Workrite Line of Sight LOS3-B-M11 Series User manual

1 of 8 Line of Sight | [phone] | los.workriteergo.com
Ganging Brackets, Filler Channels, Back
to Back End Panels, Power System
Components, CPU Holders
ALine of Sight Single User Manual Chassis
Qty: 1 BLe Top Bracket
Qty: 1 CRight Top Bracket Qty: 1 I Le Foot
Qty: 1
JRight Foot Qty: 1
L⅜" Glides Qty: 4
H#10-¾" Phillips Pan Head Screws
Qty: 30
D"-18 Serrated Flange Nut
Qty: 4
K⅜-16 x 1" Flange Head Cap Screws
Qty: 4
GLid Stop Qty: 2
EWorksurface Qty: 1 FManual Monitor Bay Lid
Qty: 1
Optional, Sold Separately
Parts Included:
Worksurface & Monitor Bay Lid
Foot Kit
Chassis Hardware Kit: 4435564
Assembly Instructions: Manual, Single User
Workstation Chassis: LOS3-B-M11-XX-XX-XX-X
✓ Verify That You Have All The Tools Needed For The Assembly
You will need the following tools:
Drill/driver or Phillips screwdriver with #2 tip
" or 4mm Allen wrench
½" Open ended wrench
" Open ended wrench
CAUTION: Manual Li models are spring loaded
and require extra care until a monitor has been
installed. Follow all warnings and cautions.
V
Wire Loom, 1" × 2'
Qty: 1
MVESA Mount Qty: 1
UCable Ties Qty: 5
OPlastic Spacers Qty: 4N¼"-20 × ½" Allen, Button Head Screw
Qty: 2
PM4 × 10 mm Monitor Screw
Qty: 4 QM4 × 16 mm Monitor
Screw
Qty: 4 RM4 × 25 mm Monitor
Screw
Qty: 4
S#10 Zinc Washer Qty: 4 TCable Clips Qty: 3
Monitor Mount & Wiring Hardware Kit, Manual: 4435563
9/16"
Hex
13/16"
25/64" 1"
0.375"
3/8"-16 Thread
PUSH HERE TO RAISE OR
LOWER THE MONITOR
Caution: Spring loaded mechanism.
Exercise caution when cycling up or down!
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
5/32"
Hex
0.437"
0.25"
0.132"1/2"
1/4"-20 Thread
36" model shown
or

2 of 8 Line of Sight | [phone] | los.workriteergo.com
1 Remove Front and Rear Panels, Set Power Cord Aside
1.1 Remove the Front and Rear Panels from the Chassis (A) by
turning the Panel Locks a quarter turn towards the center
of the panel (inward), then pivot the panels forward to
remove.
If you have Locking Panels, unlock using the included key.
1.2 Keep the protective tape around panels and on frame
until assembly is complete to protect finish.
2 Attach Top Brackets
Attach the Le Top Bracket (B) and Right Top Bracket
(C) to Chassis (A) with the four "-18 Locknuts (D).
Threaded studs on the brackets insert through holes in
the Chassis and are held in place with the Locknuts.
Removable Panel Locking Panel
3 Attach Lid Stops to Worksurface
Note: Build Assembly in a large, clean area on carpeting or
moving blankets to prevent damaging Worksurface and Lid.
3.1 Place Worksurface (E) and Monitor Bay Lid (F) upside down on
floor. Slide Monitor Bay Lid (F) into cutout in Worksurface (E).
3.2 Attach both Lid Stops (G) with eight #10-¾" Phillips Pan Head
Screws (H).
A
B
C
F
C
D
D
1.2
1.1
1.1
3.1
3.2
Front
Panel
Threaded
Studs
Rear
Panel
Panel
Lock
Protective
tape
Under Top Bracket
E
G
H
H#10-¾" Phillips Pan Head Screws
Hardware at actual size
D"-18 Serrated Flange Nut
Hardware at actual size

3 of 8 Line of Sight | [phone] | los.workriteergo.com
4 Flip Chassis Upside Down Onto Worksurface
4.1 Place the Worksurface and Monitor Bay Lid
upside down on the floor and slide the Monitor
Bay Lid into the cutout in the Worksurface.
4.2 Flip the Chassis assembly upside-down onto the
bottom of Worksurface
Use at least two people to flip over and position
the Chassis.
4.3 Align Chassis assembly so holes in Top Brackets
line up with pre-drilled holes in Worksurface and
holes in Monitor Bay Hinges line up with pre-
drilled holes in Monitor Bay Lid.
5 Mount Chassis Assembly to Worksurface and Monitor Bay Lid
5.1 With Chassis Assembly correctly positioned on Worksurface, attach
Chassis Assembly to Worksurface with eight #10-¾" Phillips Head Screws
(H), four screws per Top Bracket (B & C).
5.2 Note: Chassis models over 48" have a Center Support which requires two
#10-¾" Phillips Head Screws (H) into the Center Support.
5.3 Attach Monitor Bay Lid to both Monitor Lid Hinges with two
#10-¾"Phillips Head Screws (H) per hinge at the forward location. You will
finish installing the hinges in Step 10 when workcenter is right side up and
you can more easily access the two other hinge screw holes.
Note: Monitor Bay Lid will
have approximately .2" of
clearance around the cutout in
the Worksurface when properly
installed.
5.4 Attach the Lid Stay to the Monitor Bay Lid with two #10-¾" Phillips Pan Head Screws (H)
(see Adjustment Procedure, Step 11).
4.1
4.2
4.3
Monitor
Bay Lid
Monitor
Bay Hinge
Worksurface
Lid Stay
Attach to Worksurface Attach to Monitor Bay Lid
5.1
5.2
5.3
5.4
H
H
H
C
B
H
H
H
Two screws H
per hinge at
forward locations
Center Support on
models over 48" wide
H#10-¾" Phillips Pan Head Screws
Hardware at actual size

4 of 8 Line of Sight | [phone] | los.workriteergo.com
6 Attach Feet and Glides
6.1 Attach Le Foot (I) and Right Foot (J) from
the inside, bottom of Chassis using four
⅜-16×1¼" Flat Head Socket Cap Screws (K).
Note that the Le Foot will be on the right and
vice versa with the Chassis is upside down.
6.2 Screw in the four Glides (L) into the feet
approximately half way. You will level the
Workcenter once it has been flipped right side up.
7 Flip Workcenter Over
Flip over the assembled Workcenter with at least
two people.
8 Remove Safety Screw
Remove the Safety Screw from the top of the Monitor Li with a #2 Phillips
screwdriver. Remove, but retain the screw in case you need to ship the
Workcenter without a monitor in the future.
CAUTION: The Monitor Li is spring loaded! Removing the Safety Screw
unlocks the mechanism allowing the Monitor Li to raise.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION !
Product is spring loaded and may open with extreme force when screw is removed.
MISE EN GARDE !
Le produit est à ressort et peut s’ouvrir avec un force extrème lorsque cette vis est enterèe.
¡
ATENCIÓN !
Éste producto estàcargado con resortes y puede abrise con extrema fuerza cuando
se remueve éste tornillo.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
CAUTION!
Do not opperate without proper counterbalance
weights in place. Personal injury and/or damage
could occur.
MISE EN GARDE !
Ne faites pas fonctionner sans des contrepoids
appropriès en place. Blessures et/ou des dommages
pourraient survenir.
¡ATENCION!
No operar sin los contrapesos adecuados en su lugar.
Podrían ocurrir daños personales.
6.2
6.1
6.1
KI
J
K
K
K
L
K⅜-16 x 1" Flange Head Cap Screw
Hardware at actual size
Under Workcenter
Top of Monitor Li

5 of 8 Line of Sight | [phone] | los.workriteergo.com
10 Complete Monitor Bay Lid Attachment
Finish attaching Monitor Bay Lid to both
Monitor Lid Hinges with two remaining
#10-¾" Phillips Head Screws (H) per hinge.
Note: Monitor Bay Lid will have
approximately .2" of clearance around the
cutout in the Worksurface when properly
installed. You may need to loosen the Hinge
Screws to adjust and re-tighten.
11 Adjust Monitor Bay Lid-Stay Resistance
Use " or 4mm Allen wrench to turn
Adjustment Screw clock-wise until lid closes
soly and completely when released.
If lid doesn't close completely, turn
Adjustment Screw counter-clockwise
slightly until lid closes soly and completely
when released.
9 Raise Monitor Li
9.1 Li Lid fully open.
9.2 Press down on "PUSH HERE" label on top of the Manual Lis.
CAUTION! Spring loaded mechanism! Take care during
the first time Monitor Arm is activated. With no monitors in
the Monitor Mount, the mechanism is FULLY LOADED and
will spring up with maximum force.
PUSH HERE TO RAISE OR
LOWER THE MONITOR
Caution: Spring loaded mechanism.
Exercise caution when cycling up or down!
9.2
H
H#10-¾" Phillips Pan Head Screws
Hardware at actual size
Previously installed
in Step 5.3
Monitor Bay
Lid Handle
Adjustment Screw
9.1 9.2
Monitor Li
" Allen wrench

6 of 8 Line of Sight | [phone] | los.workriteergo.com
13 Set Counterbalance Weight
Note: You will need to establish an equilibrium between
the weight of the monitor with Ballast Plates and the liing
force of the Monitor Li. Ballast Plates are best reached
from under the worksurface.
Remove the Wing Nut. With the
monitor installed, remove ballast
plates until the monitor fully
raises when the Monitor Li is
engaged.
Replace the Wing Nut to secure
in place.
12 Mount VESA Compatible Monitor to Monitor Li
Note: You will need to mount the monitors in order to determine
the correct installation height and counterbalance weight.
Remove the monitor from the factory mount if necessary, and
retain the screws that came with the monitor for Step 12.1.
12.1 Attach VESA Plate (M) to the back of your VESA compatible
Monitor with Spacers (O), Screws (P, Q,R) and Washers (S) or use
the screws that came with your monitor. Always use the shortest
screws possible, so you do not damage your monitor.
12.2 Attach the VESA Bracket Monitor Assembly as high as possible
on the Monitor Li using two ¼"-20 × ½" Button Head Screws (N)
and the " Allen wrench.
PM4 × 10 mm Monitor Screws
QM4 × 16 mm Monitor Screws
RM4 × 25 mm Monitor Screws
N¼"-20 × ½" Button Head Screw
12.2
12.1
VESA compatible
monitor
Ballast Plate
Wing Nut
Attach VESA Bracket
Monitor Assembly
Under Worksurface
M
or
PQR
Important Note: It is strongly recommended to use
the mounting screws provided by the monitor manufacturer
if possible. If longer screws are required, use the shortest
screws possible to avoid damage to the monitor.
N
" Allen wrench
Hardware at actual size

7 of 8 Line of Sight | [phone] | los.workriteergo.com
18 Remove Protective Tape & Replace Front and Rear Panels
18.1 Remove the protective tape on the Panels and Chassis
18.2 Reattach your front and rear panels. You now have a
complete Workcenter. Finish building all Workcenters
before proceeding to final room assembly.
15 Install Optional Accessories for Your Configuration
With the monitors and power components installed, you will now need to add your optional accessories
like Worksurface Grommets, Remote Controls and CPU Holders. Follow the instructions with the Optional
Accessories to complete this step.
16 Install Technology for Your Configuration
With all Line of Sight components installed, you will now need to install all the technology components to
complete your system. Install all computers, peripherals like keyboards and mice, and network cabling to
complete your installation according to the manufacturers specifications and your specific application.
14 Install Power Distribution Options for Your Configuration
With the Workcenter built, you will now need to add your power options for your specific configuration. Follow
the instructions that came with the Power System Options to complete your configuration.
If you did not purchase the Power Track or Power Bar, skip to Step 15.
17 Manage Cabling
With monitors and technology installed, you'll want to
start considering all the cabling requirements.
Note: It is critical that no wires interfere with the travel
of the Monitor Li. Use Cable Clips (T) for single wires
(mouse & keyboard) and Cable Ties (U) for multiple wires
to fasten all cabling securely out of the way of all moving
Monitor Li components.
Use the Wire Loom (V) to
manage all user cables
routing from the keyboard
tray to the CPU. This may
include keyboard, mouse,
monitor and data cables.
Remove
Front & Rear
Panels
Chassis
Remove
18.1
18.2
V
TU
Keyboard tray
cable access
Monitor Li
To CPU

8 of 8 Line of Sight | [phone] | los.workriteergo.com
#1500380 Rev B
✓ Cleaning Instructions
Laminate Worksurfaces:
For everyday cleaning, wipe the surface with a damp cloth or sponge. Use a spray cleaning agent sparingly
if necessary (suggested spray cleaning agents are indicated below). Do not pour water directly onto the
worksurface. Wipe completely dry with a so rag using a straight line motion.
• Worksurfaces may need occasional dusting. To keep the surface in ideal condition, use a non-oily furniture
spray.
• Diicult stains such as coee can be removed using a mild cleaning detergent and a so bristled (non-metallic)
brush. Do not scrub surfaces with too much force, otherwise the surface could lose its finish.
• Stubborn stains that resist any of the above cleaning methods may require the use of undiluted household
bleach. Apply a very small amount of bleach (approximately ¼-capful) to the stain and let stand no longer than
two minutes. Rinse thoroughly with warm water and wipe dry. WARNING: Prolonged exposure of the laminate
surface with bleach will cause discoloration.
• Ensure to always rinse laminate surfaces aer cleaning. Even a small amount of cleaning residue can result in
permanent discolorations.
• Recommended Laminate Worksurface cleaning agents:
· Non-abrasive spray cleaning agents: Dawn, Fantastik, Windex, Lysol
· Furniture spray: Pledge
· Stain removers: Lestoil, Clorox
Painted steel parts:
• Clean surfaces regularly with damp cloth
• If necessary, use a spray cleaning agent (e.g. Fantastik) sparingly. Wipe completely dry with a so rag using a
straight line motion.
• Lightly brush both vertical and horizontal surfaces to prevent dust build-up
Polished chrome feet:
• The feet can be polished when they become dull with Aluminum polish (e.g. Flitz or Mothers Mag Polish) with
special attention to keep polish from painted surfaces. Follow manufacturers instructions for best results.
19 Assemble Final Room Configuration
With all individual Workcenter Built and electrical installed, arrange Workcenters according
to your final room configuration. You will need at least two people to move a Workcenter.
Adjust the Glides (L) on the bottom of the Feet to assure each Workcenter is level and stable in its final location.
Note: It is critical that you follow all warnings and cautions when you get to final assembly. Consult the
instructions that came with your electrical components and follow all cautions and warnings carefully!
Configurations with shared power must conform to code and include use of Ganging Brackets for Side to Side
configurations or Back to Back Filler Plates for Back to Back configurations.
Final assembly will include testing of electrical components and functioning of all Monitor Lis.