World Dryer AIRFORCE User manual

Operating Instructions and Parts Manual Model “J4”
Printed in China
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain
the product described. Protect yourself and others by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property damage. Retain instructions for future reference.
WORLD DRYER AIRFORCE™
High Efficiency Hand Dryer
_____________________________________________________________________________
Description
World warm air hand dryer, powered by universal brush motor, delivers 1100 Watts of drying
power. This hand dryer runs on 230 Volts AC electrical supply. An infrared sensor is used to
automatically turn the dryer on and off. This model is intended for use in commercial, industrial,
office and public facility environments.
General Specifications
Model Drying Cycle Dimensions Weight
(WxHxD)
J4-162 Black Auto 8.9” x 10.6” x 6.4” 7.1 lbs
J4-974 White Auto (22.6cm x 27cm x 16.2cm) (3.2 Kg)
J4-970 Chrome Auto
Electrical Specifications
UL LISTED E320188
Model Type Electrical Input Amperage Watts
J4 Automatic 230VAC-50/60Hz 4.8A 1100
Unpacking
1. Remove all packing material.
Recycling is recommended.
2. Carefully remove the hand dryer from the shipping carton, using care not to drop the
appliance.
3. Inspect carefully for any damage that may have occurred during transit. Check for any
loose, missing or damaged parts. If the hand dryer is damaged, promptly inform the
dealer where you purchased it.
68-300
Rev v.3

Operating Instructions and Parts Manual J4
WORLD DRYER AIRFORCE™
High Efficiency Hand Dryer
2
General Safety Information
DANGER Failure to disconnect the power source before installation can result in serious
injury or death from electric shock.
-Always disconnect the power source before servicing or installing the hand dryer.
DANGER Failure to properly ground this unit could result in severe electrical shock
and/or death
-This hand dryer must be properly grounded (Earthed) for safe operation. An identified
ground connection point is supplied on the chassis of the hand dryer.
-We recommend GFCI protection in wet or damp locations or as required by local code.
WARNING Risk of fire, personal injury or property damage are possible if local codes, or
safety recommendations are not followed.
-Use only the electrical power (voltage and frequency) specified for the model hand dryer
being installed.
-Connect the hand dryer to the nearest suitable distribution panel.
-To limit a voltage drop, and insure efficient operation, use No. 12 wire or larger as required
by local or National Electrical Code.
-Do not connect to a branch circuit with circuit breaker or fuse protection over 15 Amps.
-All automatic model hand dryers must have dedicated circuit.
-Route all field wiring away from moving parts within the hand dryer.
CAUTION Improper mounting could result in personal injury or property damage.
-Follow the mounting recommendations in Table 1.
-On a stud wall, one side of the hand dryer should be mounted to an existing stud.
Installation
1. Disconnect the power source.
2. Use the security hex key supplied to turn the cover mounting screws clockwise to remove
the cover from the dryer.
3. Place the hand dryer base on the wall at the desired location using Table 1 to determine the
recommended mounting height. With the base so located, use it as a template to mark
locations of the 4 mounting bolt holes on the wall. Ensure that no reflective object (such as
a hand basin) is located directly under infra-red sensor eye; the minimum distance is 18
inches (46 cm).
4. Fasten the base to the wall, using the type of bolts suggested in Table 2.
5. All automatic dryers must have their own dedicated 15 amp circuit.
6. Connect the dryer to the nearest suitable distribution panel.
7. Replace cover, turn screws counter-clockwise making certain not to over-tighten.
IMPORTANT: Consult local and general regulations before performing dryer installation. Ensure
that the electrical network is not overloaded. Do not connect to a branch circuit over 15 amps.

Operating Instructions and Parts Manual J4
WORLD DRYER AIRFORCE™
High Efficiency Hand Dryer
3
Maintenance
1. Remove fuse or shut off power to the dryer at fuse box.
2. With Allen wrench supplied with dryer, turn clockwise two Allen screws from bottom side
of dryer case.
3. Remove dryer cover.
CLEANING INSTRUCTIONS
Read complete instruction before proceeding. Under normal use, cleaning the Dryer once a year
will keep it in good operating condition. If the washroom traffic is heavier than normal, the
cleaning should be done every 6 months. Lint and dust build up inside the dryer can result in
damage to motor.
1. Turn off dryer at circuit breaker or fuse panel.
2. Turn clockwise two cover mounting screws from dryer cover using security hex key
provided. Support cover while removing screws.
3. Vacuum out dirt from blower and housing. Use caution not to damage wires or circuit
boards.
4. The motor inlet cover may be removed by unscrewing the (4) screws. This allows access to
the motor for cleaning or replacement.
5. Use soft-medium bristle ½” paint brush to clean dust and dirt from motor.
6. Replace cover. Place cover squarely over base and push flush to wall. Turn cover mounting
screws counter-clockwise and tighten until snug. Do not over tighten.
Table 1
Recommended Mounting Heights from Floor to Dryer Bottom Edge
in.(cm.)
Men’s washrooms 46 (117)
Women’s washrooms 44 (112)
Children’s washrooms, ages 4-7 32 (81)
Children’s washrooms, ages 7-10 36 (91)
Children’s washrooms, ages 10-13 40 (102)
Children’s washrooms, ages 13-17 44 (112)
Handicap Mounting Height 37 (94)
Table 2
Type of Wall Type of Bolt Minimum Bolt Length
Hollow Tile, Lath, Wall Board or Metal ¼” (M6) screw Type or Wing Type toggle Bolts Dependent on wall thickness
Cement, Brick, or Tile Covered Cement or Brick ¼” (M6) Stud Type Expansion Bolts 3” (76mm)
Stud Wall with wood Backing No 16 (M8) Wood Screws 2-3/4” (70mm)

Operating Instructions and Parts Manual J4
WORLD DRYER AIRFORCE™
High Efficiency Hand Dryer
4
REPAIR PARTS LIST FOR AIRFORCE™ HAND DRYER
Reference Description Part Number Qty
Number
1 Base 14-011577 1
2 Motor Housing 47-011573 1
3 Earth Clip 52-030244 1
4 Cable Clamp 12-011578 1
5* Screw-No6 x 1/2 - Poz Pan 46-040121 4
6* Screw-No8 x 3/8 - Poz Pan 46-040049 4
7* Screw-No6 x 3/8 - Poz Pan 46-010008 3
8 Screw M5x16 Plas Tech 30 Flange HD 46-333 4
9 Seal 59-011574-1 1
10 Outlet Lens 30-011576 1
11 Motor 32-12214300 1
12 Screw M4x10 Taptite Poz Pan 46-040194 2
13 Motor Cover with Muffler Felt 20-200901 1
14 Cover Bracket 33-011579 2
15 Cover 20-030243 1
16 World Sensor PCB 49-200 1
17 Cover Screw Cap 59-011587 2
18 M6x25 Sac HD Cap Screw 46-040221 2
19 Bracket, Power Circuit Board 33-200 1
20 World Motherboard 16-200 1
21* Screw-No4-3/8 P/Plan Plasfix 60 46-040229 4
22 BrassNutM5 35-007J 2
23* Installation Kit (Screw w/Washer #8 and Anchor) 46-90398K 4
24 Fishpaper J/ J4 PCB Insulator 12-8490 1
25 Mounting Isolation Kit (Spacer + 2 Grummets) 59-005517K 4
26 Fixing Kit “5 mm Allen wrench” 56-40189 1
27 Gasket, Motor Chamber 27-200903 1
28* Screw #6x3/8 SS Truss Phillips 099-058 2
29 GroundScrew 46-002J 1
(*) Standard Hardware Store Fasteners.

Operating Instructions and Parts Manual J4
WORLD DRYER AIRFORCE™
High Efficiency Hand Dryer
5
For Repair Parts, call in the US 1.800.323.0701
Please provide following information:
-Model number
-Serial number
-Part description and number shown in parts list