WOHOME LY135 User manual

INSTRUCTION MANUAL
Baby Monitor
Thank you for purchasing our baby series products. We kindly recommend you to
read the following instructions before using this product.

FCC WARNING
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution:Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure
requirement.
The distance between user and products should be no less than 20cm.

WARNING
1. Please keep the product away from the baby more than 3feet
(1meter).
2. Please place the product in a dry place to prevent short circuit
caused by damp.
3. Please use Ac adapter(s) provided by us only. We do not
recommend to use Ac adapters and charging cables from other
brands.
4. This product is not medical equipment. Check your baby's
activities regularly as this product is not designed for supervision
but for assisting your supervising.
PACKING LIST
①Monitor
②Camera
③Monitor AC power Adapter
Manual
④Camera AC power Adapter
⑤Mount kit
⑥User Manual
① ② ③
④ ⑤ ⑥

CAMERA STRUCTURE
①
②
③
④
⑤
⑥
⑦
⑧
⑨
①Power indicator
②Camera Lens
③IR Led
④Night Vision Sensor
⑤Microphone
⑥Temperature sensor
⑦Speaker
⑧Pair button
⑨DC interface
MONITOR
OK
+
③
④
⑤
⑥
⑨ ⑩
②
⑦
⑧
11
①
12

1. Power /Sleep: Long press to turn on/off the monitor.
Short press to turn on /off the screen.
2. Menu/Black: Press to enter menu page or press as a Back button.
3. Up: Press to shortcuts for adding brightness (Live video).
Press to change your selection upward (Menu setting).
4. Down: Press to shortcuts for subtracting brightness (Live video ).
Press to change your selection downward (Menu setting).
5. Left: Press to shortcuts for play lullabies (Live video).
Press to change your selection leftward (Menu setting ).
6. Right: Press to shortcuts for Zoom in /out (Live video).
Press to change your selection rightward (Menu setting).
7. OK/Camera Switch: Press to confirm your selection or switch
cameras if connected with 2 or more
cameras.
8. Talk: Press to talk to your baby in the monitoring image.
9. Charging Indicator: It gives off red light while the monitor is
being charged.
10. Power Indicator: The green light turns on if connected to
electricity.
11. Microphone.
12. Volume Button: Press to adjust the monitor’s volume in the
monitoring image.

13
14
16
15
17
2.5mm DC charging head
Display bracket
Speaker
13
14
15
Antenna
Reset hole
16
17
STATUS BAR ICON DESCRIPTION
:
2:30
① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

①Signal strength
②Temperature
③Camera connected
④Alarm prompt
⑤Feeding
⑥Lullaby
⑦Camera cycle time
⑧Sound sensitivity
⑨Date/time
⑩Battery capacity
HOW TO USE?
Getting started
Step1:
1. Connect the camera to the AC adapter(2.5mm).
2. Plug the AC adapter into a socket.
Note: Place the camera away from your baby 3ft/1m at least.
Step2:
1. Connect the monitor to the AC adapter(3.5mm).
2. Plug the AC adapter into a socket.
Note: The monitor takes about 3 hours to be fully charged, and it
lasts about 4hours.
Step3:
Long press the power button to turn on the monitor then you can see
the monitoring interface.
Note: The camera and monitor were paired already before you get
them. So you don’t need to pair them.

CAMERA SETTING
This function is to add a new camera to the monitor.
a. Press button enter to the
menu page. Select and
press OK to enter camera
settings.
b. Select and press Add Camera
OK button.
c. Pop up pairing interface .
Countdown 60sec.
d. Press the button on the Pair
back of the camera.Then see
the camera added successfully.
Note: Four cameras at most can be connected to one monitor.
Cycle Cameras
Delete Camera
Add Camera
CAMERAS
Add Camera
1. A d d cam e ra
Add Camera

a. Press enter menu page.
Select and press OK to
enter camera settings.
b. Press to select the
Delete Cameraand press OK.
c. Press or to select the
camera you need to delete.
Press OK to confirm you
choose.
d. Select the option and Delete
go to delete your camera. Use
button to select to Cancel
return to the superior menu.
Delete Camera
Cycle Cameras
Delete Camera
Add Camera
CAMERAS
Camera 3
Camera 2
Camera 1
Camera 4
Camera 1
Cancel
Delete
2. D e l et e C ame r as

This function is setting the time for switch one camera to another
camera if connecting multiple cameras.
a. Press enter menu page.
Select and press OK to
enter camera settings.
b. Press to select the
Cycle Cameras and press OK.
c. Choose the time you want.
Press OK to confirm.
Cycle Camera
Cycle Cameras
Delete Camera
Add Camera
CAMERAS
10 Sec
5 Sec
OFF
15 Sec
30 Sec
3. C y cle C a mer a s
SL EE P MO DE
This function is to prolong your monitor’s run time by shutting down
the screen.

CAM ERA S SLE EP MODE
a. Press to enter menu page.
Select . Press OK to enter
the setting.
b. Select OFF to turn off
Sleep Mode. Press or
button to select the time you
want. Press OK to confirm.
c. Press to back to menu interface.
Sleep Mode: 3 min
Sleep Mode: 1 min
Sleep Mode: off
SLEEP MODE
Sleep Mode: 5 min
TE MP /S OU ND A LE RT
1. T e mp Ac t iva t ed Al e r t
This function is to send alarms if the temperature exceeds your
settings.
a Press to enter menu .
page. Choose and press OK.
b Selectthe.
Temp Activated Alert
and press OK.
CAME RAS S LEEP MO DE TEM P/SOU ND ALER T
VOX Senstivity
Temp Activated Alert
TEMP/SOUND ALERT

c. High temperature setting.
Select the option you want.
Press OK to confirm.
d. Low temperature setting.
Select the option you want.
Press OK to confirm.
e. Alert Duration setting. Select
the time you want.Press OK to
confirm.
75°F
off
80°F
85°F
90°F
Low Temp
High Temp
Temp Activated Alert
Alert Duration
Low Temp
High Temp
Temp Activated Alert
Alert Duration
70°F
off
65°F
60°F
55°F
Low Temp
High Temp
Temp Activated Alert
Alert Duration
10 Sec
5 Sec
20 Sec
30 Sec
2. V O X Sen s i ti v i ty
Sound Level
There are six options of sound detection,off,1-5. OFF means you
shut down the function.1 means the sound sensitivity is the
highest and so on for Medium and Lowest(5 sensitivity).
a. Press to enter menu page.
Press button to select the
and press OK.Vox sensitivity
VOX Senstivity
Temp Activated Alert
TEMP/SOUND ALERT

Sound Level
VOX Senstivity
Alert Duration
b. Sound level setting.1-5 levels
of sensitivity you can choose.
Press OK to confirm you want
select one.
Alert Duration
a. Press to enter menu page.
Choose the Alert Duration
option and press OK.
b. There are four options of alarm
time you can choose. Press
or to choose the right time
and press OK to confirm.
Note: The alert interval time is 1 minute (default value). It will alarm
again after every 1 minutes when the sound is detected. The
alert duration can adjust to 5s-30s.
2
3
4
5
1
Off
Low Temp
High Temp
Temp Activated Alert
Alert Duration
10 Sec
5 Sec
Alert Duraon
20 Sec
30 Sec
TI ME S ET
1. S e t Tim e
This function is to set Date/Time,turn on /off OSD. The real time
you set that will be displayed on the status of the monitor if you
turn on OSD.

a. Press to enter menu page.
Choose enter the settings.
b. Select and press OK Set Time
to enter the next interface.
c. Press or to choose the ON
or OFF. ON stands for starting
the setting.
d. Use , , , button to
change the Date/time settings.
Press OK to finish setting.
CAME RAS S LEEP MO DE TEM P/SOUN D ALERT TIM E SET
+
2. F e ed Ti m er
This function is to remind you of feeding your baby. Off means you
shut down the function.2.5H hour means remind you every 2.5 hour
and so on for other options.

a. Press to enter menu page.
Choose enter the Feed Timer
setting.
b. Choose the time you want.
Select Off to turn off the
feeding reminder.
Note: Feeding alarm lasts 5 second.
CAM ERAS S LEEP MO DE TEM P/SOUN D ALERT TI MESE T
BRI GHTN ESS
BR IG HT NE SS
This function is to set the brightness of monitor screen.
a. Press to enter menu page.
Choose enter the interface.
b. Use , button to adjust the
brightness.
Note: The higher the brightness, the higher the power consumption.
Ithas an impact on the working time of the monitor.
BRI GHTN ESS

LU LL AB IE S
CAM ERAS S LEEP MO DE TE MP/SOU ND ALER T TIME SET
BRI GHTN ESS LU LLAB IES
LULLABIES
Lullaby1
Lullaby2
Lullaby3
Lullaby4
Lullaby5
Lullaby6
PlayAll
This function is to comfort your baby when needed.
a. Press to enter menu page.
Choose enter the interface.
b. Use , button to select the
lullaby you want. Choose
Play All to play the lullabies in
a loop.
Note: Lullaby function has a quick open mode. When in Live video
you can turn the lullaby on or off using the shortcut button.
ZO OM
This function is to Zoom in/out image to facilitate the observation
of baby's life details.
a Press to enter menu page. .
Choose enter the interface.
CAM ERAS S LEEP MO DE TE MP/SOU ND ALER T TIME SET
BRI GHTN ESS LU LLA BIES ZO OM

b. Select 1.5x or 2x you want.
Press OK to confirm.
Note:The Zoom function also has a quick open mode. When in
Live video, you can Zoom in/out image using the shortcut
button.
ZOOM
off
1.5x
2.0x
CAM ERAS S LEEP MO DE TE MP/SOU ND ALER T TIME SET
BRI GHTN ESS LU LLA BIES Z OOM SE TTI NGS
+
SE TT IN G
This function is to set Night Vision Mode, Anti-Screen Flicker,
Default Settings and provide service support information.
1. Ni g h t Vi s i on Mo d e
a. Press to enter menu page.
Choose enter the interface.
b. Select the camera you want to
turn on/off the
.Night Vision function

2. An t i-S c r een F l ick e r
a. Select and confirm
. Press OK Anti-Screen Flicker
to enter the interface.
b. Power supply frequency of
50Hz or 60Hz can be selected.
Note: Generally 60Hz is selected in the United States, Japan and
other countries. In this way, the picture will not flicker
because of the interference of the power frequency. It's
usually 50Hz in Europe.
3. De f aul t S ett i n gs
a. Select and confirm
. Press OK to Default Settings
enter the interface.

b. Confirm YES to reset. Press
or confirm NO to exit.
4. Te m per a tur e U nit
a.Select and confirm
. Press OK Temperature Unit
to enter the interface.
b. Choose °F or °C you want and
press OK.
5. Ab o ut
Select to enter the About
interface.

6. Co n nec t W ith U s
Select to Connect With Us
enter the interface.
FA Q
Q1. The monitor will alarm when the network is disconnected
a. The monitor will alarm 1 minute when the network is
disconnected. It will alarm again after every 5 minutes, and
so on lasts for 30minutes will automatically turn off.
b. You can press Menu button to turn off the alarm directly.
Q2. The monitor failed to connect to the camera
Please check whether the distance between the camera and
the monitor is within the proper range Please try to move to a
shorter distance and try to pair again.
Q3. Why is the live video so blurry?
Please check and make sure there is no obstacle on the lens
of the camera.
Q4. Noise on the monitor
The camera is too close to the monitor.Please put them further
apart.
Q5. Can I hear my baby when I turn off the screen?