Wisdom IA-8DSP User manual

Owner’s Manual
IA-8DSP
8-Channel Amplifier with DSP

IA-8DSPDSP
2
WISDOMAUDIO.COM

IA-8DSPDSP
3
WISDOMAUDIO.COM
Table of Contents
Important Safety Instructions | 5
Unpacking the IA-8DSP | 6
Included Accessories | 6
Placement Considerations | 6
Ventilation | 7
Operating Voltage | 7
Rackmount Installation | 7
Front Panel | 8
Rear Panel IA-8DSPDSP | 11
Care & Maintenance | 17
North American Warranty | 18
Obtaining Service | 19
Specifications | 20
Dimensions | 21
Document Conventions
This document contains general safety, installation and operation instructions for the Wisdom Audio IA-
8DSP Amplifier. It is important to read this document before attempting to use this product. Pay
particular attention to:
WARNING: Calls attention to a procedure, practice, condition or the like that, if not correctly performed
or adhered to, could result in injury or death.
CAUTION: Calls attention to a procedure, practice, condition or the like that, if not correctly performed
or adhered to, could result in damage to or destruction of part of or the entire product.
Note: Calls attention to information that aids in the installation or operation of the product.

IA-8DSPDSP
4
WISDOMAUDIO.COM
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE
COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED PERSONNEL.
1. The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
2. Warning:The apparatus with CLASS I construction shall be connected to a MAINS socket
outlet with a protective earthing connection.
3. Warning: The mains plug or appliance coupler is used as disconnect device, the disconnect
device shall remain readily operable
DANGER:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying this equipment.
Marking by the “CE” symbol (shown left) indicates compliance of this device with the EMC
(Electromagnetic Compatibility) and LVD (Low Voltage Directive) standards of the European
Community.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and the receiver
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
•Consult the dealer or an experienced radio/TV technician for help

IA-8DSPDSP
5
WISDOMAUDIO.COM
Important Safety Instructions
Please read all instructions and precautions carefully and completely before operating
your Wisdom Audio equipment.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade of the third
prong are provided for your safety. If the provided plug does not fit into your
socket, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Unplug this apparatus during lightning storms or when unused for long periods
of time.
13.Refer all servicing to qualified personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
14.ALWAYS disconnect your entire system from the AC mains before connecting
or disconnecting any cables, or when cleaning any component.
15.NEVER operate this product with any covers removed.
16.NEVER wet the inside of this product with any liquid.
17.NEVER pour or spill liquids directly on to this unit.
18.NEVER bypass any fuse.
19.NEVER replace any fuse with a value or type other than those specified.
20.NEVER operate this product in an explosive atmosphere.
21.ALWAYS keep electrical equipment out of the reach of children.

IA-8DSPDSP
6
WISDOMAUDIO.COM
Unpacking the IA-8DSP
CAUTION:
Do not attempt to lift your IA-8DSP while bending or twisting from the waist. Use your legs for lifting,
not your back. Always stand as straight as possible and keep the IA-8DSP close to your body to
reduce strain on your back.
After unpacking your IA-8DSP, keep all packing materials for future transport. In the
event that you need to ship your IA-8DSP, only the original, purpose-designed
shipping carton is acceptable. Any other method of shipping this product runs a
significant risk of damage to the IA-8DSP; damage that would not be covered by the
warranty.
Carefully inspect your IA-8DSP for possible damage due to shipping. If you discover
any, contact your Wisdom Audio dealer immediately.
Included Accessories
•Power Cord (North America) –IEC 320-C19/Nema 5-15P
•Power Cord (EU) –IEC 320-C19/CEE 7/7
•Rackount Ears Left/Right
•Screws (6) Torx T10, Black
•Torx Wrench –T10
Placement Considerations
PRECAUTION
For your protection, review “Important Safety Instructions” before you install your IA-8DSP.
Note that adequate clearance for the AC cord and connecting signal cables must be
left behind your IA-8DSP. We suggest leaving at least six inches (15 cm) of free space
behind your IA-8DSP so all cables have sufficient room to bend without crimping or
strain.
If possible, the IA-8DSP should also be placed in such a way that the power switch on
the rear panel is easily accessible. This switch disconnects power from the unit
completely, resulting in effective disconnection of the IA-8DSP from the AC mains.
You might think of this as a “vacation switch”, should you wish to turn off your system
completely when you will be away from home for a prolonged period of time. Just
remember to turn it back on again when you return.

IA-8DSPDSP
7
WISDOMAUDIO.COM
Ventilation
Your Wisdom Audio IA-8DSP has relatively modest ventilation requirements, thanks to
its remarkably efficient design. Typically, it becomes only modestly warm during
normal operation. Still, please be certain to keep the vents on the sides of the
amplifier clear of any obstruction. (The rack mount attachments have corresponding
vents.)
Mechanical drawings are included in this manual to facilitate special installations where
necessary (see “Dimensions” at the end of this manual).
Operating Voltage
For compatibility with existing household outlets, a standard three prong, 20-ampere
plug is provided on the removable, IEC-standard AC mains cable.
The Wisdom Audio IA-8DSP has a universal 100V-240V, 50hz-60hz AC mains
operation. Outside the United States, and depending on local electrical codes and
regulations, the AC mains cord may need to be replaced with one that conforms to
local plug/outlet standards.
NOTE: The AC receptacle employs a 20-amp IEC 320-C19 standard socket (not a 15-amp IEC socket).
Rackmount Installation
Rack mount ears are included with the IA-8DSP and IA-8DSPDSP. These allow the
amplifier to be mounted in a standard 19” wide rack mount. Each amplifier requires
2RU of height.
1. Remove the three (3) T10 screws on the side of the unit closest to the front
faceplate using the included T10 Torx screwdriver.
2. Place the rack ears over the side panel and align with the screw holes.
3. Attach the rack ears with the black Torx screws included with the Rack Ears.

IA-8DSPDSP
8
WISDOMAUDIO.COM
Front Panel
1. Power Indicator: The international symbol for power is inscribed in this location to
designate its purpose. When power is first switched on, the IA-8DSP will turn on
automatically. The only way to place the unit is Standby is with the DC Trigger
(above). An AC mains switch is located adjacent to the power cord on the rear
panel of the SW-1DSP. This switch may be used to disconnect the unit from the AC
mains without having to unplug the SW-1DSP from the wall outlet.
If you plan to be away for an extended period or have any other reason to turn the
SW-1DSP completely off, you may either unplug the SW-1DSP or you may use the
AC mains switch. There are three normal states for the lit indicators
•Lit amber LED on left side indicates the unit is receiving power and is in standby
•Lit blue channel status indicators indicate the unit is receiving power and is on
•If both the amber and blue LEDs are off, no power is being supplied
2. Channel Status Indicators: These eight LEDs provide visual confirmation of the
operational status of the eight channels in your IA-8DSP.
The IA-8DSP has built in monitoring for each amplifier channel for temperature and
clipping, as well as a system power supply temperature and mains AC line voltage.
This ensures the amplifier will operate safely. The front panel LED indicators will
display the status of the unit.

IA-8DSPDSP
9
WISDOMAUDIO.COM
•All Blue LED On = Normal Operation
•Individual Channel Blue LED OFF = Clipping Error. The LED will be OFF to
indicate the channel is disabled. The IA-8DSP will disable a single channel if that
channel has clipping at either the input into the amplifier module or the output
of the amplifier module, and then will enable the channel after waiting 15
seconds. If Clipping is still occurring the channel will disable again and retry. If
this continues to happen, remove the input and/or output for the indicated
channel and check for shorts or excessive input signal level.
•Blue LED Blinking 2x Per second = Overtemperature Error. A single channel has
been disabled due to Overtemperature. The IA-8DSP will disable the channel
and wait until the channel temperature returns to normal and then automatically
restart normal operation. This is monitored individually for each channel.
•ALL Blue LED Long Blink Together (Mostly On) = Power Supply Over-
temperature. The LED will be mostly ON with a short off blink to indicate a
power supply error. If the power supply has a fault such as Over-temperature or
Over-Current the system will MUTE all channels and wait for the error to clear
before restarting normal operation. In this case the unit may be being
overdriven across all channels for too long.
•Amplifier Turns Off Automatically = If there is a critical fault in the amplifier
power supply such as a blown fuse or internal error, the unit will turn off and not
allow the unit to power on. This will also happen if the incoming mains voltage
is too high or too low, such as a brown out or power failure condition.
•All Blue LED Short Blink (Mostly Off) = Amplifier (all channels) are disabled. This
can indicate an internal problem with the high output amplifier or an internal
communication error. Power cycle the amplifier to check for normal operation.
If this error continues the amplifier needs to be checked by a qualified service
technician. Do not open the cover without training and safety equipment.

IA-8DSPDSP
10
WISDOMAUDIO.COM
Troubleshooting:
•If one or more indicators are blinking or will not turn on, and will not turn back
on automatically, turn off the amplifier and completely disconnect the speaker
wires for the offending channel. Turn the amplifier back on and check the status
indicator. If it is still blinking, there is likely an internal problem within the IA-
8DSP. Please contact your local Wisdom Audio dealer or Wisdom Audio’s
Technical Service department for assistance
•If removing the speaker wires from the offending channel appears to solve the
problem; check the DC resistance across the speaker leads you disconnected.
It should read several ohms (the exact number varies a bit by model). If the DC
resistance is under 1Ω, carefully check all the connections to make sure no
speaker wires are touching each other or shorted out as a result of their
insulation having been damaged. If yours is a custom installation with wires that
are run in the walls, you should probably call your Wisdom Audio dealer for
assistance trouble-shooting the installation.

IA-8DSPDSP
11
WISDOMAUDIO.COM
Rear Panel IA-8DSPDSP
1. Balanced Audio Inputs
2. Speaker Output Terminals
3. DC Trigger In and Out
4. AC Mains Input (IEC 320-C19) and Switch
5. Ethernet / USB system setup and diagnostics
6. DANTE Audio over IP (Optional –Dealer Installed)
7. Network Reset
CAUTION! Turn off the IA-8DSP before attempting to make or change any connections.

IA-8DSPDSP
12
WISDOMAUDIO.COM
1. Balanced Audio Inputs
These balanced audio inputs accept output signals from a preamp or
surround processor via a high quality XLR connector.
The pin assignments of this XLR-type female input connector are:
Pin 1: Chassis ground
Pin 2: Signal + (non-inverting)
Pin 3: Signal –(inverting)
Connector ground lug: chassis ground
These pin assignments are consistent with the standards adopted by the Audio
Engineering Society. Connect the appropriate outputs of your preamp to these
inputs, using our WWK-BB8 / CUSTOM-WWK-BB8 balanced audio interconnect kits. If
using off the shelf interconnects or making your own cables, only use shielded 3
conductor audio cable.
2. Speaker Output Terminals
The Wisdom Audio SA-series amplifiers are equipped with high-current binding posts
for output termination to the loudspeaker system. To take full advantage of the
amplifier’s sonic quality, we recommend using high- quality speaker cable; please see
your Wisdom Audio dealer.
CAUTION!
NEVER connect a power amplifier’s output terminals to any device other than a loudspeaker.
NEVER short-circuit the amplifier’s output terminals.
NEVER connect the output terminals of one amplifier to the output terminals of another amplifier.
Connect the + (positive) output post of the amplifier to the + (positive) input terminal
of the appropriate loudspeaker. Connect a –(negative or black) output post of the
amplifier to the –(negative or black) input terminal of the appropriate loudspeaker.
Take care to maintain this proper polarity throughout the system.

IA-8DSPDSP
13
WISDOMAUDIO.COM
3. DC Trigger In and Out
These 12v trigger jacks provide compatibility with a wide range of
products to facilitate remote turn-on and turn-off in systems.
These 1/8” (3.5 mm) “mini-jacks” allow other components to bring the IA-8DSP in and
out of standby. Two such mini-jacks are provided to allow “daisy-chaining” of this
turn-on signal with other components, including additional amplifiers.
The remote trigger input will be operated by any positive-polarity DC signal between
4–20 volts (only a few milliamps are required), with tip polarity as shown below
The DC Trigger Input has priority over the front panel switch. Therefore, if a trigger
voltage is present at this input connector, the unit will be forced on and the front
panel switch will be ignored. When the voltage transitions from high to low (off), the
unit will go into standby.
When there is no voltage present at the trigger input (either because the controlling
device is not sending, or because the plug is removed), the front panel switch will
operate the IA-8DSP, as you would expect.
The 12v Trigger Output jack is driven to a “high” state of 12 volts a few seconds after
the IA-8DSP is turned on and can source as much as 100 mA of current at 12 volts.
This signal may be used in turn to control other components, such as additional
Wisdom Audio SA-series amplifiers. Each Wisdom Audio component has a short delay
built into its DC trigger system to facilitate a staggered turn-on sequence.
Your Wisdom Audio dealer can help you take advantage of these design features to
maximize your system’s convenience and versatility.
4. AC Mains Input & Switch
An IEC 320-C19 removable power cord is used with the IA-8DSP. A high quality AC
mains cord is included with the product, although the use of the standardized IEC
receptacle means that you may easily substitute another high quality AC mains cord if
you wish
Note: due to the high current nature of the IA-8DSP, it uses a 20-ampere IEC
receptacle, rather than the more common 15-ampere version, and it will not accept a
15-ampere cord. If you decide to use an after-market power cord, it must employ the
compatible 20- ampere IEC 320-C19 connector.
Input Signal: 4-20 volts @ less than 10 mA
Output Signal: 12 volts @ 100mA

IA-8DSPDSP
14
WISDOMAUDIO.COM
WARNING! Your new Wisdom Audio IA-8DSP has been safety-tested and is designed for operation
with a three-conductor power cord. Do not defeat the earth ground of the AC power cord.
An AC mains switch is located above the power cord on the rear panel of the IA-8DSP.
This switch may be used to disconnect the unit from the AC mains without having to
unplug the IA-8DSP from the wall outlet.
If you plan to be away for an extended period or have any other reason to turn the IA-
8DSP completely off, you may either unplug the IA-8DSP or you may use the AC mains
switch.
DANGER! Potentially dangerous voltages and current capabilities exist within your IA-8DSP. Do not
attempt to open any portion of the IA-8DSP’s cabinet. There are no user-serviceable parts inside your
IA-8DSP. All service of this product must be referred to a qualified Wisdom Audio dealer or
distributor.
5. Ethernet and USB
The Ethernet connection allows for simple monitoring of the IA-8DSP. At this time
there are no user accessible setting and no connection to the network is required for
operation.
For the IA-8DSPDSP, connection to a local network will allow for setup of the internal
DSP using the built in web-server user interface. This should only be conducted by an
Authorized Wisdom Audio installer. The ethernet interface does not need to be
connected after setup is complete and can be disconnected if desired.
The USB connection is included for Factory Use only. If directed by Wisdom Audio this
port may be used for diagnostic or firmware updates but is not needed in normal use.
Connecting the IA-8DSP on a Local Area Network with DHCP Server
This is the most common connection method and will be used by most standard home
networks. There are several connection options below.
For multiple amplifiers on a single network, we recommend connecting one at a time,
and renaming them with a unique name or Static IP Address.
Connect the IA-8DSP unit to the Local Area Network (LAN) by plugging an Ethernet
cable into the Ethernet port on the rear of the unit and to an open port on the
network router or switch. This is NOT the DANTE port. Turn on the unit and take it out
of standby.

IA-8DSPDSP
15
WISDOMAUDIO.COM
The IA-8DSP should always be discoverable via its mDNS name. You may need to
install an mDNS application such as Bounjour Print Services for Windows from Apple.
To access the IA-8DSP, open a web browser (Wisdom Audio recommends Firefox) and
search for the following address:
http://IA-8.local
If the IA-8DSP cannot be located using mDNS, it can be accessed via IP address. First
locate the IP address of the IA-8DSP by performing an IP scan of the network using a
scanner such as the Advanced IP Scanner.
Identify by Name or MAC Address 8C:1F:64:D5:6x:xx
Once the IP address has been discovered, use it to access the Speaker Wizard by
entering the IP address as shown in the example below:
Example: 192.168.1.35
Direct Connection without a Network and/or without a DHCP Server
If the above methods do not work, you can connect directly without a router or switch.
The IA-8DSP will have a default IP Address of 169.254.0.8 if no DHCP router is found.
This can happen if you are using a switch only, or have connected directly from your
computer to the IA-8DSP. Note that you can only connect one (1) SA-x at a time with
this method.
Connect the SA-x unit to the Ethernet port of your computer by plugging an Ethernet
cable from the computer directly to the SA-x without a router or switch. Turn on the
unit and take it out of standby.
Open your web browser and enter the IP Address of 169.254.0.8

IA-8DSPDSP
16
WISDOMAUDIO.COM
6. DANTE (Dealer Installed Option)
RJ45 connection for DANTE and AES67 audio. Proper connection should only be done
by trained installers. DANTE training can be obtained by contacting
www.audinate.com. Training is free and available online. Do not connect the home
network to this connection unless directed by Wisdom Audio, or by an Audinate
trained or DANTE certified installer.
Gigabit switches are recommended, and 100Mbps switches may be used in limited
scenarios.
•For low channel count (<32) applications, a 100Mbps switch may be used as
long as it supports proper QoS, and QoS is active. The use of 100Mbps
switches without QoS is not recommended or supported.
•For higher channel counts, Gigabit switches are essential. QoS is recommended
for Gigabit switches on networks that share data with services other than Dante.
Dante makes use of standard Voice over IP (VoIP) Quality of Service (QoS) switch
features, to prioritize clock sync and audio traffic over other network traffic. Any
switches with the following features should be appropriate for use with Dante:
•Gigabit ports for inter-switch connections
•Quality of Service (QoS) with 4 queues
•Diffserv (DSCP) QoS, with strict priority
•A managed switch is also recommended, to provide detailed information about
the operation of each network link: port speed, error counters, bandwidth used,
etc.
•The ability to deactivate Energy Efficient Ethernet (EEE). Unmanaged switches
that feature EEE should not be used with Dante.
7. Network Reset Switch (For Qualified Installers Only)
•“Network Reset” - Press and hold reset button for 5 seconds with unit
ALREADY POWERED ON will do the following:
oReset IP to DHCP
oReset Host Name to “IA-8”
oReset DHCP servers
oDoes not clear any USER memory settings.

IA-8DSPDSP
17
WISDOMAUDIO.COM
Care & Maintenance
To remove dust from the cabinet of your IA-8DSP, use a feather duster or a lint-free
soft cloth. To remove dirt and fingerprints, we recommend isopropyl alcohol and a
soft cloth. Dampen the cloth with alcohol first and then lightly clean the surface of the
IA-8DSP with the cloth. Do not use excessive amounts of alcohol that might drip off
the cloth and into the IA-8DSP.
CAUTION! At no time should liquid cleaners be applied directly to the IA-8DSP, as direct application
of liquids may result in damage to electronic components within the unit.

IA-8DSPDSP
18
WISDOMAUDIO.COM
North American Warranty
When purchased from and installed by an authorized Wisdom Audio dealer, Wisdom
Audio electronic products are warranted to be free from defects in material and
workmanship under normal use for a period of five years from the original date of
purchase.
During the warranty period, any Wisdom Audio component exhibiting defects in
materials and/or workmanship will be repaired or replaced, at our option, without
charge for either parts or labor, at our factory. The warranty will not apply to any
Wisdom Audio component that has been misused, abused, altered, or installed and
calibrated by anyone other than an authorized Wisdom Audio dealer.
Any Wisdom Audio component not performing satisfactorily may be returned to the
factory for evaluation. Return authorization must first be obtained by either calling or
writing the factory prior to shipping the component. The factory will pay for return
shipping charges only in the event that the component is found to be defective as
mentioned above. There are other stipulations that may apply to shipping charges.
There is no other express warranty on this component. Neither this warranty nor any
other warranty, express or implied, including any implied warranties of merchantability
or fitness, shall extend beyond the warranty period. No responsibility is assumed for
any incidental or consequential damages. Some states do not allow limitations on how
long an implied warranty lasts and other states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not
apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state. This warranty is applicable in North America only. Outside of
North America, please contact your local, authorized Wisdom Audio distributor for
warranty and service information.

IA-8DSPDSP
19
WISDOMAUDIO.COM
Obtaining Service
We take great pride in our dealers. Experience, dedication, and integrity make these
professionals ideally suited to assist with our customers’ service needs.
If your Wisdom Audio loudspeaker must be serviced, please contact your dealer. Your
dealer will then decide whether the problem can be remedied locally, or whether to
contact Wisdom Audio for further service information or parts, or to obtain a Return
Authorization. The Wisdom Audio Service Department works closely with your dealer
to solve your service needs expediently.
IMPORTANT! Return authorization must be obtained from Wisdom Audio’s Service
Department BEFORE a unit is shipped for service.
It is extremely important that information about a problem be explicit and complete.
A specific, comprehensive description of the problem helps your dealer and the
Wisdom Audio Service Department locate and repair the difficulty as quickly as
possible.
A copy of the original bill of sale will serve to verify warranty status. Please include it
with the unit when it is brought in for warranty service.
WARNING! All returned units must be packaged in their original packaging, and the
proper return authorization numbers must be marked on the outer carton for
identification. Shipping the unit in improper packaging may void the warranty, as
Wisdom Audio cannot be responsible for the resulting shipping damage.
Your dealer can order a new set of shipping materials for you if you need to ship your
loudspeaker and no longer have the original materials. There will be a charge for this
service. We strongly recommend saving all packing materials in case you need to ship
your unit.
If the packaging to protect the unit is, in our opinion or that of our dealer, inadequate
to protect the unit, we reserve the right to repackage it for return shipment at the
owner’s expense. Neither Wisdom Audio nor your dealer can be responsible for
shipping damage due to improper (that is, non-original) packaging.

IA-8DSPDSP
20
WISDOMAUDIO.COM
Specifications
All specifications are subject to change at any time, in order to improve the product.
•Rated power output per channel, from 20 Hz–20 kHz at <1.0% THD
o250 w/ch continuous rms power @ 4Ω;
o125 w/ch continuous rms power @ 8Ω;
oMinimum Impedance: 2Ω
•Signal to Noise ratio: –110 dB (ref 1V rms, A-wtd.)
•Frequency Response: 5Hz –45kHz, +0/-0.5dB
•Dynamic Range: 120 dB
•Voltage gain: >30 dB
•Input sensitivity: 1.2V for full output
•Input impedance: 25 kΩ(balanced)
•Polarity: Non-inverting, Pin 2 positive
•Output impedance: Less than 0.05Ωfrom 20–20,000 Hz
•DSP Signal Processor: 96kHz Analog Devices, 32 Bit Processor
•DANTE/AES67 Input: 8 Channel Input (44.1kHz up to 192kHz sampling at 24bit)
•User DSP: 10 Band PEQ/Filter, Delay and Gain x 8 Channels
•Speaker Driver Management: Up to 8th Order Crossover, FIR and IIR Filters, Delay
•Input Routing Matrix: 16x8
•System Setup: Internal Web server page Wizard UI
•Thermal load: 7 BTU/minute or less [preliminary]
•Mains Voltage: 100V-120V @ 15A; 220V-240V @ 12A; 50hz-60hz
•Removable Power Cord: IEC 320-C19 Mains Socket
•Power consumption: 10W (±5%) [preliminary] at idle and 0.5W (±5%) in standby
•Operating Temperature: 41 °F - 95 °F (5 °C - 35 °C)
•Environmental Conditions:
oTemperature: 0°C - 40°C / 32°F - 104°F
oHumidity: 20% - 80% relative humidity (without condensation)
•Error Monitoring:
oPer Channel Clipping and Temperature
oPower Supply Over/Under Voltage and Temperature
oEvent Monitoring and Download through Web-page Wizard UI
•Dimensions HxWxD: 3.75” x 17” x 13.63” (8.57cm x 43.2cm x 34.7cm)
•Weight: 19 lbs (8.6kg)
•Shipping Weight: 25 lbs. (11.5 kg)
•Shipping Dimensions: 25”x 20”x 9”(63.5cm x 50.8cm x 22.8cm)
Table of contents
Other Wisdom Amplifier manuals
Popular Amplifier manuals by other brands

Little Labs
Little Labs MONOTOR Operator's manual

Steren
Steren AMP-020/GTR user manual

AUSTRALIAN MONITOR
AUSTRALIAN MONITOR Digipage JR Installation & operation manual

FONESTAR
FONESTAR MPA-120 instruction manual

DR. Z Amplification
DR. Z Amplification DB4 ZA-40 instruction manual

Peavey
Peavey VMP 2 operating guide