Work Hero WD60LSS User manual

60L WET & DRY VACUUM
STAINLESS STEEL
2300W MAX TWIN MOTORS
WD60LSS
Ideal for:
Factories/Warehouses
Workshops/Garages
Cafes/Restaurants

SAFETY PRECAUTIONS
AND WARNING:
When using your vacuum cleaner, basic
precautions should always be observed,
including the followings;
1. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
2. Children should be supervised to ensure
that they do not play with the appliance.
3. To prevent electrical shock, do not immerse
the appliance, power cord or power plug
into water or other liquids.
4. To prevent electrical shock, do not use the
vacuum cleaner outdoors.
5. Always check the power cord before use,
the power cord and the plug should be in a
good condition and must not be damaged.
If the power supply cord is damaged or
defective, it must be replaced by the
manufacturer, its service agent or similarly
qualied persons in order to avoid a hazard.
6. Do not unplug by pulling on the power cord.
To unplug, grasp the plug not the power
cord. Use only Australian and New Zealand
electrical safety approved extension cords.
7. Do not pull or carry the appliance by the
power cable, use the power cable as a
handle or pull the power cable around
shaft edges or corners. Avoid running the
appliance over the power cable.
8. Ensure the appliance is switched o
before unplugging.
9. Do not handle or operate the appliance
with wet hands and follow electrical safety
precautions at all times.
10. Extreme caution should be exercised when
using the appliance on stairs.
11. Do not attempt to change the attachments
while the appliance is plugged in to mains
power supply. Switch o and remove
plug from mains power supply. Use only
manufacturer’s recommended accessories.
12. Do not operate the vacuum cleaner too
close to the heaters, radiators and other
hot surfaces.
13. Do not use the appliance to pick up
ammable items or combustible liquids
(i.e. petrol, hot ashes cigarettes, matches,
explosive materials or anything burning)
or use in areas where such substances and
items may be present.
14. Do not use the appliance to pick up toxic
materials (i.e. chlorine bleach, ammonia).
15. Ensure the appliance is disconnected from
the main power supply before connecting
the hose to the unit.
16. Do not operate or use the appliance within
dust bag and/or lters in place.
17. Before vacuuming, remove any large or
shaft objects from the oor or cleaning
surface in order to prevent damage to
the lter.
18. If the air inlet, oor head or the telescopic
tube is blocked, switch o the cleaner straight
away and remove from the main power. First
clear the blocked object before attempting to
start the cleaner vacuum again.
19. Hold the plug when rewinding onto the
cord reel. To prevent accidental injury do
not allow the plug to whip when rewinding.
20. Do not leave the appliance unattended when
it is connected to a mains power supply
21. Before carry out any maintenance service
or cleaning the lters, always switch o the
vacuum cleaner and disconnect the plug
from power supply
22. Keep ends of the hose, telescopic tube
and other openings away from your face
and body.
IMPORTANT
Always switch o the cleaner and remove the plug from the mains power supply before cleaning
your appliance, when not in use or attempting any maintenance task. The cleaner must only be
connected to an AC power supply at the voltage shown on the rating label. This cleaner should
only be used for its intended purpose as described in this instruction manual. Never operate the
vacuum cleaner without lters.

WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS  WD60LSS 01
1. Do not operate the vacuum cleaner too close to heaters, radiators, and
other hot surfaces.
2. Before inserting the plug into the wall, make sure your hand is dry.
3. Before turning on the vacuum cleaner, remove any large or sharp objects
from the oor or cleaning surface in order to prevent damage to the lter.
4. When you want to pull the plug from the wall, do not unplug by pulling on
cord. To unplug, grasp the plug, not the cord.
5. If the air inlet or oor head or tube are blocked, you should switch o the
cleaner straight away and remove from mains power. First clear the blocked
substance before attempting to start the vacuum cleaner again.
BEFORE YOU BEGIN
23. Do not use the vacuum cleaner if it
is damaged or breaks down. Check
the electrical regularly for defects. If
connection cables, electrical hoses,
electrical contacts and electric tubes are
damaged, have them replace immediately.
24. Never clean the vacuum cleaner or any of
the electrical parts, especially the electrical
connections with water or liquid cleaners.
25. Never attempt to make any modications
electrically to the vacuum cleaner.
26. Always store the appliance indoors in a
cool and dry place.
27. Damage caused by improper use or by not
observing the instructions in this manual
will void warranty.

02 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
KNOW YOUR PRODUCT
1. Handle
2. Hose
3. Carry Handle
4. On/O Switch
5. Connection Latches
6. Tank
7. Hose Inlet
8. Tank Wheels
9. Wet Pick Up Floor Tool
10. Two-piece Metal Tube
11. Drainpipe
12. Handle Reversal
13. Power Cord Plug
14. Crevice Tool
15. Dusting Brush
16. Combination Floor Tool
1. Handle
11. Drainpipe
12. Handle Reversal
2. Hose
4. On/O
Switch
5. Connection
Latches
6. Tank
7. Hose Inlet
8. Tank Wheels
16. Combination
Floor Tool
14. Crevice
Tool
9. Wet Pick Up
Floor Tool
10. Two-piece
metal tube
3. Carry
Handle
15. Dusting
Brush
13. Power Cord Plug

WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS  WD60LSS 03
02 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
ASSEMBLY
The cleaner should be switched o and disconnected from the mains power supply before you
start to assemble.
Part 1
1. Connect the 2-piece metal tube together.
2. Connect the handle on the hose to the tube.
3. Connect the tube to the combination oor tool or the wet pick up tool.
Tube
Handle
Tube
Combination
Floor Tool
Tube
Part 2
1. Disconnect latches on side of machine and remove the canister lid.
2. Remove all accessories from inside the tank.
3.
Replace the canister lid (with the power cord facing the opposite direction of the hose inlet)
and connect the latches.
4. Insert the hose connector into the hose inlet and turn clockwise until it locks securely
onto the machine.
5. Take the cable from the storage area and connect to the mains power supply.
6. Start the cleaner by pressing the On/O button.

04 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
ACCESSORIES
The combination oor tool is ideal for cleaning on carpets and hard oors.
The wet pick up oor tool is ideal for wet applications.
Fitting the dusting brush and crevice tool
To t the accessories to the tube, gently insert the tube into the top of the dusting brush
or crevice tool.
Dusting Brush – ideal for cleaning furniture, curtains and upholstery
Crevice Tool – ideal for cleaning in tight spaces
Carpet Hard Floors
Crevice
Tool
Dusting
Brush

WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS  WD60LSS 05
04 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
OPERATION
ATTENTION: DISCONNECT FROM MAINS POWER SUPPLY BEFORE DOING ANY
MAINTENANCE WORK.
Dry Vacuum Cleaning
1. Ensure the sponge lter and cloth bag is always tted before the cleaner is used.
2. Once the tank is full we recommend the tank to be emptied and cleaned out.
3. The cloth bag also needs to be emptied and clean accordingly.
Wet Vacuum Cleaning
1. Ensure the sponge lter is tted and the cloth bag is removed before the cleaner is used.
2. Clean the tank after each use. Avoid leaving dust or dirty water in the tank.
3. Wipe the machine inside and out from time to time , using only luke warm water.
Before use always examine the power cable for cuts and/or damage.
4. Wet pick up accessories should be washed periodically.
On/off switc
h

06 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
4. Wash and clean the lter and bag carefully
using luke warm water.
3. Remove the cloth bag.
5. Dry by airing for at least 24 hours. 6. Re-t the lter and cloth bag into the machine.
2. Unlock the locking knob and remove
the sponge lter.
1. Release the locking latches to remove the
canister lid.
MAINTENANCE
If proper care is taken to maintain your cleaner, motor maintenance is unnecessary.
However we recommend that your cleaner is serviced once a year.
Cleaning Filter
Sponge filter Cloth Bag
Sponge filter Cloth Bag
Cloth Bag
40°C
max
24hr
Sponge filter Cloth Bag
Sponge filter Cloth Bag
Cloth Bag
40°C
max
24hr
Sponge filter Cloth Bag
Sponge filter
Cloth Bag
Cloth Bag
40°C
max
24hr
Sponge filter Cloth Bag
Sponge filter
Cloth Bag
Cloth Bag
40°C
max
24hr
Sponge filter Cloth Bag
Sponge filter Cloth Bag
Cloth Bag
40°C
max
24hr
Sponge filter Cloth Bag
Sponge filter Cloth Bag
Cloth Bag
40°C
max
24hr

WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS  WD60LSS 07
06 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
Cleaning the Tank
1. Release the locking clip to unlock the barrel from the base.
2. Remove the cloth bag.
3. Empty the tank and clean the inside of it thoroughly.
4. Clean and wash the cloth bag where appropriate.
5. Remove the hose connector from the hose inlet and drain it thoroughly.
Take out
Drain

08 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
TROUBLESHOOTING
TROUBLE POSSIBLE CAUSE REMEDY
Suction weakens or
cleaner runs hot
Clogged lter Brush dirt from lter. If condition continues,
change lter.
Air Leak Check all ttings for tight t (oor tool, hoses,
etc.). Check that tank cover is sealed properly.
Obstruction in hose
or oor tool
Check oor tool, hose, etc. for obstructions, and
remove if present.
Misting in the exhaust air Saturated lter Replace saturated lter with a dry lter.
CUSTOMER CARE
For customer service or product enquiries please contact 1800 815 270
PRODUCT NUMBER PRODUCT DESCRIPTION
33151780 Tank stainless steel
33500383 Wheel caster
33500384 Wheel caster with brake
31110223 Combination Floor Tool 40mm
31220455 Complete Hose Assembly 40mm
31300563 Rod 40mm (2 piece) stainless steel
31130091 Dusting brush 40mm
31120106 Crevice Tool 40mm angled end
32200829 Filter, sponge
32440319 Cloth Bag
33151779 Pipe, drain assembly
33500385 Rear Wheel

WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS  WD60LSS 09
08 WORK HERO 60L WET & DRY VACUUM STAINLESS STEEL 2300W MAX TWIN MOTORS
This warranty commences from the original date of
purchase and is not transferable; please retain your
original proof of purchase for any warranty claims.
This warranty is valid only in the country where the
cleaner is purchased.
The cleaner must be operated in accordance with
these instructions. This cleaner is not designed for the
collection of vitreous building material including particle
board, construction products and similar products
such as wood/fibres, cement, fillers, fibre glass etc or
excessive or frequent sand. The infrequent pick-up
of these materials in these circumstances may be
harmful to your cleaner and may void the
manufacturer’s warranty.
Accessories and consumables including dust bags
and filters, unless defective in manufacture, are not
subject to this warranty. In order to prolong the life of
accessories and consumables, regular care and
maintenance is recommended.
When properly used and cared for, your cleaner
will render excellent service; refer to the instruction
manual for further details, as misuse or failure to
follow the instructions makes this warranty void.
In the event of service or advice being needed,
please contact International Cleaning Solutions Pty
Ltd, ACN 119 462 798, Level 1, Building 2 Brandon
Business Park, 530 Springvale Rd, Glen Waverley,
VIC 3150. Customer Care: 1800 815 270.
The decision to repair or replace the cleaner is at the
sole discretion of International Cleaning Solutions Pty
Ltd. If International Cleaning Solutions Pty Ltd decide to
repair or replace the cleaner, it will do so at its own cost.
International Cleaning Solutions Pty Ltd is unable to
accept responsibility under this warranty for any repair
work not carried out by an authorised International
Cleaning Solutions Service Agent or from the use of
non-genuine parts. If any part is no longer available
or manufactured, International Cleaning Solutions will
replace it with a genuine functional replacement part.
This warranty does not apply to the cost of replacing
any parts of the product due to normal wear and tear,
alterations, improper installation, physical abuse, misuse
or accidental damage. Any transportation costs
involved in the repair of defective parts shall be borne
by the claimant.
If proof of purchase cannot be provided at the time of
a warranty claim or service, any work carried out on
the cleaner is chargeable. The repair or replacement
of the cleaner under this warranty does not extend
the original period of warranty.
The benefits conferred by this warranty are in addition to
all other rights and remedies in respect of the product
as outlined under the Competition and Consumer Act
and other State and Territory laws.
“Our goods come with guarantees that cannot be
excluded in the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure
and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not
amount to a major failure.”
Keep this Guarantee and your receipt as proof of purchase
Purchase Date ......./......../.........
Our policy is one of continuous development and accordingly we reserve the right
to change specifications without prior knowledge.
International Cleaning Solutions Pty Ltd.
(ACN 119 462 798)
Level 1, Building 2, Brandon Business Park,
530 Springvale Road, Glen Waverley, Victoria, 3150.
This is a parts and labour warranty against product defects
and failures, when the product is used in accordance
with the terms and conditions of this warranty statement.
WARRANTY
3 Month

Product Code: 11500125
International Cleaning
Solutions Pty Ltd
(ACN 119 462 798)
Level 1, Building 2
Brandon Business Park
530 Springvale Rd
Glen Waverley, VIC 3150
Customer Care: 1800 815 270
Made in China
V1 0313
TECHNICAL INFORMATION
Model: WD60LSS
240V ~ 50Hz
2300 MAX