Wirepath Surveillance WPS-750-BUL-IP User manual

WPS-750-BUL-IP
IP Bullet
Camera
Installation and User’s Manual
Review manual thoroughly before installation.
Retain for future reference.

WPS-750-BUL-IP Installation Manual
1- Safety Instructions
1. Read and follow all instructions and warnings in this manual. Keep for future reference.
2. Install according to manufacturer’s instructions.
3. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
amplifiers) that produce heat.
4. Only use attachments/accessories specified by the manufacturer.
5. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as when the power-supply cord or plug is damaged, does not operate normally, or has been dropped.
6. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of un-insulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.

WPS-750-BUL-IP Installation Manual
Pg. 4
© 2013 Wirepath™ Surveillance
Table of Contents
1-Safety Instructions .......................................................................................................................3
2-Manual Overview ..........................................................................................................................7
3-Required Items for Installation....................................................................................................8
4-Package Contents.........................................................................................................................8
5-Optional Accessories...................................................................................................................8
5.1-Mounts..................................................................................................................................8
5.2-• Power Supplies ..................................................................................................................9
6-Camera Overview..........................................................................................................................10
6.1-Features.............................................................................................................................10
6.2-Camera Connections..........................................................................................................11
6.3-Main Camera Interface.......................................................................................................12
6.3.1-Accessing the Camera........................................................................................................................ 12
6.3.2-Recommendations for Best Performance............................................................................................ 12
6.3.3-Live View Controls.............................................................................................................................. 13
7-System Diagram Considerations.................................................................................................14
7.1-Recommended Equipment.................................................................................................14
7.1.1-Power Supplies................................................................................................................................... 14
7.1.2-Networking Devices............................................................................................................................ 14
7.2-Basic System Diagram.......................................................................................................14
8-Camera Installation.......................................................................................................................15
1-Prepare Camera for Mounting...............................................................................................15
2-Connect The Camera to the System .....................................................................................15
3-Mount the Camera.................................................................................................................16
4-Fine-Tuning Camera Adjustments.........................................................................................16
9-IP Installer Software .....................................................................................................................17
9.1-IP Installer Operation..........................................................................................................17
10-Initial Configuration....................................................................................................................18
1-Assign a Static IP address.....................................................................................................18
2-Enter a Port to uniquely identify and remotely access the Camera. ......................................18
3-Verify Access through the Main Camera Interface ................................................................18
4-Update to the Latest Firmware ..............................................................................................18
5-Configure the Date and Time ................................................................................................18
6-Change the Administrator Password.....................................................................................19
7-Configure User Accounts to Access the Camera ..................................................................19
8-Set the Video Orientation ......................................................................................................19

WPS-750-BUL-IP Installation Manual
Pg. 5
www.snapav.com Support: 866.838.5052
11-Additional Configuration............................................................................................................20
1-Upgrade the Firmware...........................................................................................................20
2-Configure a Privacy Mask......................................................................................................20
3-Configure Motion Detection Areas.........................................................................................21
4-Setup a Schedule..................................................................................................................21
5-Configure Camera for Remote Access..................................................................................22
12-Configuration Menu Operation..................................................................................................23
12.1-System Information...........................................................................................................23
12.1.1-Server Information............................................................................................................................ 23
12.1.2-OSD Setting ..................................................................................................................................... 23
12.1.3-Time Settings.................................................................................................................................... 24
12.1.4-Network LED Light............................................................................................................................ 24
12.2-User Management............................................................................................................24
12.3-System Update.................................................................................................................25
12.4-IP Settings........................................................................................................................26
12.4.1-IP Assignment .................................................................................................................................. 26
12.4.2-Port Assignment ............................................................................................................................... 26
12.4.3-UPnP Settings.................................................................................................................................. 27
12.4.4-RTSP Settings.................................................................................................................................. 27
12.4.5-Multicast Setting ............................................................................................................................... 27
12.4.6-ONVIF.............................................................................................................................................. 27
12.4.7-Bonjour............................................................................................................................................. 27
12.4.8-LLTD (Link Layer Topology Discovery) ............................................................................................. 28
12.5-Advanced IP Settings.......................................................................................................29
12.5.1-HTTPS Settings................................................................................................................................ 29
12.5.2-SNMP Settings................................................................................................................................. 29
12.5.3-Access List....................................................................................................................................... 29
12.5.4-QoS/DSCP....................................................................................................................................... 29
12.6-PPPoE & DDNS Settings .................................................................................................30
12.6.1-PPPoE Settings................................................................................................................................ 30
12.6.2-DDNS Settings ................................................................................................................................. 30
12.7-Server Settings.................................................................................................................31
12.7.1-Mail Settings..................................................................................................................................... 31
12.7.2-FTP Settings..................................................................................................................................... 32
12.7.3-Network Share Settings .................................................................................................................... 32
12.8-Image Settings .................................................................................................................33
12.9-Video Settings ..................................................................................................................35
12.9.1-Streaming 1 & Streaming 2............................................................................................................... 35
12.9.2-Streaming 3...................................................................................................................................... 36
12.9.3-Streaming 4...................................................................................................................................... 36
12.10-Audio Settings ................................................................................................................37
12.11-Event Settings ................................................................................................................38

WPS-750-BUL-IP Installation Manual
Pg. 6
© 2013 Wirepath™ Surveillance
12.11.1-Motion Detection............................................................................................................................. 38
12.11.2-Record File..................................................................................................................................... 38
12.11.3-Record Time Setting....................................................................................................................... 39
12.11.4-Network Disconnected.................................................................................................................... 39
12.11.5-Network IP Check........................................................................................................................... 39
12.12-Schedule ........................................................................................................................39
12.13-I/O Settings.....................................................................................................................40
12.13.1-Input Settings.................................................................................................................................. 40
12.13.2-Output Settings............................................................................................................................... 40
12.14-Log List...........................................................................................................................40
12.15-SD Card..........................................................................................................................41
13-Mobile App Access.....................................................................................................................42
14-Specifications.............................................................................................................................43
15-Dimensions.................................................................................................................................47
16-Warranty......................................................................................................................................48
17-Contacting Technical Support...................................................................................................48
18-Technical Information Glossary................................................................................................49
18.1-Constant vs. Variable Bit Rate..........................................................................................49
18.2-RTSP (Real Time Streaming Protocol).............................................................................49
18.3-ONVIF (Open Network Video Interface)...........................................................................49
18.4-LLTD (Link Layer Topology Discovery) ............................................................................50
18.5-HTTP vs. HTTPS..............................................................................................................50

WPS-750-BUL-IP Installation Manual
Pg. 7
www.snapav.com Support: 866.838.5052
2- Manual Overview
We recommend that this document is read in its entirety before proceeding with system design, installation, or operation of the WPS-
750-BUL-IP camera. When viewing this document electronically, the content identified within references can be quickly located by
clicking on the reference. These references have been formatted as a standard hyperlink so that they can be easily identified with
exception to the TOC which can also be used to link to sections.

WPS-750-BUL-IP Installation Manual
Pg. 8
© 2013 Wirepath™ Surveillance
3- Required Items for Installation
The following items are required during the installation of a Wirepath™ IP Camera. It is recommended that these items are prepared
in advance to ensure that the installation can be performed smoothly.
All Cameras to be installed in the system
Network Connection near the location of the Camera
Administrator rights to the computer that will be used to configure the Camera(s)
oRouter / Switch Details –Contact the network admin to obtain
oAdmin Rights –Required to setup the network and port forwarding for remote access.
oStatic IP to assign to the Camera
oDefault gateway
oSubnet Mask
oDNS Address
Installation Manual for all the Wirepath™ Surveillance IP Cameras being installed
CD-ROM supplied with the Camera
4- Package Contents
(1)
WPS-750-BUL-IP Camera
(1)
WPS-ACC-PWR Power Adapter
(1)
BNC / Power Test Adapter
(1)
Female to Female RJ45 Adapter
(1)
3mm Allen key
(3)
Screws
(3)
Wall Fasteners
(1)
Spare Silica Pack
(1)
Quick Start Guide
(1)
CD-ROM containing documents and setup software
NOTE: A POWER SUPPLY IS NOT INCLUDED WITH THIS CAMERA. The PS-12DC-1A, WPS-PS multiple output power supply or
a Power over Ethernet (PoE) switch is recommended.
5- Optional Accessories
Wirepath™ Surveillance offers a wide range of accessories that provide power to the cameras, allow for various mounting options,
and make connection to the head end quick and easy.
5.1-Mounts
WPS-MNT-FLUSH-BUL
If you're struggling to attach a bullet camera to a J-box, this Flush Mount is the solution. Its versatile hole pattern fits single gang
junction boxes, making it a go-to piece for masonry and commercial applications.

WPS-750-BUL-IP Installation Manual
Pg. 9
www.snapav.com Support: 866.838.5052
5.2-•Power Supplies
Local Power Supplies
PS-12DC-1A
12 Volt 1 Amp Power Supply for Cameras & IR Systems
Remote Power Supplies
Use these remote power supplies to power all the cameras in the system from a remote location.
WPS-PS9-12VDC-10A
9 Output Power Supply - 12V DC, 10A - PTC Fuses
WPS-PS18-12VDC-18A
18 Output Power Supply - 12V DC, 18A - PTC Fuses
Visit www.SnapAV.com for a complete listing of accessories.

WPS-750-BUL-IP Installation Manual
Pg. 10
© 2013 Wirepath™ Surveillance
6- Camera Overview
6.1-Features
2 MegaPixel 16x9 CMOS sensor
This camera sports a 2MP 16x9 CMOS sensor that provides improved picture quality over a typical CCD sensor. Supports full
1080HD up to 1920x1080 at 30FPS.
H.264/ MJPEG/MPEG4 Quadruple Stream Optimization
Supports up to 4 simultaneously streams of compression typically used for the following situations:
oHigh Res stream optimized for NVR Record or Local Network viewing
oLower Res stream optimized for Remote viewing
oLower Res stream optimized for Control Systems (same res as Stream 2)
oLow Res stream for Mobile Viewing
IR up to 65ft
External Zoom and Focus Adjustments
Adjust the camera without the need to remove the lens cap for quick adjustments.
True Day/Night (IR Cut Filter)
For more accurate, vivid color reproduction during daytime use, an IR Cut filter is automatically moved over the lens to block
unwanted IR. At night, the filter is removed to deliver maximum visibility and clear IR illumination.
Advanced Image Processing
Advanced DSP (Digital Signal Processor) to improve image quality including:
oSense Up: Automatically slows the shutter speed to improve image quality in low light.
oD-WDR (Digital Wide Dynamic Range): Provides clearer images and even lighting in applications that are simultaneously
bright and dark. This is particularly useful in areas with windows and lots of natural light.
oDigital Noise Reduction (DNR): Intelligently scans the image and reduces noise in low-lux conditions for a cleaner, crisper
image.
Privacy Mask
Block out sensitive or privileged areas by placing rectangular blocks or "masks" over up to three installer-defined areas.
Power Over Ethernet (PoE IEEE 802.3af)
Camera can be powered by PoE using the same Cat5e/Cat6 cable that connects to the network. No need to pull a 2nd power
cable to the location. Compatible with all PoE network switches that support PoE IEEE 802.3af and PoE power injectors.
Edge Storage
The camera supports microSD cards (up to 32GB, card NOT included). Images, short recordings and logs can be stored on a
microSD installed into the camera. This is useful as a backup if the network connection to the NVR is lost.
Alarm input and outputs
1 In / 1 Out, transistor contact closures
Test Port for Quick Setup during Install
oAnalog Video Out
oLocal Power for Camera
IP-66 Weatherproof Rating
With an IP-66 rating, this camera is protected from dust and water making it at home in indoor and outdoor installations.
ONVIF

WPS-750-BUL-IP Installation Manual
Pg. 11
www.snapav.com Support: 866.838.5052
6.2-Camera Connections
2345
1
1. Ethernet Connection (RJ45)
Connect to network switch for communication to and from the camera. Pin out follow EIA standard 568-B
2. 12V DC Power In (Barrel Connector)
Connect to a 12V DC 1A power supply. The camera is not supplied with a power supply, see section 5.2-Power Supplies
for details on the power supply options available from Wirepath™.
Note: No power supply is needed if PoE is being used to power the camera via the Ethernet connection.
3. Audio In (1/8” - 3.5mm Mono)
Connect to a powered microphone such as the WPS-ACC-MIC to allow for listening to audio at the cameras location.
Note: A 3.5mm 1/8” Mono male to male adapter is required (not included)
4. Audio Out(1/8” -3.5mm Mono)
Connect to an amplifier and speakers to allow for communication between the viewer and the cameras location.
5. Contact & Relay (Spring Loaded Terminal)
Connect to devices with contact closure activation to trigger recording from the camera, or activate devices such as sirens
at the cameras location.

WPS-750-BUL-IP Installation Manual
Pg. 12
© 2013 Wirepath™ Surveillance
6.3-Main Camera Interface
Note: The camera requires configuration before accessing for the first time. See sections 9-IP Installer Software and 10-
Initial Configuration before opening the browser.
6.3.1- Accessing the Camera
Note: IE 8.0 or higher is required to access the camera; other browsers are not supported at this time.
A. Open the web browser, and enter the IP Address that was assigned to the camera. The address should include the port
number assigned to the camera. Note that access varies between local network and remote access through a DDNS.
Local Network Example:
http://192.168.1.56:8056
Remote Access (DDNS) Example:
http://JonesIPCamera.Wirepathdns.com:8056
B. A window will open asking for a username and password.
Default Username and Password:
Username:
admin
Password:
admin
Recommendation: After initial setup of the Cameras, we recommend that the password be changed to avoid
unwanted access.
C. Install the ActiveX control if prompted to do so.
D. After installing the ActiveX the camera should be visible in the web browser, if the camera does not appear, verify the IP
address by using the IP Installer.
6.3.2- Recommendations for Best Performance
As the number of open browser windows or tabs increases, the risk of slowed response time to the cameras increases. We
recommend that open browser windows or tabs be limited to no more than 4 to avoid interruption in communications or reduced
response time with the cameras.
Due to the limited upload speeds set by ISP (Internet Service Provider) we recommend that Streaming 2 is selected when viewing the
cameras remotely (outside the local network) as the lower resolution provides better frame rates allowing for a smoother video
stream.

WPS-750-BUL-IP Installation Manual
Pg. 13
www.snapav.com Support: 866.838.5052
6.3.3- Live View Controls
6.3.3.1- Top of Screen
1 2 3 4 5 6 7
1. Video
Expands the camera’s image to full screen. Press ESC or double click on full screen image to return to Live View screen.
2. Digital Zoom
A. Select the checkbox to enable Digital Zoom.
B. Move the slider to the desired zoom level.
C. Click and hold on the green box in the preview window to select a desired location to view.
D. Click on the X in the upper right hand corner to close the Digital Zoom window.
Note: The Live View video will remain at this zoom level and area selection only for the current viewing session. When
the user leaves Live View for any reason, zoom level will be reset to 100%.
3. Audio Out
Mutes or Un-Mutes Audio to a speaker connected to the Camera, if installed.
4. Audio In
Mutes or Un-Mutes Audio from the microphone connected to the Camera, if installed.
5. Record
Records the current live stream to an .AVI video file in the selected location on the PC or network. A dialog window opens
prompting for the storage location. Press Record again to stop the recording.
Note: The quality of this recording will vary based on the bandwidth of the connection to the camera and the processing
power of the local computer.
6. Photo
Takes a JPEG snapshot of the current image that can be saved to the PC.
7. Config
Opens the Camera’s configuration menu.
6.3.3.2- Bottom of Screen
1 2 3
1. Live View Window Size
Adjusts the size of Live View within the browser window.
2. Video Streaming
Allows for selection of one of two video streams from the camera. Typically Streaming 1 is configured for a high resolution
stream for viewing over a higher bandwidth connection, and Streaming 2 is a lower resolution for viewing over low
bandwidth connections.
3. Relay Output
Opens and closes the Relay contact connection.

WPS-750-BUL-IP Installation Manual
Pg. 14
© 2013 Wirepath™ Surveillance
7- System Diagram Considerations
7.1-Recommended Equipment
7.1.1- Power Supplies
Wirepath™ Surveillance IP Cameras can be power using PoE (Power over Ethernet) which supplies power via the Cat5e/Cat6
Ethernet connection. We recommend this method be used as it limits the amount of wiring required thus drastically reducing
installation time. When this method is used a router/switch that is equipped with PoE capabilities or a PoE injector must be used.
Recommendation: We recommend using PoE enabled switches to eliminate the need for separate power supplies reducing the
amount of wiring and decreasing installation time.
7.1.2- Networking Devices
Streaming content from IP Cameras requires bandwidth greater than most devices. We recommended the use of 1Gbps routers and
switches in order to maintain a high quality streaming image. Additionally, to reduce traffic on the overall network, we recommend
that all IP Surveillance devices be connected to a dedicated 1Gbps switch or dedicated VLAN.
7.2-Basic System Diagram
WPS-750-BUL-IP
1Gbps Network
Switch
1Gbps Router
Internet
1 2 3 4 5 6 7 8 N C NO
COM
RS-485 ALARMIN
HDMIOUTPUT
HDMI
VGA
RELAY
ETHERNETGNDGND VGAOUTPUT
12VDC6A
INPUT
Wirepath NVR

WPS-750-BUL-IP Installation Manual
Pg. 15
www.snapav.com Support: 866.838.5052
8- Camera Installation
1- Prepare Camera for Mounting
Prior to mounting to the Camera, we recommend that the position and angles be preset in order to reduce configuration time.
These settings can be fine-tuned once the Camera is mounted.
A. Adjust Camera Rotation
B. Adjust Swivel of Camera
C. Adjust Camera Angle
A
B
C
2- Connect The Camera to the System
Recommended Cabling
Ethernet
Cat5e/Cat6
DC Power
16/2 (if using a remote power source other than a PoE switch)
Audio In/Out
16/2
POE Consumption
PoE IEEE 802.3af
3.84W(IR Off) / 7.56W(IR On)
A. Connect the Ethernet connection to a Cat5e/Cat6 cable using the provided RJ45 female/female adapter. The opposite
end of the Cat5e/Cat6 will be connected to the network switch.
B. Connect the DC Power In to a 12V DC 1A power supply using the included WPS-ACC-PWR DC power adapter. If using
PoE to power the Camera, this step can be omitted.
Tip: The power supply can be located at the head end of system using a WPS-PS multiple output power supply and
prewiring a power wire.
C. Connect the Audio Out of a WPS-ACC-MIC to the Audio In jack of the Camera using an RCA Male to 3.5mm mono male
adapter. If no microphone will be used, this step can be omitted.
Note: The WPS-ACC-MIC requires power, if PoE is being used, a power supply for the microphone will need to be
installed.
D. Connect the Audio Out (Green) on the Camera pigtail to a 3.5mm mono male plug. This will be connected using 16/2 to
an amplifier for playback of the microphone. If no audio output is being used, this step can be omitted.
E. Connect an Alarm output or input to the connecting block. If no alarm functions are being used, this step can be
omitted.

WPS-750-BUL-IP Installation Manual
Pg. 16
© 2013 Wirepath™ Surveillance
DI +5V DC 50mA max
N.O. –Trigger on contact closure
N.C. –Trigger on contact open
GND Ground
DO Open: +5V DC 50mA max
Closed: 0V DC
DI
GND
DO
3- Mount the Camera
Tip: Before mounting the Camera, write down the Cameras Mac Address, Model Number, and location. These will
come in handy during setup or if troubleshooting is required.
A. Mounting directly to a wall or eve:
B. Use the Camera base as a template to mark the screw locations.
C. Predrill holes in the marked locations.
D. Connect the wires from the wall to the Cameras Pigtail and insert them into wall.
E. Position the Camera base over the marked holes from step 3-A.
F. Secure the Camera with the provided screws
G. Mounting to a Single gang Junction Box
We recommend the use of the WPS-MNT-FLUSH-BUL Flush Mount plate when mounting to a single gang junction box.
This plate is available in gray and white to match the color of the Camera being used. Follow the instructions in the
WPS-MNT-FLUSH-BUL manual for using this mounting method and then proceed to step 4.
4- Fine-Tuning Camera Adjustments
The Camera is equipped with a BNC Test Port that allows for local Analog Video output and power to the Camera for
adjusting positioning, zoom, and focus.
The camera is supplied with a BNC Test Adapter that allows for viewing the output of the camera on a monitor or the WPS-
CCTV-TESTER (not included). Use this connection to adjust the camera directly from the installed location.
A. Remove the plate located at the rear of the Cameras just before the Cameras base to access the BNC Test Adapter
connection.
B. Connect the BNC Test Adapter to the Cameras.
C. Connect the BNC on the adapter to a monitor or
WPS-CCTV-TESTER video in.
D. Connect a Power Supply to the Power connection
on the BNC Test Adapter if no other power
connection is active.
E. Adjust the Cameras Rotation, Swivel, and Angle
as defined in step 1 and secure the set screws
using the supplied 3mm Allen key.
F. Adjust the Cameras Zoom (closest to the lens)
using the supplied 3mm Allen key.
G. Adjust the Cameras Focus (furthest from the lens)
using the supplied 3mm Allen key.
H. Once the Zoom and Focus are adjusted,
disconnect the BNC Test Adapter and replace the
plate removed in step 4-A.
Adjust Zoom
Adjust Focus
BNC Test Adapter
Connection

WPS-750-BUL-IP Installation Manual
Pg. 17
www.snapav.com Support: 866.838.5052
9- IP Installer Software
The IP Installer software provides a quick view of Wirepath™ IP Surveillance devices connected to local network. This software is
required for initial setup of any Wirepath™ IP Surveillance device.
Recommendation: Before starting any configuration or service of Wirepath™ IP devices, we recommend that the latest version of
the IP Installer is downloaded from www.SnapAV.com to ensure that all functionality is available.
VPN Important Note: The IP Installer is not able to locate IP Devices if VPN connections are active. Close all VPN
connections before running the IP Installer.
1. Install the IP Installer
A. Copy the WPS IP Installer from the CD-ROM or download it from www.SnapAV.com to a PC.
Note: The WPS IP Installer is a native executable application and does not require installation on the PC. We
recommend that it be manually copied to a known location on your work/install computer/laptop for easy
access.
2. Open the WPS IP Installer.
Once open, the installer will scan the network for Wirepath™ IP Cameras, NVRs, and Cameras that are connected to the
network. If no devices appear, select Search Devices button to initiate a scan of the network.
9.1-IP Installer Operation
1 2
3 4
1. Connected Device List
Displays a list of all connected Wirepath™ IP surveillance device
names, and IP address.
2. Device Name and Network Settings
Used to configure the devices network settings. MAC address cannot
be changed.
See section 10-Initial Configuration
3. Search Devices
When selected, the IP Installer will scan the network for connected
devices that are powered on.
4. Submit
Select to submit changes made to the network and name settings for
the selected device.

WPS-750-BUL-IP Installation Manual
Pg. 18
© 2013 Wirepath™ Surveillance
10- Initial Configuration
1- Assign a Static IP address
By default the Camera will receive an IP address via DHCP; however, it is recommended that the Camera is assigned a
static IP address, and given a 4 digit port. Using a static IP address ensures that the address will not change due to
changes to the router.
Note: The static IP used should be outside the DHCP range of the router to avoid conflicts with other devices on
the network.
A. Open the IP Installer, and select the Camera from the list of devices. The Camera name will highlight Blue in the list.
B. Select Static at the top of the right side column. This will allow for manual entry of the network configuration settings.
C. Enter the IP address issued by the network admin.
D. Enter the Net Mask assigned by the network admin.
E. Enter the default Gateway assigned by the network admin.
F. Enter the DNS 1 address assigned by the network admin.
G. Enter the DNS 2 address assigned by the network admin. If only 1 DNS address is used, this must be “0.0.0.0”.
Note: Any data displayed in these fields should be replaced with information obtained from the network admin to
ensure they are set properly.
H. Assign a name to the Camera that will identify it easily when using the IP Installer or configuring a Wirepath™ NVR, and
for recordings, or captured images.
Example: FrontDoor1
2- Enter a Port to uniquely identify and remotely access the Camera.
Recommended Port Numbering
Each Camera must have a unique port number for Remote Access from outside the local network. To make port
numbering consistent, and easy to remember we recommend that the ports be 4 digits, and contain the IP address of
the Camera starting with 8.
Example:
IP Address
Port
192.168.1.050
8050
192.168.1.100
8100
3- Verify Access through the Main Camera Interface
Once the IP Address has been set, the camera can be accessed through the web browser. Note that on initial access to
each camera, ActiveX controls will need to be installed on each PC that is used to access the camera.
See section 6.3.1-Accessing the Camera for details on how to access the camera via a web browser.
4- Update to the Latest Firmware
While the camera is shipped with the latest firmware available at the time, newer firmware may be available with
improvements.
Recommendation: We recommend that you check for the latest firmware version on www.SnapAV.com and update if
needed before proceeding. See step 1-Upgrade the Firmware in section 11-Additional Configuration for details.
5- Configure the Date and Time
To ensure that recordings and photos are accurately time stamped, the Date and Time of the camera need to be set to the
correct time for the location of the camera.
See section 12.1.3-Time Settings for details on the features used in this step.
A. Select Config Button in the upper right hand corner of the Main Camera Interface.
B. Select System Information in the left side menu.
Tip: Using an NTP server, and setting the time zone, and enabling DST is the best method for maintaining accurate
time. We recommend that pool.ntp.org is used as it pulls time from a range of time servers that provide backup to
each other in the event of server outage.

WPS-750-BUL-IP Installation Manual
Pg. 19
www.snapav.com Support: 866.838.5052
6- Change the Administrator Password
Now that the camera is visible on the network, we recommend that the administrator password is changed from the default to
prevent unwanted access.
See section 12.2-User Management for details on the features used in this step.
A. Select Config Button in the upper right hand corner of the Main Camera Interface.
B. Select User Management in the left side menu.
C. Select Edit next to the admin username in the user list at the bottom of the screen to open the User Setup window.
D. Edit the Username (if desired) and New Password, and Confirm the new password.
E. After selecting OK, the user login window will open. Enter the new password to continue.
7- Configure User Accounts to Access the Camera
There are 2 levels of users, Administrator which is the default admin account, and Guest accounts. The admin account is
the only account that can be set as an administrator. An unlimited number of Guest accounts can be added that can view
and control the function of the camera, but will not be able to access or modify any of the cameras settings.
Access to the Camera varies based on the level:
Administrator
Has access to all functions of the Camera including configuration.
Guest
Has access to view the Camera, and has limited control for saving recordings, and photos. No configuration
is allowed for the guest level. Guests attempting to access to the camera configuration will be prompted for
the Admin username and password.
Note: Once a username is created it cannot be edited, only the password can be changed. If a username needs
to change, it will need to be removed, and a new name created.
See section 12.2-User Management for details on the features used in this step.
A. Select Config Button in the upper right hand corner of the Main Camera Interface.
B. Select User Management in the left side menu.
C. Enter a Username and Password for a new user.
D. Re-Enter the password in the Confirm field, and select Add to confirm the addition.
8- Set the Video Orientation
By default, the camera is configured for mounting on the ceiling, or under and eave (bullet facing down). This allows for the
image to be right side up when viewing. Installations where the camera is mounted on a shelf or other flat surface (bullet
facing up), the video image must be flipped.
See section 12.8-Image Settings for details on the features used in this step.
A. Select Config Button in the upper right hand corner of the Main Camera Interface.
B. Select Image Setting under A/V Setting on the left side Menu.
C. Select Flip and/or Mirror checkbox next to Video Orientation as required, and then select save.

WPS-750-BUL-IP Installation Manual
Pg. 20
© 2013 Wirepath™ Surveillance
11- Additional Configuration
Recommendation: While the camera can be configured remotely from outside the local network, operation can be slow. We strongly
recommend that the bulk of configuration be performed via the local network to avoid slow response times.
1- Upgrade the Firmware
See section 12.3-System Update for details on the features used in this step.
A. Download the latest firmware from www.SnapAV.com.
Note: If no firmware appears on the products support tab, there have been no updates to the firmware since
the initial release.
B. Select Config Button in the upper right hand corner of the Main Camera Interface.
C. Select System Update in the left side menu.
D. If the firmware version listed is below the version on the site, then firmware should be updated.
E. Select Browse, navigate to the folder containing the firmware, select the latest firmware file, and select Open.
F. Select Upgrade to start the update process.
WARNING: Firmware upgrade must be performed from a wired connection on the local network. While it is
possible to recover from an update that fails due to a lost connection, the camera will be inoperable until a
successful upgrade is performed from a reliable connection.
2- Configure a Privacy Mask
Privacy mask allows for areas of an image to be blocked out to avoid unwanted capturing of sensitive areas. For Example: A
camera used to monitor the front lawn of a house would have the windows on the neighboring homes masked to avoid
peeping on the neighbors.
See section 12.8-Image Settings for details on the features used in this step.
A. Assigning a Privacy Mask
A.1-Select Image Setting under A/V Setting on the left side Menu.
A.2-Select Area 1 next to the blue box.
A.3-Place the mouse at the upper left hand corner of the area to mask, hold down the left mouse button and drag the
box over the area to mask and release the mouse button. The area to be masked will be indicated by a colored
grid.
Draw Mask Area
A.4-Select Save to save the setting. The selected area will now display a black privacy mask under the colored grid,
and this area will be blacked out in all viewed and recorded video.
A.5-Repeat Steps B-D for Area 2 & 3 if more areas are needed.
B. Removing a Masked Area
B.1-Select the button for the area to remove. The colored grid for the selected area will be removed.
B.2- Select Save to save the change. The black privacy mask will be removed.