Wood Stone WS-GPL-4836-4-CT User manual

Toll Free 800.988.8103
Tel [phone]
Fax [phone]
www.woodstone-corp.com
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
GAS PLANCHA
Speciality Equipment
Countertop Model
and Optional Stand Models
4-ZONE GAS PLANCHA WS-GPL-4836-4-CT
DOC NO M0202.00 REVISED January 2017
Installation and
Operation Manual

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
2
M0202.00 January 2017
TABLE OF CONTENTS
TABLE OF CONTENTS
PLANCHA � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
CAUTIONS AND WARNINGS � � � � � � � � � � � � � � � � � � � � � � � �4
GPL-4836-4 SPECS - COUNTERTOP MODEL� � � � � � � � � � � �5
GPL-4836-4 SPECS - OPTIONAL STAND MODEL� � � � � � � � �6
CLEARANCES � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �7
UTILITY INFORMATION � � � � � � � � � � � � � � � � � � � � � � � � � � � �8
BASIC OPERATION � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �9
DAILY USE & MAINTENANCE� � � � � � � � � � � � � � � � � � � � � � �10
TROUBLESHOOTING� � � � � � � � � � � � � � � � � � � � � � � � � � � � �11
OPERATIONAL SEQUENCE � � � � � � � � � � � � � � � � � � � � � � � �12
GPL-4836-4 WIRE DIAGRAMS � � � � � � � � � � � � � � � � � � � � �13
LIMITED WARRANTY � � � � � � � � � � � � � � � � � � � � � � � � � � � �19

Gas Plancha Installation and Operation Manual
3
M0202.00 January 2017
Wood Stone’s Gas Plancha has been tested and approved by Intertek,
and is ETL listed to ANSI Z83.11:2016, CSA 1.8b:2016 Ed. 4 and to NSF/ANSI Standard 4 - 2009e.
PLANCHA
WS-PL-4836 4-CT
Shown with optional stand
WS-PL-4836 4-CT
ANSI Z83.11:2016 Ed.4
CSA 1.8:2016 Ed.4
ANSI/NSF STD 4
INSTALLATION AND OPERATION MANUAL
WOOD STONE GAS PLANCHA
WS-GPL-4836-4-CT
WS-GPL-4836-4-CT ON OPTIONAL STAND
ADDITIONAL COPIES AVAILABLE UPON REQUEST

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
4
M0202.00 January 2017
CAUTIONS AND WARNINGS
IF THIS EQUIPMENT IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE,
FOLLOW THESE INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF APPLIANCE-RELATED FIRES IS
FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS
OF UTMOST IMPORTANCE THAT THIS APPLIANCE BE INSTALLED ONLY IN ACCORDANCE WITH THESE
INSTRUCTIONS.
!
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL THE APPLIANCE. FAILURE TO FOLLOW INSTRUCTIONS MAY
RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS
ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
WOOD STONE GAS PLANCHA INSTALLATION AND OPERATION INSTRUCTIONS
DO NOT THROW THIS MANUAL AWAY
RETAIN THIS MANUAL FOR FUTURE REFERENCE
Additional copies of this manual and prompt responses to service/maintenance
questions are available from Wood Stone @ 1-800-988-8103�
FOR YOUR SAFETY: DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY
OF THIS OR ANY OTHER APPLIANCE. ALSO, ALWAYS KEEP THE AREA UNDER AND AROUND THIS APPLIANCE FREE AND
CLEAR OF ANY AND ALL COMBUSTIBLE MATERIALS.
IMPORTANT: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN RESULT IN
PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.
IMPORTANT: CONSULT YOUR LOCAL GAS SUPPLIER FOR A STATEMENT OUTLINING A PROCEDURE TO BE
FOLLOWED IN THE EVENT YOU SMELL GAS. POST THE STATEMENT IN A PROMINENT LOCATION.
WARNING: This product must be installed by a licensed plumber or gas fitter when installed within the
Commonwealth of Massachusetts.
IMPORTANT: IT IS RECOMMENDED THAT THIS EQUIPMENT BE INSTALLED, MAINTAINED AND SERVICED BY
AUTHORIZED PROFESSIONALS.

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
5
M0202.00 January 2017
GPL-4836-4-CT SPECS - CT
Shipping weight: 579 lbs Unit weight: 484 lbs
Plan view
Side viewFront view
GPL-4836-4-CT (4 ZONE) COUNTERTOP MODEL
GPL-4836VisibileControlsNoCart
451/4"
1150mm 21"
530mm
83/4"
220mm 41/4"
110mm
201/2"
520mm
71/2"
190mm
123/4"
330mm
4"
100mm
341/4"
870mm
241/4"
610mm
8"
200mm
48"
1220mm
39"
990mm
21/4"
60mm
G
G
121/2"
320mm
GREASERESERVOIRS
MAINPOWERSWITCH
GPL-4836VisibileControlsNoCart
451/4"
1150mm
21"
530mm
83/4"
220mm
41/4"
110mm
201/2"
520mm
71/2"
190mm
123/4"
330mm
4"
100mm
341/4"
870mm
241/4"
610mm
8"
200mm
48"
1220mm
39"
990mm
21/4"
60mm
G
G
121/2"
320mm
GREASERESERVOIRS
MAINPOWERSWITCH
GPL-4836VisibileControlsNoCart
451/4"
1150mm
21"
530mm
83/4"
220mm 41/4"
110mm
201/2"
520mm
71/2"
190mm
123/4"
330mm
4"
100mm
341/4"
870mm
241/4"
610mm
8"
200mm
48"
1220mm
39"
990mm
21/4"
60mm
G
G
121/2"
320mm
GREASERESERVOIRS
MAINPOWERSWITCH
UTILITIES SPECIFICATIONS
Gas: 3/4 inch FNPT gas inlet
110,000 BTU/hr Natural Gas (NG)
OR
118,000 BTU/hr Propane (LP)
Maximum gas inlet pressure
1/2 psi (14 inches W�C�)
Electrical
120 VAC, �7 A, 50/60 Hz
Equipped with a NEMA 5-15P plug
for use with a standard 120 VAC
15 A or 20 A outlet�
Refer to data plate when installing�
G
Venting
The Wood Stone Gas Plancha must be vented with a Listed
Type 1 exhaust hood, or one constructed in accordance with
NFPA 96 and all relevant local and national codes� The oven
must be vented in accordance with all relevant local and
national codes, and in a manner acceptable to the authority
having jurisdiction�

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
6
M0202.00 January 2017
GPL-4836-4-CT SPECS - STAND
GPL-4836-4-CT (4 ZONE) OPTIONAL STAND MODEL
GPL-4836 Visible ControlsWith Cart
22 1/2"
570mm
42 3/4"
1090mm
16 1/2"
420mm
73/4"
200mm
29 1/2"
750mm
37 3/4"
959mm
35 1/4"
890mm
71/2"
190mm
26 1/2"
670mm
39"
990mm
48"
1220mm
8"
200mm
24 1/4"
610mm
34 1/4"
870mm
21/4"
60mm
G
G12 1/2"
320mm
42 3/4"
1090mm
6"
150mm
11/4"
30mm
MAINPOWERSWITCH
GREASE RESERVOIRS
Plan view
GPL-4836 Visible ControlsWith Cart
22 1/2"
570mm
42
3/4"
1090
mm
16 1/2"
420mm
73/4"
200mm
29 1/2"
750mm
37 3/4"
959mm
35 1/4"
890mm
71/2"
190mm
26 1/2"
670mm
39"
990mm
48"
1220mm
8"
200mm
24 1/4"
610mm
34 1/4"
870mm
21/4"
60mm
G
G12 1/2"
320mm
42 3/4"
1090mm
6"
150mm
11/4"
30mm
MAINPOWERSWITCH
GREASE RESERVOIRS
Side view
GPL-4836 Visible ControlsWith Cart
22 1/2"
570mm
42 3/4"
1090mm
16 1/2"
420mm
73/4"
200mm
29 1/2"
750mm
37 3/4"
959mm
35 1/4"
890mm
71/2"
190mm
26 1/2"
670mm
39"
990mm
48"
1220mm
8"
200mm
24 1/4"
610mm
34 1/4"
870mm
21/4"
60mm
G
G12 1/2"
320mm
42 3/4"
1090mm
6"
150mm
11/4"
30mm
MAINPOWERSWITCH
GREASE RESERVOIRS
Front view
Shipping weight: 660 lbs. Unit weight: 550 lbs.
UTILITIES SPECIFICATIONS
Gas: 3/4 inch FNPT gas inlet
110,000 BTU/hr Natural Gas (NG)
OR
118,000 BTU/hr Propane (LP)
Maximum gas inlet pressure
1/2 psi (14 inches W�C�)
Electrical
120 VAC, �7 A, 50/60 Hz
Equipped with a NEMA 5-15P plug
for use with a standard 120 VAC
15 A or 20 A outlet�
Refer to data plate when installing�
G
Venting
The Wood Stone Gas Plancha must be vented with a Listed
Type 1 exhaust hood, or one constructed in accordance with
NFPA 96 and all relevant local and national codes� The oven
must be vented in accordance with all relevant local and
national codes, and in a manner acceptable to the authority
having jurisdiction�

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
7
M0202.00 January 2017
CLEARANCES
CLEARANCES
1. The Wood Stone Gas Plancha must have a minimum 12 inch clearance to combustible construction from sides and back,
and 0 inch clearance to non-combustible construction from sides and back.
2. This appliance may be installed on a combustible or non-combustible surface�
3� Combustion air: Combustion air flows into the Plancha through vents in the bottom panel� The Plancha must be installed with
the legs provided� Do not block the space between the appliance and the countertop�
IF THIS EQUIPMENT IS NOT PROPERLY INSTALLED A FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE,
FOLLOW THESE INSTALLATION INSTRUCTIONS. A MAJOR CAUSE OF APPLIANCE-RELATED FIRES IS
FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS
OF UTMOST IMPORTANCE THAT THIS APPLIANCE BE INSTALLED ONLY IN ACCORDANCE WITH THESE
INSTRUCTIONS.
!

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
8
M0202.00 January 2017
UTILITY INFORMATION
GAS INFORMATION:
The Wood Stone Gas Plancha is equipped with a 3/4 inch FNPT gas connection located at the rear of the appliance� The installer
should provide an appropriate quick disconnect fitting for connection to the gas supply�
BURNER MANIFOLD PRESSURE
BTU/HR INPUT RATE
The Plancha is equipped with an internal gas pressure regulator� This regulator is not adjustable� If incoming gas pressure is less
than 1/2 psi (14 inches W�C�), no external regulator is required or recommended� If incoming gas pressure is greater than 1/2 psi,
an external regulator, by others, must be installed�
If you must convert the Plancha to run on a different gas type, i�e� NG to LP, please contact Wood Stone to obtain the necessary
parts and instructions�
No modification is required for use at high altitudes�
ELECTRICAL RATINGS
The Plancha is equipped with a NEMA 5-15P plug for use with a standard 120 VAC 15 A or 20 A outlet�
Model Natural Gas (NG) model Propane (LP) model
GPL-4836-4-CT 4�0" W�C� 9�0" W�C�
Model Natural Gas (NG) model Propane (LP) model
GPL-4836-4-CT 110,000 BTU/hr 118,000 BTU/hr
Model Voltage Amperage
GPL-4836-4-CT 120 VAC 0�7 A
Electrical Grounding: This appliance must be electrically grounded in accordance with local codes, or in the absence of local
codes, with the National Electrical code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22�1 as applicable�
ELECTRICAL SUPPLY CORD AND GAS CONNECTION SHOULD BE ROUTED SO THAT THEY ARE NOT SUBJECTED TO THE HEAT
COMING FROM THE PLANCHA COOKING SURFACE.
VENTILATION
The Wood Stone Gas Plancha must be vented with a Listed Type 1 Exhaust Hood, or one constructed in accordance with NFPA 96
and all relevant local and national codes� The oven must be vented in accordance with all relevant local and national codes, and in
a manner acceptable to the authority having jurisdiction�

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
9
M0202.00 January 2017
CLEAN THOROUGHLY BEFORE FIRST USE
A vegetable oil cooking spray is applied to the cook surface at the factory to help protect from corrosion during shipping� The cook
surface must be thoroughly cleaned before use� Follow these instructions:
1. Make sure the Grease/Debris Trays are in place�
2. Turn the Plancha ON and allow to heat for 5 minutes� Then turn the Plancha OFF and wait for 5 minutes�
3. Wipe the cook surface using a wet towel, dampened with a small amount of water and a mild dish detergent� Then rinse with a
towel dampened with clean water 3-4 times� Wipe the surface down with a dry towel and the Plancha is ready for service�
CAUTION: THE COOKING SURFACE WILL BE HOT! USE CAUTION WHEN WIPING SURFACE,
PAYING PARTICULAR ATTENTION TO AVOID STEAM FROM DAMP TOWELS.
BASIC OPERATION
Use the Power Switch on the Front Panel to turn on the Plancha� This appliance utilizes an automatic ignition system—there are no
standing pilots to manually light� Press the Power Switch to the OFF position to turn off the Plancha�
At start-up, the red RESET light next to the Power Switch will be illuminated until the automatic ignition system has successfully lit
the pilot� This is typically not more than a few seconds� However, when initially starting the unit up after installation, pilot ignition
will likely take longer while air in the gas line purges—the light will remain illuminated until the pilot lights� NOTE: If the red
RESET light illuminates during operation of the Plancha, turn the power switch to the OFF position, wait 5 minutes, then restart the
Plancha�
When the Plancha is first turned on the Heat Indicator Light for each zone will be illuminated until its zone reaches the
temperature set on the Temperature Control Knob (appx 18–20 minutes)� After the set temperature has been reached, a Heat
Indicator Light will only illuminate when the temperature of its corresponding zone has dropped below the temperature set on the
Temperature Control Knob� For example, an Indicator Light may illuminate after a large food load is placed on the cooking surface�
The Plancha Controller automatically adjusts the runtime of the burners suppling heat to each zone to maintain the set point
temperature�
BASIC OPERATION
ON/OFF switch
Red RESET light
4 Heat
Indicator Lights
Grease/debris trays
PL-4836-4-CT

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
10
M0202.00 January 2017
DAILY USE & MAINTENANCE
DAILY USE AND MAINTENANCE
1. Check and empty the Grease/Debris Trays frequently throughout the day� Keep the drain clear and do not allow the trays to
overflow�
2. The cooking surface should be scraped periodically throughout the day� To remove loose debris use a dry towel�
CAUTION: COOK SURFACE IS VERY HOT!
3. When using chemicals to clean the grill surface, first shut down the Plancha and allow it to cool� If the Plancha is too hot, the
chemical may tend to boil or burn off immediately and not work as effectively� Do not pour water onto a hot Plancha to cool it
as this can warp the cook surface�
DO NOT USE EXCESSIVE AMOUNTS OF WATER TO CLEAN THE PLANCHA. Be careful when using scrapers on the cook
surface to avoid scratching or gouging the top� Be aware that the cook surface is made of mild steel—it will not clean to
a shiny silver-like surface� Do not use heavy duty degreasers or oven cleaners on the Plancha as these are not generally
intended for use on hot surfaces�
Damage caused by using spray hoses or excessive water, or scratching or marring of the cook surface, is not covered by the
warranty�
4. The front, sides, and back may be wiped down with a cloth and mild detergent if needed� Do not use abrasive cleaners or
scouring pads as these will scratch the stainless steel�

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
11
M0202.00 January 2017
TROUBLESHOOTING
1/2
1/2
1/4 1/4 1/4 1/4
4836-4 zone
PROBLEM CAUSE/SOLUTION
Plancha will not turn on� No indicator
light on ON/OFF switch
1. Check that Plancha is plugged in, and that circuit breaker for the circuit serving
the Plancha has not tripped� Power for the Plancha may be interlocked to the
ventilation system—make sure the exhaust hood system is turned on�
2. If Plancha still does not turn on, please contact Wood Stone for assistance�
Red RESET light comes on
Grill is not cooking consistently
1. Check that gas line is connected by disconnecting and reconnecting the gas
line, and that all gas shutoffs are in the open position� Gas supply may be
interlocked to the ventilation system —make sure exhaust hood is turned on�
To retry, turn off Plancha, wait 5 minutes, then turn back on�
2. If the Plancha is being started for the first time: Make sure all air has been bled
from the gas line�
1. Determine the cooking surface temperature, using the Surface Temperature
Measurement Procedure below�
2. If any reading is outside the acceptable temperature range, call Wood Stone�
Please contact Wood Stone at 1-800-988-8103 should service be necessary, or if you have any questions about your
Plancha. Our service hours are 8 am to 5 pm Pacific Time. Follow the recorded instructions for Emergency Service
if you require assistance during non-business hours. A Wood Stone technician will promptly respond to your call.
SURFACE TEMPERATURE MEASUREMENT PROCEDURE
1. From a cold start: Turn on the Plancha and wait at least 70 minutes before
taking temperature measurements�
If Plancha is heated up / in use: Allow 15 minutes of inactivity to stabilize
after last cooking run� Make certain grill surface is clean�
2. Carefully set the Temperature Knobs to exactly 500 °F�
3. Take temperature measurements using a surface probe� Note measurement
once reading has stabilized� Measurement points • are shown on the
diagram at left—one at the center of each zone�
4. Temperature reading at each point should be within the range 490-540 °F�

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
12
M0202.00 January 2017
OPERATIONAL SEQUENCE
SEQUENCE OF OPERATION
Based upon the temperature
of each of the four zones as
compared to the Set Point,
individual Burners are
ON or OFF�
Burners light�
Controller determines
temperature is below Set Point
and signals Burners to light�
Green front panel lights
illuminate�
Software version blinks on one of
the green front panel lights, and
momentarily illuminates the red
"Fault" light�
Burner(s) do not light� After 3 attempts, Gas
Valve closes and red Fault light illuminates�
No additional attempts at relighting until
Main Power is turned OFF, then ON to reset�
Power Switch ON�
Power OFF� All Gas Valves
close� All Burners and
Controller OFF�

Gas Plancha Installation and Operation Manual
13
M0202.00 January 2017
GPL-4836-4 WIRE DIAGRAMS
DATE:
DIAG #:
WD410 Rev. 0
1/25/2017
WS-GPL-4836
Bellingham, WA [phone] www.woodstone-corp.com
Sheet: 1 of 4
\\woodstone\dfs\CAD\0 Pn\W_Wiring\WD_Wiring_Diagrams\WD400-WD499 Planchas\WD410_WS-GPL-4836_4_Knob_Gas_Plancha-0.dft
2nd Generation - 4 Knob
Alarm +24 -
Z2Z3Z4 Z2Z3Z4 Z2Z3Z4
W6 P2 W6 P3 W6 P4
OR BK
BK
WH/RD
Z2 Z3 Z4
1/4" Q.C.
Z1 - TYP X4 A
+24
Th
Valve-
Burner Gnd
1 2 3
4
5 6
7
8
9
W6P1
Valve+
1234 5678
W6P5
W6 TB1 W6 TB3 W6 TB2
BK
WH/RD
OR
GY/OG
RD
Note Connector Clip Orientation (Wire Side View)
1/4" x 0.032 Q.C.
Gas Valve P/N 7000-1321
Fenwal Ign.
Controller
Woodstone Corp.
P/N 7000-1695
7000-1725 TYP X3
H.V. Suppression Cable 7000-1694
BK
7000-1603
7000-1602
GY/OG
GY/BU
GY/YE
GY/BN
Ignition Module Interconnect Harness - W6
IGNITION MODULE INTERCONNECT HARNESS - W6

Gas Plancha Installation and Operation Manual
14
M0202.00 January 2017
GPL-4836-4 WIRE DIAGRAMS
DATE:
DIAG #:
WD410 Rev. 0
1/25/2017
WS-GPL-4836
Bellingham, WA [phone] www.woodstone-corp.com
Sheet: 2 of 4
\\woodstone\dfs\CAD\0 Pn\W_Wiring\WD_Wiring_Diagrams\WD400-WD499 Planchas\WD410_WS-GPL-4836_4_Knob_Gas_Plancha-0.dft
2nd Generation - 4 Knob
12345678
-+GN
L
PS1
24 VDC 75 W
A2
Buffer Board
J2
1 2 3 4 5 6 7 8 9 10 11 12 J1
J3
1 2 3 4 5 6 7 8 9 10
1
2 3
4
5
6
7 8
9
10
11 12
Woodstone Corp. P/N 7000-1762-1
TB1
W11
A1
J1+
-
J5
10 9 8 7 6 5 4 3 2 1
CPI Board
Woodstone Corp. P/N - See Sheet 3
TB1
LNG
Jumper Terminal 7000-1610
Conduit
Woodstone Corp. P/N 7000-1370
W11
off
off
3
2
14
9
1
3
8
Woodstone P/N 7000-0946-1
S1
3 2 1
3 2 1
S1 Rear Connector Plate
DS5
- Silver
+ Gold
Red, 7000-0897
7000-1725
BK BK
70CE-0029 (1 Full Turn)
70CE-0007 (1/2 Turn)
18 ga
GY/OG
GY/BU
GY/YE
GY/BN
WH/RD
BK
BK
OG
GY/OG
GY/YE
GY/BU
GY/BN
WH/RD
18 ga
1 2 3 4
58
6 7
1
3 48
9
Ignition and Power Distribution
IGNITION AND POWER DISTRIBUTION

Gas Plancha Installation and Operation Manual
15
M0202.00 January 2017
GPL-4836-4 WIRE DIAGRAMS
DATE:
DIAG #:
WD410 Rev. 0
1/25/2017
WS-GPL-4836
Bellingham, WA [phone] www.woodstone-corp.com
Sheet: 3 of 4
\\woodstone\dfs\CAD\0 Pn\W_Wiring\WD_Wiring_Diagrams\WD400-WD499 Planchas\WD410_WS-GPL-4836_4_Knob_Gas_Plancha-0.dft
2nd Generation - 4 Knob
Green, 7000-0895 (X4) DS3
- Silver
+ Gold
DS4
- Silver
+ Gold
1
2
3 4
5
6
7
8
9
10
J2
1
2
3 4
5
6
7
8
9
10
J3
Woodstone Corp. P/N 7000-0891-61
Pot 2 CW (+5v)
Pot 2 Wiper (0 - 5v) Pot 2 CCW (gnd) LED 2 - (switched)
LED 2 + (24)
Pot 4 CW (+5v)
Pot 4 Wiper (0 - 5v)
Pot 4 CCW (gnd)
LED 4 - (switched)
LED 4 + (24)
LED 3 + (24)
LED 3 - (switched)
Pot 3 CCW (gnd)
Pot 3 Wiper (0 - 5v)
Pot 3 CW (+5v)
LED 1 + (24)
LED 1 - (switched) Pot 1 CCW (gnd) Pot 1 Wiper (0 - 5v) Pot 1 CW (+5v)
A1
CPI Board
DS2
-
+
DS1
-
+
RD BU
WH/YE WH/BK WH/RD
BU
RD
YE/BU
RD
BU
GY/BU
PK/YE
PK/OG
GY/YE
BU
RD
150vF - 650vF
150vF - 650vF
R1
R4
R3
150vF - 650vF
R2
150vF - 650vF
GY/OG
YE/RD
YE/BK
PK/BU
Gold
Silver
Gold
Silver
CW
CCW
CW
CCW
CW
CCW
CW
CCW
YE/RD
WH/RD
PK/OG
GY/YE
Indicators and Potentiometers
INDICATORS AND POTENTIOMETERS

Gas Plancha Installation and Operation Manual
16
M0202.00 January 2017
GPL-4836-4 WIRE DIAGRAMS
DATE:
DIAG #:
WD410 Rev. 0
1/25/2017
WS-GPL-4836
Bellingham, WA [phone] www.woodstone-corp.com
Sheet: 2 of 4
\\woodstone\dfs\CAD\0 Pn\W_Wiring\WD_Wiring_Diagrams\WD400-WD499 Planchas\WD410_WS-GPL-4836_4_Knob_Gas_Plancha-0.dft
2nd Generation - 4 Knob
12345678
-+GN
L
PS1
24 VDC 75 W
A2
Buffer Board
J2
1 2 3 4 5 6 7 8 9 10 11 12 J1
J3
1 2 3 4 5 6 7 8 9 10
1
2 3
4
5
6
7 8
9
10
11 12
Woodstone Corp. P/N 7000-1762-1
TB1
W11
A1
J1+
-
J5
10 9 8 7 6 5 4 3 2 1
CPI Board
Woodstone Corp. P/N - See Sheet 3
TB1
LNG
Jumper Terminal 7000-1610
Conduit
Woodstone Corp. P/N 7000-1370
W11
off
off
3
2
14
9
1
3
8
Woodstone P/N 7000-0946-1
S1
3 2 1
3 2 1
S1 Rear Connector Plate
DS5
- Silver
+ Gold
Red, 7000-0897
7000-1725
BK BK
70CE-0029 (1 Full Turn)
70CE-0007 (1/2 Turn)
18 ga
GY/OG
GY/BU
GY/YE
GY/BN
WH/RD
BK
BK
OG
GY/OG
GY/YE
GY/BU
GY/BN
WH/RD
18 ga
1 2 3 4
58
6 7
1
3 48
9
Ignition and Power Distribution
THERMOCOUPLE CONNECTIONS

Gas Plancha Installation and Operation Manual
An ongoing program of product improvement may require us to change
specifications without notice. WS-GPL-4836-CT Gas Plancha [email protected] or visit woodstone-corp.com
Wood Stone Corporation
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
Toll Free 800.988.8103
Tel [phone]
Fax [phone]
19
M0202.00 January 2017
ALL WARRANTY SERVICE MUST BE PRE-APPROVED BY WOOD STONE
PLEASE CONTACT THE FACTORY FIRST
Please call 1-800-988-8103 or 1-360-650-1111 seven days a week. Our normal service hours are 8 am to 5 pm
Pacific time Monday through Friday. If calling during non-business hours, follow the recorded instructions
for emergency service and a Wood Stone technician will get back to you promptly. Wood Stone warrants its
equipment to the original purchaser against defects in material or manufacture for a period of one year from
the original date of purchase subject to the following exclusions and limitations.
EXCLUSIONS:
The warranties provided by Wood Stone do not apply in the following instances:
1. In the event that the equipment is improperly installed� Proper installation is the responsibility of the installer; proper
installation procedures are prescribed by the Wood Stone installation manual�
2. In the event the equipment is improperly maintained� Proper maintenance is the responsibility of the user; proper maintenance
procedures are prescribed in the Wood Stone installation manual�
3. In the event that the failure or malfunction of the appliance or any part thereof is caused by abnormal or improper use or is
otherwise not attributable to defect in material or manufacture�
4. In the event that the appliance, by whatever cause, has been materially altered from the condition in which it left the factory�
5. In the event that the rating plate has been removed, altered or obliterated�
6. On parts that would be normally worn or replaced under normal conditions�
7. Scratches or damage to the grill surface due to improper cleaning or normal wear and tear�
If any oral statements have been made regarding this appliance, such statements do not constitute warranties and are not part of
the contract of sale� This Limited Warranty constitutes the complete, final and exclusive statement with regard to warranties�
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN, ORAL OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE OR WARRANTY AGAINST LATENT DEFECTS
LIMITATIONS OF LIABILITY
In the event of warranty claim or otherwise, the sole obligation of Wood Stone shall be the repair and/or replacement, at the
option of Wood Stone, of the appliance or component or part thereof� Such repair or replacement shall be at the expense of Wood
Stone with the exception of travel over 100 miles or two hours, overtime, and holiday charges which shall be at the expense
of the purchaser� Any repair or replacement under this warranty does not constitute an extension of the original warranty for
any period of the appliance or for any component or part thereof� Parts to be replaced under this warranty will be repaired or
replaced at the option of Wood Stone with new or functionally operative parts� The liability of Wood Stone on any claim of any
kind, including claims based on warranty, expressed or implied, contract, negligence, strict liability or any other theories shall be
solely and exclusively the repair or replacement of the product as stated herein, and such liability shall not include, and purchaser
specifically renounces any rights to recover, special, incidental, consequential or other damages of any kind whatsoever, including,
but not limited to, injuries to persons or damage to property, loss of profits or anticipated profits, or loss of use of the product�
TO SECURE WARRANTY SERVICE
If you claim a defect covered by this Limited Warranty, direct your claim to:
Wood Stone Corporation 1801 W� Bakerview Rd� Bellingham, WA 98226 USA Attn: Global Service Manager
LIMITED WARRANTY

Toll Free 800.988.8103
Tel [phone]
Fax [phone]
www.woodstone-corp.com
WOOD STONE CORPORATION
1801 W. Bakerview Rd.
Bellingham, WA 98226 USA
An ongoing program of product improvement may
require us to change specifications without notice.