Winmate T4-series User manual

T4 series Panel PC User Guide
I
T4-series Panel PC
VIA Eden Mini-ITX Fanless SBC, Low
Power Design with VIA Platform, TFT
LCD and 10/100/1000 base-T
Ethernet.
User Guide Version 1.0

T4 series Panel PC User Guide
II
FCC Statement
This device complies with part 15 FCC rules. Operation is subject to
the following two conditions：
zThis device may not cause harmful interference.
zThis device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class "a"
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at him
own expense.

T4 series Panel PC User Guide
III
Copyright Notice
Copyright © 2007 Winmate Technology Inc., ALL RIGHTS RESERVED. No part of
this document may be reproduced, copied, translated, or transmitted in any form or by
any means, electronic or mechanical, for any purpose, without the prior written
permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
Disclaimer
Winmate Communication Inc. reserves the right to make changes, without notice, to
any product, including circuits and/or software described or contained in this manual
in order to improve design and/or performance. Winmate Communication assumes no
responsibility or liability for the use of the described product(s), conveys no license or
title under any patent, copyright, or masks work rights to these products, and makes
no representations or warranties that these products are free from patent, copyright, or
mask work right infringement, unless otherwise specified. Applications that are
described in this manual are for illustration purposes only. Winmate Communication
Inc. makes no representation or warranty that such application will be suitable for the
specified use without further testing or modification.
Warranty
Winmate warrants that each of its products will be free from material and
workmanship defects for a period of one year from the invoice date. If the customer
discovers a defect, Winmate will, at its option, repair or replace the defective product
at no charge to the customer, provided it is returned during the warranty period of one
year, with transportation charges prepaid. The returned product must be properly
packaged in it’s original packaging to obtain warranty service.
If the serial number and the product shipping data differ by over 30 days, the
in-warranty service will be made according to the shipping date. In the serial numbers
the third and fourth two digits give the year of manufacture, and the fifth digit means
the month (e. g., with Afor October, B for November and C for December).
For example, the serial number 1W07Axxxxxxxx means October of year 2007.

T4 series Panel PC User Guide
IV
Check List
Before using this Panel PC, please make sure that all the items listed below
are present in your package
¾1 x T4 series Panel PC
¾1 x T4 series Panel PC User Guide
¾1 x V170 SBC User Manual
¾1 x Power adapter
¾1 x Power cord
¾1 x CD with Driver Utility and User's Manual
¾1 x Touch Driver CD (Optional)
¾Mounting of screws (Option)
Make sure that all of the items listed above are present. Do not attempt to
apply power to the system if there is damage to any of its components.
Customer Service
We provide service guide for any problem as follow steps：First, visit the website at
http://www.winmate.com to find the update information about the product. Second,
contact with your distributor, sales representative, or our customer service center for
technical support if you need additional assistance. You may have the following
information ready before you call：
¾Product serial number
¾Peripheral attachments
¾Software (OS, version, application software, etc.)
¾Description of complete problem
¾The exact wording of any error messages
In addition, free technical support is available from our engineers every business day.
We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products. Please do not
hesitate to call or e-mail us.
Notice
1. Do not touch the LCD panel surface with sharp or hard objects.
2. Do not use abrasive cleaners, waxes or solvents for cleaning, use only a dry
or damp, soft cloth.
3. Use only with a high quality, safety-approved, AC/DC power adapter.

T4 series Panel PC User Guide
V
Safety Precautions
Warning!
Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections
while the power is on. Sensitive electronic components can be
damaged by sudden power surges. Only experienced electronics
personnel should open the PC chassis.
Caution!
Always ground yourself to remove any static charge before
touching the CPU card. Modern electronic devices are very
sensitive to static electric charges. As a safety precaution, use a
grounding wrist strap at all times. Place all electronic components
in a static-dissipative surface or static-shielded bag when they are
not in the chassis.

T4 series Panel PC User Guide
VI
Safety and Warranty
1. Please read these safety instructions carefully.
2. Please keep this user's manual for later reference.
3. Please disconnect this equipment from any AC outlet before cleaning. Do not use
liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near the equipment
and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or electrical shock.
13. Never open the equipment. For safety reasons, only qualified service personnel
should open the equipment.
14. If any of the following situations arises, get the equipment checked by service
personnel:
A. The power cord or plug is damaged.
B. Liquid has penetrated into the equipment.
C. The equipment has been exposed to moisture.
D. The equipment does not work well, or you cannot get it to work according to
the user’s manual.
E. The equipment has been dropped and damaged.
F. The equipment has obvious signs of breakage.
15. Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -10°C (-14°F) or above 55°C (131° F). It may damage the
equipment.

T4 series Panel PC User Guide
VII
Revision History
Version Date Note Author
0.1 2007.10.19 9First Version Shawn
1.0 2007.11.19 9Initial Release Shawn

T4 series Panel PC User Guide
VIII
Contents
CHAPTER 1 GENERAL INFORMATION.........................................................................................1
1-1 Introduction .....................................................................................................1
1-2 V170 SBC and T4 series Panel PC System Specifications .............................2
1-3 LCD Selection Guide.......................................................................................3
CHAPTER 2 GETTING STARTED.....................................................................................................4
2-1 Input / Output Devices.....................................................................................4
2-2 Starting the Panel PC& O/S Installation..........................................................5
2-3 Driver Installation............................................................................................5
CHAPTER 3 TOUCH DRIVER INSTALLATION.............................................................................6
3-1 Introduction .....................................................................................................6
3-2 The ELOAccuTouch Driver Installation.........................................................7
3-2-1 Configuration Utility............................................................................8
3-3 The Premier Touch Driver Installation..........................................................10
3-3-1 Configuration Utility..........................................................................11
CHAPTER 4 T5 SERIES PANEL PC MOUNTING GUIDE...........................................................13
4-1 Open Frame Panel PC: ..................................................................................13
4-2 5mm Panel Mount Panel PC:.........................................................................15
4-3 10mm IP65 Panel PC.....................................................................................17
4-4 Chassis Panel PC...........................................................................................19
NOTICES..............................................................................................................................................20

T4 series Panel PC User Guide
1
Chapter 1 GENERAL INFORMATION
1-1 Introduction
The T4 series Panel PC is fanless, low power PC with VIA CX700 single
chipset combines with a TFT LCD Panel. The VIA Eden energy efficient
processor delivers the most performance per watt available in the market. The
Panel PC is designed to satisfy most of the applications in the industrial market,
such as POS, KIOSK, Industrial Automation, HMI and Programmable
Control System. It’s a PC-based system with DDR2 SDRAM, VGA/LCD
controller, four COM ports, and on-board 10/100/1000 Mpbs Base-T Ethernet.
The Panel PC supports one PCI expansion slot for extra applications, like
Wireless, Ethernet, COM port, VGA solutions. It is a compact design to meet
the demanding performance requirements of today’s business and industrial
applications.

T4 series Panel PC User Guide
2
1-2 V170 SBC and T4 series Panel PC System Specifications
System Specification
Processor VIA Eden™ 1.0GHz by EBGA Type
Chipset VIA CX700 Single Chipset
Memory Two DDR2 slots 240 pin Support up to 2GB DDR2 400 /
533 SDRAM
BIOS Award 4Mbit
Graphic Chipset Integrated VIA UniChrome™ Pro Integrated Graphics
Processor, Sharing memory architecture up to 64 MB
Ethernet Realtek 8110SBL LAN Controller (10/100/1000 Mb)
Audio VIAVT1708 HD Codec
USB 6 x USB ports, USB 2.0 compliant(2 x pin header)
Serial port 3 x RS232(1 x pin header), 1 x RS232/422/485 ports
Expansion Slot 1 x PCI slot
HDD 2.5” HDD for 8.4” ~ 12.1”
3.5” HDD for for 15” above
O/S(Optional) Windows XP Embedded / Windows XP Professional /
WinCE5.0 / Linux
Mechanical Specification
Construction Aluminum hosing
Mounting Open Frame/Chassis/Panel Mount/IP65/Rack Mount
Power Supply
Power input +24V DC-IN(4-Pin, Power Jack)
Power Consumption TBD
Environmental Specification
Operation Temperature 0~45°C
Operating Humidity 30%~90% ( non-condensing, RH )
Certificate CE, FCC