed
Cleaning material: Wet cleaning cloths
for stainless steel surfaces Ballistol oil for cleaning stainless steel
for varnished surfaces Wincor Nixdorf cleaning set
for plastic surfaces Wincor Nixdorf cleaning set
Cleaning the coin paths
The conveyer belts must not come into contact with alcohol.
Clean the coin paths with compressed air.
Cleaning interval: when necessary, at least once a month
Cleaning material: Wincor Nixdorf air duster
Cleaning the coin validator
Clean the coin validator with cleaning swabs.
Cleaning interval: when necessary, at least once a month
Cleaning material: Cleaning swabs
Except for the Coin Validator all components of the iCASH 15E must be cleaned
and maintained by trained and authorized Service personnel only! Unauthorized or
inexpert cleaning or maintenance will invalidate your warranty and liability protection.

iCash 15 – Cleaning Instruction
2
Coin Validator (User and Service Staff)
Unlock the iCASH 15 (1) and pull out the unit (2).
Swing the front cover open (1).
2
1
2
2

iCASH 15 – Cleaning Instruction
3
Unlock the green levers (arrows) and open the cover to the right.
i
Always use a commercially available hard toothbrush to clean the device. Finally, clean the
area with a slightly moistened (Isopropylalkohol) cloth and then dry it.
To clean the whole area (shaded area) turn the green wheel (1) to bring the rotor (2) to a different
position. Pay special attention to the thickly white marked area (3).
Mount the device in logically reverse order.
2
3
1

iCash 15 – Cleaning Instruction
4
Conveyer Belt (Service Staff only)
Start the software application to run the conveyer belt. Start deposite and cover the light
barriers with your cleaning cloth to start running the conveyer belt.
Clean the running conveyer belt
with a wet cloth. The liquid must not
contain alcohol!
Never use spray.
Clean the light barrier sensors from
dirt and dust with compressed air.
Find 6 holes (sensors inside, 3 on
each side (see arrows).
Conveyer belt

iCASH 15 – Cleaning Instruction
5
Coin Conveyer Sensors (Service Staff only)
Unlock the iCASH 15 (1) and pull out the unit (2).
Swing the front cover open (1).
1
1
2
2

iCash 15 – Cleaning Instruction
6
Unlock the green levers (arrows) and open the cover to the right.
While holding the cover open, press the coin conveyer unit lockings carefully to the right and to
the left (see arrows) and open the device.
i
Never use a knife, a scissor or any other sharp objects to clean the device!
Press here to the left
Press here to the right

iCASH 15 – Cleaning Instruction
7
Clean the light barrier sensors using a cotton bud moistened with Isopropylalcohol.
The
conveyer belts
must not come into contact with alcoholic solutions.
After cleaning close the coin conveyer belt housing and the coin validator with the green lever.
Close the device.

iCash 15 – Cleaning Instruction
8
Hopper Sensor (Service Staff only)
Unlock the iCASH 15 (1) and pull out the unit (2).
Swing the front cover open (1).
1
1
22

iCASH 15 – Cleaning Instruction
9
Unlock the unit (1) and swing it upwards to the stop (2).
Remove all hoppers to clean the sensor (1) with a cloth moistened with Isopropylalcohol.
Set the hoppers back in place.
1
2
1

iCash 15 – Cleaning Instruction
10
Push the green lever and close the unit.

iCASH 15 – Cleaning Instruction
11
Approved Cleaning Materials
The items listed below can be ordered from Wincor Nixdorf branch office or your Wincor Nixdorf sales
partner.
Product Name Order Number Explanations
Professionell cleaning set for
EDP devices
100ml plastic cleaner in a pump
bottle
50 dust cloths
10 keyboard swabs for places
difficult to reach
01750097335 For cleaning and maintaining keyboards
and varnished and plastic-coated hous-
ing
Damp cleaning cloths
Dispenser box with 100 cloths
01750097332 Alcohol-based aqueous diluted solution
for cleaning and maintaining delicate
EDP devices, keyboards and housing.
Not suitable for cleaning conveyer belts!
Dry cleaning cloths
Antistatic and fluff free
(Pack with 300 cloths)
01750097334 For cleaning display panes
Compressed air spray
PRESSAIR
400ml bottle without a valve,
70cm hose
01750097331 Cleaned compressed air, FCKW-free,
for removing loose dust and dirt
particles.
Cloth with ISOPROPYL 1000
pieces 01750104065 Pure isopropyl alcohol for cleaning coin validator and display. Not suitable for
cleaning conveyer belts!
Cleaning card 01750016388 For cleaning magnetic heads and chip
contacts in ID card readers
Please note the manufacturer’s specifications on the packaging and on the information sheet included
in the packaging. The product may be damaged or soiled if materials are used that are not approved
or if they are used improperly.

Wincor Nixdorf International GmbH
D-33094 Paderborn
Order No.:01750206779A