Wintal IR Repeater Kit User manual

IR Repeater Kit Instruction Manual
The IR Repeater Kit connects IR Connecting Block, IR Receiver, IR Emitter,
and Power Supply together to interface the IR system to the audio/video
components.
Related Components:
IR Connecting Block
& Mounting Screw x 2 pcs
IR Receiver
Dual IR Emitter
Single IR Emitter
In-Wall IR Receiver
Power Supply x1

IR Connecting Block
FEATURES
1. Six emitter output connections.
2. Convenient IR confirmation LED.
3. Status power receptacle with LED
indicator.
4. Power receptacle with LED indicator.
5. Three conductor 1/8” receptacle for inter-
facing with many brands of freestanding IR
receivers.
6. Large detachable IR receiver connection.
7. Compact size for mounting near audio
equipment.
SPECIFICATIONS
Dimensions: 82W x 60H x 27D mm
Weight : 110g
INSTRUCTIONS
○
1 Power
Connect a 12 VDC (200mA to 1A) power
supply to the power jack of the IR
Connecting Block. The red LED will be
illuminated when powered. This will power
all of the IR components connected to the
system. Depending on the type of
components and the number of components
will determine how much current the power
supply will need to provide.
○
2 Status Power
12VDC 200mA 2.1mm + Tip – sleeve.
Connect a power supply to this connection
will power the status connection. The green
LED will be illuminated. This can be from a
12 volt trigger output or from a wall type
power supply plugged into a switched outlet
of a stereo receiver. If you are using products
like the In-Wall IR Receiver that have a
status indicator, simply plug a 12 VDC power
supply into the switched outlet and when the
receiver is turned on the status LED will be
illuminated.
○
3 IR Receiver Connection
This is a three terminal 1/8” plug that is
common to many of the free standing IR
receivers. This will connect the power,
ground and signal. Signal is Tip, ground is
the ring and power is the sleeve.
○
4 In-Wall IR Receiver Connection
Connect the In-Wall IR Receiver to the
detachable connector labeled +12VDC,
GND, STATUS, and SIGNAL.
○
5 Emitter Outputs
Connect up to 6 emitters to the emitter jacks
labeled 1-6. Place the emitters on the source
equipment.
(Purchased separately)

IR Receiver
Features
1. CFL friendly–allows installations in areas with compact fluorescent lighting.
Works in most lighting environments.
2. Blue IR confirmation LED.
3. Wide band IR receives IR from many types of remotes.
4. Self-adhesive tape for quick and easy fixing on any flat surface.
5. 3 meters cable with 3.5mm stereo mini-plug.
Specifications
Receive Frequency Range…………………………..….34 kHz to 60 kHz
Transmit Frequencies……………………………..…….38 KHz & 56 KHz
Range……………………………………………….... …….40ft. @ 38 KHz
............................................................................. 25ft. @ 56 KHz
Power……………………………………………………12VDC, 30mA max.
Dimensions…………………………..………………45L x 14W x 13H mm
Cord Length……………………………..………………………….10ft (3m)
Connector Type…………………………..…..1/8” (3.5mm) TRS mini plug
Weight………………………………….....………………………………28 g
Wire connections

Dual IR Emitter
A. Standard installation
1. IR emitter attached directly to IR sensor
window.
2. Most reliable activation
B. Attach emitter on inside shelf
1. Attach emitter on shelf above or below IR
sensor.
2. Less reliable activation.
C. Cabinet with door installation
1. Attach emitter on door, round shape facing the IR
sensor.
2. Less reliable activation.
Note: Occasionally, more reliable activation can occur by moving the IR
emitter further away from the device. This may be due to improper placement
of the emitter, or that the sensor itself is partially obscured. It may also be due
to a peculiar remote control unit / sensor combination. Placing the emitter
5~10cm away from the IR sensor can achieve significantly better activation in
such cases. Please experiment to achieve optimal activation before securing
with the self-adhesive pads.