Wintop iDoorSensor User manual


Version0.21
QuickstartiDoorSensor U
Technicalspecs
Normaloperatingvoltage2xAAA1,5Vbatteries
FrequencyrangeϵϬ8.42MH z
WirelessRangeUpto30metersinlineofsight
BasicOperations
‐TheiDoorSensor canbe placedonanydoororwindow.
‐The iDoorSensor canreport the statusofthedoor(OPEN/CLOSED).
‐TheiDoorSensor canmeasurethetemperature.
‐TheiDoorSensor alsohas anexternalcontact.
Mounting
1. Useaflatscrewdriverattheinletsonthesidestogentlyunlockthebackcover.
2. Usethedesignatedholesonthebackcovertomountthe iDoorSensor.
3. PlacetwoAAA1,5Vbatteriesintothedevice.
4. Placethe iDoorSensor onto thebackcover,besuretocloseitonallsides
andthatthetampergetsthroughthebackcoveroftheiDoorSensor(indicationmode:
Tamperpressed/released).
5. After3secondsstartuproutinebegins(indicationmode:Readyforlearnmode).
6. After5moreseconds(8secondsintotal)mountingiscompleted.(indicationmode:Mounting
successful)
7. iDoorSensoris now ready to use.
8. Removethebackcoverofthemagnetandrepeatstep2and4withthemagnetformountingit.
IncludeorexcludeinZWavenetwork
1. MakesureyourZ‐Wavecontrollerisintherightoperationmode(includeorexclude).
2. Whenthe iDoorSensor is mounted,removeitfromthebackcoverasexplainedinsteponeofthe
Mountinginstructions.
3. Pressandholdthetamperswitchfor1secondandrelease to startthe inclusion orexclude process 
(indicationmode:Readyforlearnmode).
4. (TheproductwillstartNWIautomaticallyafterunsuccessfulnormalinclusion)
Indicationmode
Theindicatorlightgivesvariousstatusesofthedeviceasfollows:
1. Readyforlearnmode: indicatorlightblinkseverysecond.
2. Learninprogress(add):indicatorlight2timeseverysecond.
3. Learninprogress(remove):indicatorlight3timeseverysecond.
4. Learnmodesuccess: indicatorlightisonforonesecond.
5. Learnmodefailed: indicatorlightblinks8timesrapidly.
6. Tamperpressed/releasedindicatorlightblinks3timesrapidly.
7. Mountingsuccessful  indicatorlightisonfor1second.
Externalcontact
Magnet
IndicatorLight
Tamperswitch


Version0.21
TechnicalManual

Caution:
‐Thisdeviceisusingaradiosignalthatpassesthroughwalls,windowsanddoors.Therangeisstrongly
influencedbylocalconditionssuchaslargemetalobjects,housewiring,concrete,furniture,
refrigerators,microwavesandsimilaritems.Onaverage,theindoorrangeisapproximately30meters.
‐Donotexposethisproducttoexcessiveheatormoisture.
‐Preventlongtermexposuretodirectsunlight.
‐Donotattempttorepairthisproduct.Iftheproductisdamagedorifyouareindoubtaboutthe
properoperation,taketheproductbacktotheplaceofpurchase.
‐Donotcleantheproductwithanyliquid.
Technicaldetails







SupportingCommandClasses:

Basictype:BASIC_TYPE_ROUTING_SLAVE
Generictype:GENERIC_TYPE_SENSOR_BINARY
Specifictype:SPECIFIC_TYPE_NOT_USED
Listening:False,Z‐WaveLib:4.51

class:0x30COMMAND_CLASS_SENSOR_BINARY
class:0x70COMMAND_CLASS_CONFIGURATION
class:0x71COMMAND_CLASS_ALARM
class:0x72COMMAND_CLASS_MANUFACTURER_SPECIFIC
class:0x80COMMAND_CLASS_BATTERY
class:0x84COMMAND_CLASS_WAKE_UP
class:0x85COMMAND_CLASS_ASSOCIATION
class:0x86COMMAND_CLASS_VERSION
class:0x31COMMAND_CLASS_SENSOR_MULTILEVEL
class:0xEFCOMMAND_CLASS_MARK
class:0x20COMMAND_CLASS_BASIC
class:0x31COMMAND_CLASS_SENSOR_MULTILEVEL

NotlisteningRoutingSLAVE
Normaloperatingvoltage2xAAA1,5Vbatteries
From2,3to4,0Vdc
donotuserechargeablebatteries
FrequencyrangeϵϬ8.42MH z
WirelessRangeUpto30metersinlineofsight
Storagetemperature‐5°Cto+65°C
Storagehumidity10%to70%
Operatingtemperature0°Cto50°C
Operatinghumidity:30%to80%


Version0.21
ThisZ‐Waveproductwillbeusedasroutingslave.SlavenodesarenodesinaZ‐Wavenetworkthatreceive
commandsandperformactionsbasedonthecommand.Thisdevicewillalwaysbeinsleepmodebecauseit
worksonbatteries.Insleepmodethedeviceisnotactivelistening,thedevicewillwakeupaccordingtothe
wakeupcommandclass.

IncludeInitiator
TheincludeinitiatorisusedwhenPrimaryandInclusionControllersincludenodesintothenetwork.When
boththeincludeinitiatorhavebeenactivatedsimultaneouslythenewnodewillbeincludedtothenetwork(if
thenodewasnotincludedpreviously).
ExcludeInitiator
TheexcludeinitiatorisusedbyPrimaryControllerstoexcludenodesfromthenetwork.Whentheexclude
initiatorandaslaveinitiatorareactivatedsimultaneously,itwillresultintheslavebeingexcludedfromthe
network(andresettoNodeIDzero).Eveniftheslavewasnotpartofthenetworkitwillstillberesetbythis
action.
Z‐Wavecompatibility
BecausethisisaZ‐Wavedevice,itmeansitcanco‐operatewithotherZ‐Wavedevicesofothermanufacturers.
Itcanco‐existinaZ‐Wavenetworkexistingwithproductfromothermanufacturers.
Hops&Retries
TheZ‐Waverangehasarangeofupto30metersinlineofsight.Thissignalisnotlimitedtothe30meter
rangeduetoroutingtheZ‐Wavemessagetoothernodesinthenetwork.ThiswaytherangeoftheZ‐Wave
networkcanbeexpandedto150metersindoors(limitof4hops).

class:0x20COMMAND_CLASS_BASIC
Whenadoorisopenedabasicsetframewiththevalue255issenttotheassociatednodes.
Whenadoorisclosedabasicsetframewiththevalue0issenttotheassociatednodes.Thisisthecontrolling
roleofthebasiccommandclass.

Thesupportingroleofthebasiccommandclassismappedtothesensorbinarycommandclass.

class:0x25COMMAND_CLASS_SENSOR_BINARY
TheSensorBinaryCommandClasscanbeusedtocheckthestatusoftheDoorSensor(openorclosed).
Where“255”isopen,and“0”isclosed.

class:0x86COMMAND_CLASS_VERSION
ThisCommandClassisusedtoobtaininformationabouttheDoorSensor.TheZ‐Wavelibrarytype,theZ‐Wave
protocolversionandtheapplicationversionwillbereported.

class:0x72COMMAND_CLASS_MANUFACTURER_SPECIFIC
Thiswillreportinformationaboutthemanufacturer.ThisproductwillcontainthemanufacturerIDofWintop.
ManufacturerIDofWintopis 0x97,theID of this product is 0x82.

class:0x70COMMAND_CLASS_CONFIGURATION
Configureparameters:
0. notused
1. Settodefault
Description:  Setallconfigvaluestodefaultvalues(factorysettings).


Version0.21
ReadmoreinchapterConfigurationReset.
Size: 1byte*
Param1:  if0xFFthensettodefault
Param2,3,4:notused

2. Externalcontact 
Description:  Configurewhattheexternalcontactsendswhentrigger
Default:0x00(sendalarmreport)

Size:   1byte*
Param1:  if0x00:Sendaalarmreportwithtype2
If0x01‐0xFF:SendaBasicsetframetoallnodesinassociationgroup
2.
3. Notused
Description:Isnotusedbutstillcanbesetandrequested.
Size:   1byte*

4. Notused
Description:Isnotusedbutstillcanbesetandrequested.
Size:   1byte*

5. Themode
Description: theoperatingmode.
Default:0x01

Size:    1byte*
Param1:Mode1:Normaloperatingmode.
Mode3:Z‐Wavechipisalwaysontorequeste.g.versionor
manufacturerid.
Ifanymodeotherthen3,thatvaluewillbereportedafteragetbut
willbehandledinSWasmode1.
Param2,3:  notused.

6. Thetemperatureoffset
Description:  Aoffsetforthetemperature.
Default:0x00

Size:    2bytes*
Param1,2:  Asignedintegertodeterminetheoffsetoffthetemperature.
Param3,4:  notused

*ifasizeisotherthengivensizetheframeisignoredtotallysoconfigurationvaluesarenotchanged

class:0x85COMMAND_CLASS_ASSOCIATION
TheAssociationCommandClassisusedtoassociateotherdeviceswiththeDoorSensor.Thedevicesthatare
associatedcanbecontrolledonapplicationlevel.

TheDoorSensorcanbeassociatedintoagrouping.Ifso,theDoorSensorcancontrolotherZ‐Wavedevice(does
nothavetobeacontroller).


Numberofgroupings:2


Version0.21
Maximumsupportednodespergroup:5

Group1:iftheinternaldoorcontact(magnet)istriggereditsendsaZ‐Waveframetoeverynodeinthisgroup

Group2:iftheexternaldoorcontactistriggereditsendsaZ‐Waveframetoeverynodeinthisgroupifitis
configured(seeconfigurationdocumentationparam2:externalcontact).

Class:0x80COMMAND_CLASS_BATTERY
Thisclassisusedtorequestandreportbatterylevelsforagivendevice.
Whenbatterylevelislowerthen20%theDoorSensorwillsendabatterywarning(value255)aftereverywake
upnotification.Abatterygetwillreporttheactualvalueevenifbelow20%

class:0x84COMMAND_CLASS_WAKE_UP
TheWakeUpCommandClassisusedatbattery‐operateddevices.ThisclassallowstheDoorSensortowakeup
occasionallytonotifyothersdevices,thattheDoorSensorisreadytoreceivecommands.Afterreceivingthe
commandstheDoorSensorwillgointosleepmodeagain.Thewakeupintervalcanbesetusingthe
WAKE_UP_INTERVAL_SETcommand.

Thedefaultvalueis0x1C20=7200sec=2hour
Thedefaultnodeis0xFF=255(broadcast)

Itispossibletosendawakeupnotificationonuserinteraction.Todothispressandholdthetamperswitch
for8seconds.

Whenthewakeuptimeissetto0awakeupnotificationisneversendperiodically,onlyonuserinteraction.

class:0x31COMMAND_CLASS_SENSOR_MULTILEVEL
Sensor_multilevel_get
TheSensorMultilevelCommandClassisusedtogetareportfromtheDoorSensor.Thereturnedvalueisthe
measuredtemperatueinsidethehousingwith2decimals.

class:0x71COMMAND_CLASS_ALARM
Thiscommandclassisusedtoidentifythestateofthetamperalarm.Thedevicewillsendanunsolicitedreport
tothecontrollerifthestatusischanged,thevalue0x00willindicatethatthetamperisplacedcorrectlyonthe
wall.Thevalue0xFFwillindicateatamperalarm.
Thereare2differentalarmtypes:
2:Externaldoorcontact
3:Tamperswitch
Everyotheralarmtypethatisrequestedwillbeignoredbyapplication.


Version0.21

ConfigurationReset
TheDoorSensorSupportsaconfigurationresetsfunction.Configurationresetmeans
‐Allconfigurationvaluesaredefaulted.
‐Wakeupintervalisdefaulted.
‐Allassociationarecleared

Thisfunctioncanbeactivatedbysendingaconfigurationsetframe:

CONFIGURATION_SET
Parameter:0x01
Size: 0x01(can’tbedifferentfrom1)
Value: 0xFF(canbeanyvalueexceptfor0x55or0xAA)

Whenthevalueofconfigurationvalueisrequested2possiblevaluescanbereturned

CONFIGURATION_REPORT
Parameter:0x01
Value0x55:Devicedoesn’thaveallhisconfigurationsettingsanymore.
Evenwhenaconfigurationparameterischangedbacktothedefaultvalue
Value0xAA:Devicesstillhasallhisfactorysettings.
Thisareonlyconfigurationparameters,wakeupintervalcanbechanged.

Alwaysawakemode
Thealwaysawakemodeisusedtorequestdifferentvaluesfromthedevicee.g.versionandmanufacturer
specific.

Thealwaysawakemodecanbeactivatedby:

CONFIGURATION_SET
Parameter: 0x05
Size:  0x01(can’tbedifferentfrom1)
Value:  0x03(mode3)

Thealwaysawakemodecanbedeactivatedby:

CONFIGURATION_SET
Parameter: 0x05
Size:  0x01(can’tbedifferentfrom1)
Value:  Anyvalueexcept3

Asecondoptiontodeactivatemode3is
1. Removebatteries.
2. Waitca10seconds.
3. Replacebatteries

Note:inalwaysawakemodethebatterieswillbedrainveryfast,wedonotrecommendtousethismode.


Version0.21
Troubleshooting
FrequentlyAskedQuestions

Q:Ican’thavemyDoorSensorincludedintomyZ‐Wavenetwork,whatamIdoingwrong?
A:1.IsthecontrollerreadytoincludeanydeviceintotheZ‐Wavenetwork?Ifthecontrollerisnotin
Includeorexcludemode,theDoorSensorwillnotbeincludedorexcluded.
2.TheDoorSensorisalreadyincludedinaZ‐Wavenetwork.ExcludetheDoorSensorand
Trytoincludeitagain.

Q:Whydoesn’ttheDoorSensordetectifthedoorisopenorclosed?
A:1.TheDoorSensorisn’tincludedinaZ‐Wavenetwork.Includeitandtryitagain.
2.MakesuretheTamperswitchismountedcorrectly.
3.Themagnetcontactisnotmountedcloseenoughoronthewrongsideofthedevice.

Q:IhaveconfiguredavaluebutwhenIrequestit,itisnotchanged?
A:Itismandatorythatthecorrectsizeisusedwhileconfigureaparameter;gotothedocumentationabout
theconfigurationcommandclasstocheckiftherightsizeisusedduringconfiguration.Ifthewrongsizeisused
theframeisignoredtotally.

Q:IhaveconfiguredanewvalueandwhenIrequestitthecorrectvalueisreturnedbutthebehaviorisstillthe
same?
A:Someconfigurationparametershavelimitsofwhattheycando,gotothedocumentationabout
configurationtocheckifthevalueoftheconfiguredparameterisoutofflimit.

