Wise Controls TVLink RS868 Series User manual

1
DateCode Number: Series Model number Draft
TVLink RS868    T387.01 21-09-09
TVRRL868A02PMR
DIGITAL RADIO CONTROL SYSTEM TVRRL868A02P
EN
ATTENTION!
The subject appliance must be installed only by qualied technical
personnel in compliance with the standards. All connections must be
rated for a single-phase power supply of 230V. For the disconnection from
the power line, use an all-pole switch with contact with an opening of at
least 3,5mm. Only suitable materials for the connections must be used to
guarantee insulation that complies with current standards on the subject
of electrical safety. The programmer carries out movement commands by
radio; all the necessary safety devices are to be seen to separately.
Thedevice’ssignalreceptioncouldbedisturbedbyseveralfactorssuchas:
-thepresenceofelectricalfrequencynoisebeingtransmittedbyother
appliancesworkinginthesameenvironmentandonthesamefrequency.
-appliancesinstalledincontainerswithmetalparts;onlyusecontainersmade
ofplastic.
1- GENERAL DESCRIPTION
Receiverfortheremotecontrolofappliancesuptoamaximumresistive
powerof1000WwithON/OFForimpulsivefunctionandcompatiblewiththe
TVLinksystem.
Thecommandswhicharesentbytransmittercanbe:
-single(everychannelactivatesanddeactivatestheload,ON/OFFor
impulsive)
-inpairs:
Channelpair1,2:channel1-ONandchannel2OFF
Channelpair3,4:channel3-ONandchannel4OFF
Channelpair6,7:channel6-ONandchannel7OFF
ThespecicTVLINKcodesareencodeddirectlybythemanufacturerinside
anEEprommemorymodulethatmaintainstheinformationevenincaseof
blackouts.Theyarealsoprintedontheproductlabelsotheycanbeinsertedinto
theTVLINKdevice.Thesecodescannotbecancelledormodiedastheyarean
integralpartofthereceiver.
Thestandardradiocontrolcodescanbeinserted(memorized)orcancelledin
thereceiverbypressingabuttonthroughasmallholelocatedtoonesideofthe
aerial(seepicture1)
Thecodetransmissiontypeis“Rolling-code”.Thecodeischangedforevery
transmissionthroughtheuseofanalgorithmthatonlythereceiverisableto
recognize.
Themaximumnumberofmemorisationsthatcanbeexecutedis42.
1.1- How to modify the function of the receiver (ON/OFF, impulsive)
InordertomodifythefunctionofthereceiverfromON/OFFtoimpulsive(and
vice-versa),itisnecessarytocarryoutthefollowingprocedure:
1)switchoffthepowersupplyofthereceiver
2)pushandkeeppushedtheinternalpush-buttonP1,switchonthepower
supply(thebuzzerwillemitacontinuoussound).After5seconds,an
intermittentsoundwillindicatethatthefunctionofthereceiverhasbeen
changed.
2- Transmitters
Thetransmittersareencodedinthefactoryandeachtransmitterhasitsown
uniquecode.
Caution!Ifyoukeepachannelbuttonpresseddownformorethan30seconds
thetransmitterwillautomaticallyswitchoff.
ThereceiveriscompatiblewithalltransmittersoftheTVLinkrange:TVTXV,
TVTXP,TVTXC,TVTXK,TVTXQ,TVTXL,TVTXS,TVTXW,TVTXM.
3- ATTENTION: The rst transmitter can only be memorized using
the receiver (you are advised to cancel the entire memory content at the
beginning of each installation by pressing the P1 button).
3.1- Memorisation single channel
Thechannelsch1,ch2,ch3,ch4...willbememorisedonebyone.
1-PressandholddownthepushbuttonP1ofthereceiver,thebuzzerwillsound
continuously.
2-Transmitthechannelwhichistobememorised,oncethechannelis
memorised,thebuzzerwillsoundintermittently,releasethepushbutton.
Repeatpoints1and2tomemoriseulteriorchannelsfromreceiver.
Seeparagraph4tomemoriseulteriorchannelsfromtransmitter.
3.2- Memorisation couple of channels
Thechannelsch1,ch2andch3,ch4andch6,ch7willbememorisedincouple.
1-Presstwo timesandholddownthepushbuttonP1ofthereceiver,thebuzzer
willsoundcontinuously.
2-Transmitoneofthecoupleofchannelwhichistobememorised,once
thechannelismemorised,thebuzzerwillsoundintermittently,releasethe
pushbutton.
Repeatpoints1and2tomemoriseulteriorchannelsfromreceiver.
Seeparagraph4tomemoriseulteriorchannelsfromtransmitter.
WiseHouse,21LyddenRoad,Wandsworth,London,SW184LT
Telephone:02088742234 Fax:02088712262
www.wisecontrols.com  [email protected]
WISE
CONTROLS
4- How to insert a transmitter via radio without having to access the
receiver by means of an already memorized transmitter (memory indexing
procedure)
Thetypeofmemorisationofthechannels(single,couple)dependsonhowthe
channel,whitchisusedinpoint2,hasbeenmemorized.
1)PressthebuttonP3locatedinsidethealreadymemorizedtransmitter.The
enabledreceiversoundcontinuouslyfor5seconds.
2)Transmitachannelpresentinthememoryofthereceiver,inwhichthenew
codeistobememorized,within5secondsandthebuzzerwillinterruptthe
soundfor1sec,andthencarryonforanother5seconds.
3)Transmitthenewchanneltobememorizedwithin5secondsandonce
memorizedthebuzzerwillsoundintermittently.
Toinsertothertransmittersanothercoderepeatoperations1,2and3
Ifthereceiver’smemoryisfullitcannotbeenabledandthiswillbeindicated
bythebuzzerB1soundingintermittently.
5- To cancel a code from the receiver:
1)pressthreetimesandthenholddownthebuttonP1andthebuzzerwillsound
intermittentlyandslowly.
2)pressthechannelwhichistobecancelled,onceithadbeencancelledthe
buzzerwillsoundcontinuously.Inthecase,thechannelhasbeenmemorizedin
pairs,thisoperationcancelsbothchannels.
5.1- To cancel a code from via radio:
1)pressthreetimesandthenholddownthebuttonP3within5secondsandthe
buzzerwillsoundintermittentlyandslowly.
2)pressthechannelwhichistobecancelled,onceithadbeencancelledthe
buzzerwillsoundcontinuously.Inthecasethechannelhasbeenmemorizedin
pairs,thisoperationcancelsbothchannels.
5.2- To cancel all codes in memory:
1)pressthebuttonP1fourtimesandholddownforatleast10seconds(during
thisperiodthebuzzerwillsoundintermittentlyandrapidly)untilthebuzzerwill
soundcontinuously.Releasethebutton.
6- Full or empty memory
Ifthememoryofthereceiverisfullorempty,thebuzzerwillmake3bipboth
duringthememorisationandaftertheresetofthereceiver.
6.1- Errors during the memorising or deleting
Ifthecodehasn’tbeenmemoriseditcouldbeduetothefollowingreasons:
-thememoryisfull.Inthiscasethebuzzerwillsoundintermittentlyandslowly
for3secondseachtimeitisswitchedon,
-theindexingprocedurehasnotbeencorrectlystartedup,
-thecodealreadyexistsinmemory.
Ifthecodehasn’tbeencancelleditcouldbeduetothefollowingreasons:
-thecodedoesn’texistinmemory.
7- TECHNICAL SPECIFICATIONS
Receptionfrequency   868.3MHz
Intermediatefrequency   10.7MHz
Sensitivity(nelytunedsignal)  1µV
Powersupply    230Vac
Consumption    0.5W
Maximumcommutablepowerattherelay:
withresistiveload    8A250Vac
     8A30Vdc
Operatingtemperaturerange   -20°÷+60°C
Intheviewofaconstantdevelopmentoftheirproducts,themanufacturer
reservestherightforchangingtechnicaldataandfeatureswithoutpriornotice.

2
5
6
7
P3
C H2
C H4
C H3
C H1
(P 3)
P1
L.
N.
LINE 230V
TVTXP868A01-02-04
TVTXC868A04
ANTENNA
Relaycontactoutput
CH1
CH2
CH3
CH4
TVTXW868A01-02-04-42
CH1 CH2
CH3
CH4
CH1
CH1
CH2
(P3)
CH1
CH2
CH3
CH4
CH5
CH6
CH7
TVTXQ868A07/42
CH1
CH2
CH3
CH4
CH5
CH6
CH7
SEL
SEL