Work Hero D10LP User manual

10L DRY CANISTER
D10LP
Designed for:
Motels/Hotels
Garages/Workshops
Cafes/Restaurants
Schools

SAFETY PRECAUTIONS
AND WARNING:
When using your vacuum cleaner, basic
precautions should always be observed,
including the followings;
1. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
2. Children should be supervised to ensure
that they do not play with the appliance.
3. To prevent electrical shock, do not immerse
the appliance, power cord or power plug
into water or other liquids.
4. To prevent electrical shock, do not use the
vacuum cleaner outdoors.
5. Always check the power cord before use,
the power cord and the plug should be in a
good condition and must not be damaged.
If the power supply cord is damaged or
defective, it must be replaced by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
6. Do not unplug by pulling on the power cord.
To unplug, grasp the plug not the power
cord. Use only Australian and New Zealand
electrical safety approved extension cords.
7. Do not pull or carry the appliance by the
power cable, use the power cable as a
handle or pull the power cable around
shaft edges or corners. Avoid running the
appliance over the power cable.
8. Ensure the appliance is switched o
before unplugging.
9. Do not handle or operate the appliance
with wet hands and follow electrical safety
precautions at all times.
10. Extreme caution should be exercised when
using the appliance on stairs.
11. Do not attempt to change the attachments
while the appliance is plugged in to mains
power supply. Switch o and remove
plug from mains power supply. Use only
manufacturer’s recommended accessories.
12. Do not operate the vacuum cleaner too
close to the heaters, radiators and other
hot surfaces.
13. Do not use the appliance to pick up
ammable items or combustible liquids
(i.e. petrol, hot ashes cigarettes, matches,
explosive materials or anything burning)
or use in areas where such substances and
items may be present.
14. Do not use the appliance to pick up toxic
materials (i.e. chlorine bleach, ammonia).
15. Ensure the appliance is disconnected from
the main power supply before connecting
the hose to the unit.
16. Do not operate or use the appliance
without dust bag and/or lters in place
while dry vacuum cleaning.
17. Before vacuuming, remove any large or
shaft objects from the oor or cleaning
surface in order to prevent damage to
the lter.
18. If the air inlet, oor head or the telescopic
tube is blocked, switch o the cleaner straight
away and remove from the main power. First
clear the blocked object before attempting to
start the cleaner vacuum again.
19. Do not leave the appliance unattended when
it is connected to a mains power socket.
20. Before carry out any maintenance service
or cleaning the lters, always switch o the
vacuum cleaner and disconnect the plug
from power supply.
21. Keep ends of the hose, telescopic tube
and other openings away from your face
and body.
IMPORTANT
Always switch o the cleaner and remove the plug from the mains power supply before cleaning
your appliance, when not in use or attempting any maintenance task. The cleaner must only be
connected to an AC power supply at the voltage shown on the rating label. This cleaner should only
be used for its intended purpose as described in this instruction manual.

WORK HERO 10L DRY CANISTER – D10LP 01
1. Do not operate the vacuum cleaner too close to heaters, radiators, and
other hot surfaces.
2. Before inserting the plug into the wall, make sure your hand is dry.
3. Before turning on the vacuum cleaner, remove any large or sharp objects
from the oor or cleaning surface in order to prevent damage to the lter.
4. When you want to pull the plug from the wall, do not unplug by pulling on
cord. To unplug, grasp the plug, not the cord.
5. If the air inlet or oor head or tube are blocked, you should switch o the
cleaner straight away and remove from mains power. First clear the blocked
substance before attempting to start the vacuum cleaner again.
BEFORE YOU BEGIN
22. Do not use the vacuum cleaner if it
is damaged or breaks down. Check
the electrical regularly for defects. If
connection cables, electrical hoses,
electrical contacts and electric tubes are
damaged, have them replace immediately.
23. Never clean the vacuum cleaner or any of
the electrical parts, especially the electrical
connections with water or liquid cleaners.
24. Never attempt to make any modications
electrically to the vacuum cleaner.
25. Always store the appliance indoors in a
cool and dry place.
26. Damage caused by improper use or by not
observing the instructions in this manual
will void warranty.

02 WORK HERO 10L DRY CANISTER – D10LP
KNOW YOUR PRODUCT
1. Handle
2. Hose
3. Three-piece metal tube
4. Hose Inlet
5. Carry Handle
6. On/O Switch
7. Connection Latches
8. Wheels
9. Tank
10. Combination Floor Tool
11. Cloth Filter (not shown)
12. Power Cable/Cord Restraint
13. Crevice Tool
14. Dusting Brush
14. Dusting
Brush
1. Handle
2. Hose
3. Three-piece
metal tube
10. Combination
Floor Tool
11. Cloth Filter (not shown)
12. Power Cable/
Cord Restraint
6. On/O Switch
4. Hose Inlet 5. Carry Handle
8. Wheels
9. Tank
7. Connection
Latches
13. Crevice
Tool

WORK HERO 10L DRY CANISTER – D10LP 03
02 WORK HERO 10L DRY CANISTER – D10LP
ASSEMBLY AND USE
The cleaner should be switched o and disconnected from the mains power supply before you
start to assemble.
Part 1
1. Connect the 3-piece metal tube together.
2. Connect the handle on the hose to the tube.
3. Connect the tube to the combination oor tool or the crevice tool/dusting brush.
Part 2
1. Disconnect latches on side of machine and remove the canister lid.
2. Remove all accessories from inside the tank.
3. Fit the wheels to the base of the tank. Install the big wheels into the relevant positions and
then x with screws included. (Note wheels are marked “R” and “L” to help installation).
4. Replace the canister lid (with the power cord facing the opposite direction of the hose inlet)
and connect the latches.
Tube
Handle
Tube
Combination
Floor Tool
Tube